Thingiverse
XaxisClamp by rickswirebox
by Thingiverse
Last crawled date: 3 years, 1 month ago
I had a loose X-axis rod that would not keep my end-stop set, which is clamped on it. So i jumped on the Cad program and worked up this clamp. Works great, even with out a screw. I may add one later just for looks.
May want to file just a little on it for a perfect fit. A bit too tight on the X-axis carriage. I just used mine as is, but may later file it just a tiny bit.
Hope this helps someone else.
Happy 3D printing, Rick.
May want to file just a little on it for a perfect fit. A bit too tight on the X-axis carriage. I just used mine as is, but may later file it just a tiny bit.
Hope this helps someone else.
Happy 3D printing, Rick.
Similar models
thingiverse
free
Small block for clamping X-Y axis by Gerrit3D
...clamping the x and y axis seemed a bit thin. i drew a quick new one with smal inlay for the nut so the tightening is pretty easy.
thingiverse
free
Z axis probe holder for solidoodle by mikegi
...spring) to clamp to the x-axis rods.
just fits between the belts. the smaller part could be a bit thinner in the next revision.
thingiverse
free
Prusa Mendel Z axis smooth rod clamp by Reuben
...y to clamp the other end of the smooth rod on the upper section.
i just did a little editing of the ancestors to make this thing.
thingiverse
free
Beefed up Extruder unit for the MakerGear M2 and E3D Hot End by Zeeflyboy
...the stl, the other is with mesh mixer supports baked in. it worked brilliantly for me so thought i'd include the option here.
thingiverse
free
Gen4 Cupcake Lowrider X axis endstop mount by Zh4x0r
...luding content center parts, like the nuts n bolts) are here, and should be able to load fine by opening the project in inventor.
thingiverse
free
Creality Ender 3 V2 Belt Tensioner Cover by bspoel
... tight on the y axis. with a little bit of trimming, i was able to get it to fit for the y axis belt tensioner. hope you like it!
thingiverse
free
shapeoko X axis belt clamp by LineKernel
...shapeoko x axis belt clamp by linekernel
thingiverse
3d printed x axis belt clamp
thingiverse
free
Prusa MK3 Bear X-End for Purge Mechanism
...venting the mechanism from working is not with this remix, i will leave it up in the event a solution can be found in the future.
thingiverse
free
Makes printrbot original a bit faster, belt tightener for x-axis - I use it with GT2 aluminium pulley, original should work also by schrotti
... gt2 aluminium pulley.
i use two m3 - 30 screws with stop nuts.
for y-axis i use this : http://www.thingiverse.com/thing:121101
thingiverse
free
HTD3 Belt Clamp by Jeepguy42
...elts to prevent the belts from sliping out of the mdf clamps. after printing just line them up and drill some holes through them.
Rickswirebox
thingiverse
free
Clock-Dial-Floating by rickswirebox
...dial-floating by rickswirebox
thingiverse
5-3/4 inch diameter round with 1/2 inch numbers.
may be glued to most anything.
enjoy.
thingiverse
free
BreadBagClip by rickswirebox
...
update: check out the tator-chip-bag-clip, works great, it's here: http://www.thingiverse.com/thing:172376 thanks, rick.
thingiverse
free
Ipad/Tablet palm rests by rickswirebox
... notes or draws on tablet/ipad needs one of these or both.
makes note taking and drawing a breeze.
thanks, happy printing. :) .
thingiverse
free
Sandwich-Pack by rickswirebox
...top should slip right over the bottom and push down on the sandwiches keeping them ready to eat.
enjoy, happy printing....... :)
thingiverse
free
Mini_Squares by rickswirebox
...ed mine with 2, o.k but not perfect like i like. 26 minutes to print. easy cad to draw, don't get any easier.
enjoy, rick.
thingiverse
free
Small_Center_Square by rickswirebox
... square edges and hold/push the thumb support square while it hardens. just a thought.
mine printed well, hope you enjoy, rick.
thingiverse
free
PowerSupply_NameTags by rickswirebox
...as i did.
p.s. the middle part makes a great glue stick as well....... :) you can see i don't throw nothing away.........
thingiverse
free
Tator-Chip-Bag-Clip by rickswirebox
...omes through, here's the latest on my bread bag clip, find it here: http://www.thingiverse.com/thing:177088 thanks, rick.
thingiverse
free
12 inch Craftsman Bandsaw Blade Gaurd by rickswirebox
...in.
you may need to run a pocket knife around the edge just a bit for a tight, snug fit, but i like mine tight.
enjoy, rick.