Thingiverse
LG840g-Cellphone-IpodShuffleCase by rickswirebox
by Thingiverse
Last crawled date: 3 years ago
For LG840G Cell Phones
See also my version without the ipod-shuffle case. Just a cover. http://www.thingiverse.com/thing:658862
Wanted to make use of my new ipod Shuffle and have with me when i wanted it. Use it sometimes plugged into my car stereo.
It prints fine. One thing to think of before printing is, to print separately. Do so because the phone-Clip part that pushes down over the ipod case part needs to print slower, about 20 to 30mm/s, while the case pictured was printed at 80mm/s. The phone-clip has the thin small finger clips which need to print slowly.
Works out nice because the phone-clip part will wear out with a finger clip breaking after a few months of pocket use. They print quickly.
Don't forget to use support for the phone-clip. Hate it, but the only way i could think to get all parts in and printable. You may have some areas that may need gluing some velvet or paper in to give a bit of more holding on the ipod case part. For a more of a snap in effect.
Hope you enjoy, Rick.
Note: The picture shows a small piece of thin card stock glued inside the top finger on the phone-clip part. The updated version 4 with the download should fix this without any card stock needed.
Update: Also wanted to add that the fingers may print a bit loose and not have the snap-in on the phone you may want. The thing i did with mine is; use a micro torch or maybe a hair drier to warm the top single finger and squeeze it in a bit. Should work fine and have the snap-in you like.
See also my version without the ipod-shuffle case. Just a cover. http://www.thingiverse.com/thing:658862
Wanted to make use of my new ipod Shuffle and have with me when i wanted it. Use it sometimes plugged into my car stereo.
It prints fine. One thing to think of before printing is, to print separately. Do so because the phone-Clip part that pushes down over the ipod case part needs to print slower, about 20 to 30mm/s, while the case pictured was printed at 80mm/s. The phone-clip has the thin small finger clips which need to print slowly.
Works out nice because the phone-clip part will wear out with a finger clip breaking after a few months of pocket use. They print quickly.
Don't forget to use support for the phone-clip. Hate it, but the only way i could think to get all parts in and printable. You may have some areas that may need gluing some velvet or paper in to give a bit of more holding on the ipod case part. For a more of a snap in effect.
Hope you enjoy, Rick.
Note: The picture shows a small piece of thin card stock glued inside the top finger on the phone-clip part. The updated version 4 with the download should fix this without any card stock needed.
Update: Also wanted to add that the fingers may print a bit loose and not have the snap-in on the phone you may want. The thing i did with mine is; use a micro torch or maybe a hair drier to warm the top single finger and squeeze it in a bit. Should work fine and have the snap-in you like.
Similar models
thingiverse
free
iPod Shuffle Case by c_bednar
...ipod shuffle case by c_bednar
thingiverse
thin wall case for ipod shuffle.
thingiverse
free
Ipod Shuffle by Hotrods2Hybrids
...shuffle case remixed into a childs toy phone - her name was merin if you want a different name let me know or remix for yourself!
cg_trader
free
ipod shuffle
...odel of an ipod shuffle. hope it helps you with anything. ipod apple shuffle music audio electronics phones small appliance phone
thingiverse
free
Fairphone 3+ Snap Fit Case by s_40
...e to print pla snap fit phone cases. they might help as a starting point to get the settings right for your printer and material.
thingiverse
free
Shims for 10/22 with magpul stock
.... you may or may not have to slighlty ream the hole in the washer. these parts are very thin, use the appropriate print settings.
thingiverse
free
Fairphone 3+ Snap Fit Case by s_40
...frame and one lower part. version one and two have different geometrys in the snap fit. v1 is easy to open, v2 is harder to open.
thingiverse
free
Official Standard Ipod 4 Case by 3D_Printable
...oblems with other ipod case files because they were mesh .stl files. these files should solve that problem if you are having it.
thingiverse
free
Big Clip with Mount by rj11
...gy part. it is held together with an m4x40 screw and a locknut. if you want to attach it to the mount, you need an m4x50 screw.
thingiverse
free
USB-C charger enclosure (for combining with other prints) by toozinger
...ore robust version later).
the last picture shows where i have used this enclosure with a person phone stand (still in progress).
thingiverse
free
Foldable Phone Stand by kaxorpie
...he updated stl file because it is better. i left the original up because it is marginally slimmer, but i prefer the updated one.
Rickswirebox
thingiverse
free
Clock-Dial-Floating by rickswirebox
...dial-floating by rickswirebox
thingiverse
5-3/4 inch diameter round with 1/2 inch numbers.
may be glued to most anything.
enjoy.
thingiverse
free
BreadBagClip by rickswirebox
...
update: check out the tator-chip-bag-clip, works great, it's here: http://www.thingiverse.com/thing:172376 thanks, rick.
thingiverse
free
XaxisClamp by rickswirebox
...rriage. i just used mine as is, but may later file it just a tiny bit.
hope this helps someone else.
happy 3d printing, rick.
thingiverse
free
Ipad/Tablet palm rests by rickswirebox
... notes or draws on tablet/ipad needs one of these or both.
makes note taking and drawing a breeze.
thanks, happy printing. :) .
thingiverse
free
Sandwich-Pack by rickswirebox
...top should slip right over the bottom and push down on the sandwiches keeping them ready to eat.
enjoy, happy printing....... :)
thingiverse
free
Mini_Squares by rickswirebox
...ed mine with 2, o.k but not perfect like i like. 26 minutes to print. easy cad to draw, don't get any easier.
enjoy, rick.
thingiverse
free
Small_Center_Square by rickswirebox
... square edges and hold/push the thumb support square while it hardens. just a thought.
mine printed well, hope you enjoy, rick.
thingiverse
free
PowerSupply_NameTags by rickswirebox
...as i did.
p.s. the middle part makes a great glue stick as well....... :) you can see i don't throw nothing away.........
thingiverse
free
Tator-Chip-Bag-Clip by rickswirebox
...omes through, here's the latest on my bread bag clip, find it here: http://www.thingiverse.com/thing:177088 thanks, rick.
thingiverse
free
12 inch Craftsman Bandsaw Blade Gaurd by rickswirebox
...in.
you may need to run a pocket knife around the edge just a bit for a tight, snug fit, but i like mine tight.
enjoy, rick.
Cellphone
turbosquid
$15
Cellphone
...alty free 3d model cellphone for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1186558)
turbosquid
$5
Cellphone
...alty free 3d model cellphone for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1481226)
turbosquid
$59
Cellphone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
Cellphone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
Cellphone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
CellPhone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
cellphone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
cellphone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Cellphone
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Sonim Cellphone
...ee 3d model sonim cellphone for download as 3ds, obj, and c4d on turbosquid: 3d models for games, architecture, videos. (1259074)