Thingiverse
Dismountable 3D printer enclosure by robas
by Thingiverse
Last crawled date: 3 years ago
This is a dismountable 3D printer enclosure I built specially for my E3D BigBox printer, but you can adapt it easily for any other size printer. It can be disassembled and stored when not in use. The principle is simple; the case is built with square (and hollow) aluminum tubes connected with 3D printed corner pieces. In every corner piece (except for the roof), I glued a small (10x10x4 mm) neodymium magnet (see the pictures), making it very easy to dismantle or rebuild the case. The whole enclosure can be built-up within a minute.
The side perspex panels are mounted with magnets so they can be taken off in case you need to access the printer for maintenance.
You can place a 80mm fan in order to regulate the temperature, but I found that the temperature hardly comes higher than 35°C, even when printing with the heated bed at 120°C.
Printing filament used: PLA and Taulman Alloy 910
Print settings.
I printed the corner pieces and the hinges with Taulman Alloy 910. You can try another material, but Taulman did the job for me. Don't use PLA since it is too brittle !
I printed the corner pieces horizontal with raft and support, just to be sure that the pieces were 100% straight, because Alloy 910 did tend to warp a little on my PEI bed. Infill was at 20%. The parts fit tightly in the aluminum profiles, I had to hammer them in. Don't hammer directly on the pieces, but use for example a piece of wood to dampen the blows (or use a dead blow hammer).
Aluminum bars needed for BigBox
The aluminum bar size I used is 15 x 15 mm
Front / back panels
4x upright bar 690 mm high
4x horizontal bar 595 mm long
Side panels
4x upright bar 690 mm high
4x horizontal bar 530 mm long
Roof panel
2x front / back bar 595 mm long
2x side bars 560 mm long
Magnets
16 x cube magnets (10 x 10 x 4) mm for the the corner pieces
12 x round magnets (12 mm diameter, 1 mm thick) for the doors and the side panels
Perspex panels
Clear perspex for front doors and roof.
2 x Doors 295 x 688
1 x Roof 558 x 594
Channel plate for back doors and side panels
2 x Doors 295 x 688
2 x Side panel 528 x 688
3D printed parts:
Taulman Alloy 910 or any other high tensile strength polymer.
4 x Roof corner piece
4 x Front and back panels corner piece
4 x Side panels corner piece
4 x Hinge doorpost left
4 x Hinge doorpost right
4 x Hinge door left
4 x Hinge door right
PLA or any other (cheap) material:
8 x Door and side panel knob
2 x Doors upper magnet holder
8 x Side panel magnet holder
4 x Roof panel bearer corner piece
4 x Roof panel bearer middle piece
1 x fan protector (for 80mm fan)
The side perspex panels are mounted with magnets so they can be taken off in case you need to access the printer for maintenance.
You can place a 80mm fan in order to regulate the temperature, but I found that the temperature hardly comes higher than 35°C, even when printing with the heated bed at 120°C.
Printing filament used: PLA and Taulman Alloy 910
Print settings.
I printed the corner pieces and the hinges with Taulman Alloy 910. You can try another material, but Taulman did the job for me. Don't use PLA since it is too brittle !
I printed the corner pieces horizontal with raft and support, just to be sure that the pieces were 100% straight, because Alloy 910 did tend to warp a little on my PEI bed. Infill was at 20%. The parts fit tightly in the aluminum profiles, I had to hammer them in. Don't hammer directly on the pieces, but use for example a piece of wood to dampen the blows (or use a dead blow hammer).
Aluminum bars needed for BigBox
The aluminum bar size I used is 15 x 15 mm
Front / back panels
4x upright bar 690 mm high
4x horizontal bar 595 mm long
Side panels
4x upright bar 690 mm high
4x horizontal bar 530 mm long
Roof panel
2x front / back bar 595 mm long
2x side bars 560 mm long
Magnets
16 x cube magnets (10 x 10 x 4) mm for the the corner pieces
12 x round magnets (12 mm diameter, 1 mm thick) for the doors and the side panels
Perspex panels
Clear perspex for front doors and roof.
2 x Doors 295 x 688
1 x Roof 558 x 594
Channel plate for back doors and side panels
2 x Doors 295 x 688
2 x Side panel 528 x 688
3D printed parts:
Taulman Alloy 910 or any other high tensile strength polymer.
4 x Roof corner piece
4 x Front and back panels corner piece
4 x Side panels corner piece
4 x Hinge doorpost left
4 x Hinge doorpost right
4 x Hinge door left
4 x Hinge door right
PLA or any other (cheap) material:
8 x Door and side panel knob
2 x Doors upper magnet holder
8 x Side panel magnet holder
4 x Roof panel bearer corner piece
4 x Roof panel bearer middle piece
1 x fan protector (for 80mm fan)
Similar models
thingiverse
free
Lack table corner brace for front by goodwija
... will add the magnet size later. this enable you to add magnets to the perspex sides/front to enable easy removal of the perspex.
thingiverse
free
Hinges for perspex front panel on Flashforge Creator by andycap
...e 1.75mm so you could use a bit of abs off the roll or a piece of wire.
i will mount them with double sided tape or super glue.
thingiverse
free
Igloo cooler replacement Latch by wdsparrow
...y - unbreakable. all of that is assuming you print it in taulman nylon alloy 910. when you print it, it prints fully assembled.
thingiverse
free
Flsun Kossel Plexiglass Enclosure by Xlemos
...el is hold with 6 10mm x 3mm magnets.
print: 3x corner back, 4x corner front, 1x corner front bottom r, 1x corner front bottom l.
thingiverse
free
CTC Bizer Dual (and others) doors and lid by willefg
...s; bottom corners
70x m3x12
70x m3 nut
optional:
2x l+r brush holders; left & right brush holder
1x rear brush holder: <--
thingiverse
free
Creator X Enclosure (magnetic front door) by bookmake
...
acrylic front door 380x245x4mm acrylic sheet.
kit consists of hinge for 4 mm thick acrylic door, door handle and magnets holder.
thingiverse
free
FLSUN QQ-S - Enclosure by mcae1
...e acetate on the side sections to the towers
i used 10mm magnets for the side pieces and door - will also take up to 20mm magnets
thingiverse
free
SapphirePro or any 3d printer - Custom Door hinge and magnetic handle
...y 3d printer - custom door hinge and magnetic handle
thingiverse
you need 2x (10 mm x 8 mm) neodymium magnet for the door hinge.
thingiverse
free
Gopro mount kite by Daniel_Nilsson
...gopro mount kite by daniel_nilsson
thingiverse
mounts on the strut of the kite. printed with taulman alloy 910.
thingiverse
free
Hinge- and Grip set for Ultimaker 3 DIY front door by make-my-thing
...frame-side hinge parts should be fixed to the printer's front plate with small countersunk drywall bolts e.g. 2.5 mm x 10 mm.
Robas
thingiverse
free
TANTA ROBA necklace by bcs
...tanta roba necklace by bcs
thingiverse
tanta roba necklace
dimensions: 60x60x3,2 mm
thingiverse
free
Coffee cup holder by robas
... to print two nuts. first tighten one nut loosely, and tighten the second nut to the first nut, so it will function as a jam nut.
thingiverse
free
BigBox electronics cover fan by robas
...knob and the lid. you can find the hinges here: https://forum.e3d-online.com/index.php?threads/hinges-for-electronics-cover.1243/
thingiverse
free
Bigbox printing tools storage by robas
...it can hold 12 hot-end nozzles, both normal and volcano. there is a special place for a couple of pliers and a small wire cutter.
thingiverse
free
BigBox LCD Enclosure by robas
...ont of the panel :-)
parts needed:
4x m3 12mm screws for the lcd screen
6x m3 16mm screws for mounting the enclosure to the frame
thingiverse
free
LCD and switch holder for a BigBox printer by robas
...5mm.
see also this thread on the bigbox forum:http://forum.e3d-online.com/index.php?threads/project-whisper-arduino-version.1135/
thingiverse
free
Dump bucket for BigBox printer with linear rail by robas
...rt# 272854781845).
3x m3 hex screw and nut
both the height of the cup brush and the silicone wiper are adjustable (see pictures)
thingiverse
free
7inch PanelDue screen case for BigBox by robas
...s.
parts used:
9x m3x6 hex socket self tapping screw
1x 20cm 40pin gpio ribbon cable
2x 40pin 2.54mm male single row header strip
thingiverse
free
Spinner Nestor Kirchner spinestor by fedegiron
...stor kirchner spinestor by fedegiron
thingiverse
ojo que se roba todo lo que ve.... y ve para todos lados lados al mismo tiempo!
Dismountable
3d_export
$24
Bed with lifter 3D Model
...bed with lifter 3d model 3dexport bed folding dismountable bedroom furniture interior bedstead doss lifter bed with lifter...
3d_export
free
laserdock cnc laser docking station a opt lasers
...e can also be accessed through the webpage:<br>to learn further information about this device you can click the link below:
3d_export
free
laserdock cnc laser docking station b opt lasers
...ant to learn more about the capabilities of engraving and cutting laser heads it was designed to work with, click the link below:
3d_export
free
laserdock cnc laser docking station cover opt lasers
...earn further information about the engraving and cutting laser modules this docking station was designed for, feel free to visit:
3d_export
$80
us army m1126 stryker icv with detailed interior max 3ds
...g 3d models with superior quality. customized modeling service/format translation/additional tech support available upon request.
unity_asset_store
$10
Dismounted Knight
...ister necturus and speed up your game development process. find this & other characters options on the unity asset store.
thingiverse
free
Tool for dismount sight glass for Intex sand filter
...dismount sight glass for intex sand filter
thingiverse
this is a tool for dismounting the sight glass from the intex sand filter
thingiverse
free
Cannondale Front wheel dismount tool holder by anauff
...f a cannondale lefty bike you need a 5mm allen key.
i create this tool holder to always have the possibility to remove the wheel.
thingiverse
free
6mm Basic Napoleonic Cavalry -- Mounted and Dismounted by Braedzero
...al gamers, these should work fine as hussars and dragoons. included are a strip of 2 mounted, and a strip of 2 dismounted firing.
thingiverse
free
Multicopter propeller mount/dismount tool (For M4 & 13xx motor) by WindoAC
...t tool (for m4 & 13xx motor) by windoac
thingiverse
multicopter propeller mount/dismount tool
i use for emax 1306 motor (m4)
Enclosure
3d_export
free
electrical enclosure
...l enclosure where electrical devices like (relays, contactors, busbars ) are kept in order to protect from hazardous environment.
turbosquid
$100
GPU Enclosure
...yalty free 3d model gpu enclosure for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1381061)
3d_export
$5
Electrical Enclosure
...ed. also has tower lights attaced on the top.<br>file format that are available:<br>.step<br>.obj<br>.stl
archive3d
free
Enclosure 3D Model
...closure 3d model
archive3d
shower enclosure-acquarius- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-omega- 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-vega - 3d model for interior 3d visualization.
archive3d
free
Enclosure 3D Model
...enclosure 3d model
archive3d
shower enclosure-zenith - 3d model for interior 3d visualization.
turbosquid
$20
shower enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$14
Dumpster Enclosure
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
3d printer enclosure
... model 3d printer enclosure for download as ipt, skp, and fbx on turbosquid: 3d models for games, architecture, videos. (1634310)
Printer
archibase_planet
free
Printer
...inter
archibase planet
printer laser printer pc equipment
printer n120614 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Printer
...rchibase planet
laser printer office equipment computer equipment
printer - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$100
Printer
...er
turbosquid
royalty free 3d model printer for download as on turbosquid: 3d models for games, architecture, videos. (1487819)
turbosquid
$3
Printer
...turbosquid
royalty free 3d model printer for download as max on turbosquid: 3d models for games, architecture, videos. (1670230)
turbosquid
$1
printer
...turbosquid
royalty free 3d model printer for download as max on turbosquid: 3d models for games, architecture, videos. (1595546)
turbosquid
$1
printer
...turbosquid
royalty free 3d model printer for download as max on turbosquid: 3d models for games, architecture, videos. (1595105)
turbosquid
$10
Printer
...id
royalty free 3d model printer for download as max and 3dm on turbosquid: 3d models for games, architecture, videos. (1607146)
turbosquid
$7
Printer
...royalty free 3d model printer for download as ma, ma, and obj on turbosquid: 3d models for games, architecture, videos. (1644580)
turbosquid
$30
Printer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Printer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.