Thingiverse
Coronavirus Ornament 2020 by sinned6915
by Thingiverse
Last crawled date: 3 years, 4 months ago
Comemorate your holiday with a snowball Corona Virus Ornament 2020!
Relieved to conserve filament, this slide together ornament assembles into your very own snowball model of the coronavirus Sars-Cov-2, which causes COVID-19. While the real virus has 74 spikes, this only fewer for simplicity.
Wear your mask, practice good hygiene, love you neighbor. Support you local merchants. Keep the front line workers in your thoughts this holiday season. They are the ones keeping us alive.
Initial Release: 4 blades.
Rev01: Increased size, made protien spikes more printable, chamfered edges, fixed clearance issues with Part B.
Rev02: Added 3-Blade.
Rev03 : meh
Rev04: 2 color parts. Slightly thicker parts for the peg holes and pegs for a 2 color print. The holes are heagons so no internal supports needed.
The pegs also are also hex shaped and smaller than the holes with chamfered edges. This is a fussy part- your slicer settings need to dead on for the clearances and chamfers to make this a snap togther part. Dont be surprised if you need to touch up the ends of the pegs with a file or emery board to make them fit. A 2mm or 5/64 drill can be used to clean up the hex holes if need be.
Relieved to conserve filament, this slide together ornament assembles into your very own snowball model of the coronavirus Sars-Cov-2, which causes COVID-19. While the real virus has 74 spikes, this only fewer for simplicity.
Wear your mask, practice good hygiene, love you neighbor. Support you local merchants. Keep the front line workers in your thoughts this holiday season. They are the ones keeping us alive.
Initial Release: 4 blades.
Rev01: Increased size, made protien spikes more printable, chamfered edges, fixed clearance issues with Part B.
Rev02: Added 3-Blade.
Rev03 : meh
Rev04: 2 color parts. Slightly thicker parts for the peg holes and pegs for a 2 color print. The holes are heagons so no internal supports needed.
The pegs also are also hex shaped and smaller than the holes with chamfered edges. This is a fussy part- your slicer settings need to dead on for the clearances and chamfers to make this a snap togther part. Dont be surprised if you need to touch up the ends of the pegs with a file or emery board to make them fit. A 2mm or 5/64 drill can be used to clean up the hex holes if need be.
Similar models
thingiverse
free
First Pandemic 2020 Ornament by DisBeRay
...e to keep together or edit it to make your own message, or print as one piece and paint. either way, have fun with it and enjoy!
thingiverse
free
Covid-19/Coronavirus Christmas Ornament by joshedges
...prusa mini.
i included some of the pictures i used as i was designing the model.
good luck all! post pictures if you make it!
thingiverse
free
Covid-19/Coronavirus Christmas Ornament by joshedges
...the prusa mini.
i included some of the pictures i used as i was designing the model.
good luck all! post pictures if you make it!
thingiverse
free
2020 Coronavirus Ornament by CrazyChocolatier
...arts one after another. depending on your 3d printer, there may be a little stringing between the proteins on the virus ornament.
thingiverse
free
2020 SUS Holiday Ornament by GRouNDzZeRo
...n need of some cheering up for the 2020 holiday season
using a flat profile for ease of mailing inside of a holiday greeting card
thingiverse
free
Teacher Pencil Ornament - 2 Sided by Sparrowz
...arance and they went in with a little force. if your printer has a lot of elephant's foot, you may need to lessen the radius.
thingiverse
free
Wood chamfer tool 45° edge plane by sch00f
...-2mm chamfer.
prints easily in one piece, activate supports on build plate only (for the center hole).
v2 now has a tilted blade.
thingiverse
free
Coronavirus COVID-19 2020 Christmas Ornament by SirAngusSteele
... was inspired by this other beautiful christmas ornament that you should also check out.https://www.thingiverse.com/thing:4653859
thingiverse
free
Offset 30mm to 40mm fan shroud conversion by blackhawk0258
... you are using
3 m3x12 to attach the conversion to your existing part
update 9/21/2020: enlarged holes for easier screw clearance
thingiverse
free
Holiday Ornament Ground Spike by 3Dd_Printing_N_Design
...n_design
thingiverse
this is specifically for the lit up candy canes, its the spike that goes into the ground that break easily.
Sinned6915
thingiverse
free
i3 OEM Thumbwheel cover by sinned6915
...e weight and feel of the oem thumbwheel over the thin wheel with lock nut insert. remixed with openscad source and ms 3d builder.
thingiverse
free
LED Indicator bar by sinned6915
...al to tone down the brightness.
the screw holes are pilot hole sized for the original m3 screws that mounted to the fan bracket.
thingiverse
free
Wanhao Duplicator i3 Cable Grommet Rear Rail by sinned6915
... zip tie holding the existing wires in place, move down and slide grommet into place. install a new zip tie to secure everything.
thingiverse
free
OBDII Break Out box by sinned6915
...oles sized for big box store gardner bender grommets.
print it out, zippity zappity, bob is not uncle, now he's your bitch!
thingiverse
free
Powerstroke Oil Pan Bung Wrench by sinned6915
...ll.
wes did a good overview of fixing his truck, musch better than i could have done.https://www.youtube.com/watch?v=onqrhkuo2z4
thingiverse
free
Extrusion Calibration by Calipers by sinned6915
...y for the major firmware flavors. if you are not using already, you should, and if you are, throw a few duckets gina's way...
thingiverse
free
Fabrikator Mini 1.5 Multi-Fan base by sinned6915
...the larger ones.
mi mini is quite happy with a 12v 70mm cpu fan, and it is quiet!
not all fans sizes have been tried/fit, ymmv.
thingiverse
free
Tuna Can Parts Washer by sinned6915
... umph than petg.
use a piece of filament as a rivet to clinch the basket springs together- see assembly illustrations in photos.
thingiverse
free
Tinyboy / Fabricator Mini 1.5 Part Cooling Fan by sinned6915
... on your additional fan, you might have to trim the fan duct a bit to get it to fit. the center tab should hold the fan in place.
Coronavirus
3d_export
$5
coronavirus
...coronavirus
3dexport
coronavirus
3d_export
$10
coronavirus
...coronavirus
3dexport
3d model of coronavirus
turbosquid
$10
Coronavirus
...s
turbosquid
free 3d model coronavirus for download as blend on turbosquid: 3d models for games, architecture, videos. (1644608)
turbosquid
$8
coronavirus
...urbosquid
royalty free 3d model coronavirus for download as on turbosquid: 3d models for games, architecture, videos. (1537371)
3d_export
$5
coronavirus covid19
...coronavirus covid19
3dexport
coronavirus covid19
3d_export
$10
coronavirus
...coronavirus
3dexport
content:
turbosquid
$10
coronavirus
...quid
royalty free 3d model coronavirus for download as blend on turbosquid: 3d models for games, architecture, videos. (1516737)
turbosquid
$10
coronavirus
...osquid
royalty free 3d model coronavirus for download as c4d on turbosquid: 3d models for games, architecture, videos. (1550881)
turbosquid
$10
Coronavirus
...osquid
royalty free 3d model coronavirus for download as max on turbosquid: 3d models for games, architecture, videos. (1516736)
turbosquid
$5
Coronavirus
...quid
royalty free 3d model coronavirus for download as blend on turbosquid: 3d models for games, architecture, videos. (1627449)
Ornament
3ddd
$1
ornament
...ornament
3ddd
ornament
3ddd
$1
Ornament
...ornament
3ddd
барельеф
ornament
3ddd
$1
ornament
...ornament
3ddd
gold ornament
3d_export
$5
rose ornaments
...rose ornaments
3dexport
rose ornaments rose ornaments
turbosquid
$2
Christmas Ornament Christmas Ornament
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Ornament
...ornament
3ddd
узор
turbosquid
$6
ornament
...urbosquid
royalty free 3d model ornament for download as max on turbosquid: 3d models for games, architecture, videos. (1669158)
turbosquid
$5
ornament
...urbosquid
royalty free 3d model ornament for download as stl on turbosquid: 3d models for games, architecture, videos. (1370327)
turbosquid
$5
Ornament
...urbosquid
royalty free 3d model ornament for download as max on turbosquid: 3d models for games, architecture, videos. (1507987)
3d_export
$10
modern ornaments
...modern ornaments
3dexport
modern ornaments
2020
3d_export
$5
cyberpunk 2020
...cyberpunk 2020
3dexport
cyberpunk 2020
3d_export
$5
monster01 2020
...monster01 2020
3dexport
monster01 2020 dxf file rigged in mixamo.
3d_export
$129
explorer 2020
...explorer 2020
3dexport
3d_export
$5
mug 2020
...mug 2020
3dexport
3d_export
$15
3 rims 2020
...3 rims 2020
3dexport
new rims 2020 from inventor
turbosquid
$7
Keepsake of 2020
...ty free 3d model keepsake of 2020 for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1657350)
3d_export
$35
landrover 2020
...landrover 2020
3dexport
turbosquid
$15
Timeless 2020
...free 3d model timeless 2020 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1433362)
turbosquid
$85
Q8 2020
... free 3d model audi q8 2020 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1559582)
turbosquid
$59
Supra 2020
...ee 3d model supra 2020 for download as max, lwo, obj, and c4d on turbosquid: 3d models for games, architecture, videos. (1404492)