14 sinned6915 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
i3 OEM Thumbwheel cover by sinned6915
...e weight and feel of the oem thumbwheel over the thin wheel with lock nut insert. remixed with openscad source and ms 3d builder.
thingiverse
free
LED Indicator bar by sinned6915
...al to tone down the brightness.
the screw holes are pilot hole sized for the original m3 screws that mounted to the fan bracket.
thingiverse
free
Wanhao Duplicator i3 Cable Grommet Rear Rail by sinned6915
... zip tie holding the existing wires in place, move down and slide grommet into place. install a new zip tie to secure everything.
thingiverse
free
Coronavirus Ornament 2020 by sinned6915
...s of the pegs with a file or emery board to make them fit. a 2mm or 5/64 drill can be used to clean up the hex holes if need be.
thingiverse
free
OBDII Break Out box by sinned6915
...oles sized for big box store gardner bender grommets.
print it out, zippity zappity, bob is not uncle, now he's your bitch!
thingiverse
free
Powerstroke Oil Pan Bung Wrench by sinned6915
...ll.
wes did a good overview of fixing his truck, musch better than i could have done.https://www.youtube.com/watch?v=onqrhkuo2z4
thingiverse
free
Extrusion Calibration by Calipers by sinned6915
...y for the major firmware flavors. if you are not using already, you should, and if you are, throw a few duckets gina's way...
thingiverse
free
Fabrikator Mini 1.5 Multi-Fan base by sinned6915
...the larger ones.
mi mini is quite happy with a 12v 70mm cpu fan, and it is quiet!
not all fans sizes have been tried/fit, ymmv.
thingiverse
free
Tuna Can Parts Washer by sinned6915
... umph than petg.
use a piece of filament as a rivet to clinch the basket springs together- see assembly illustrations in photos.
thingiverse
free
Tinyboy / Fabricator Mini 1.5 Part Cooling Fan by sinned6915
... on your additional fan, you might have to trim the fan duct a bit to get it to fit. the center tab should hold the fan in place.
thingiverse
free
7.3L Engine Sensor & Injector Break Out Box by sinned6915
...s should slide on the switch posts snuggly and friction fit on there.
after a little work, zippity-zappity, bob's yer bitch.
thingiverse
free
Buster Beagle PID Case Remix by sinned6915
...ve attached screenshots how i did it in superslicer/ prusa slicer (don' t ask me about how to do it in cura, i dont use it).
thingiverse
free
7.3L Enginer Sensor Break Out Box Injector cut our by sinned6915
...should be a snug fit on the switch posts.
swtiches are latching type, so depressing them break all contact until you unlatch it.
thingiverse
free
7.3L Powerstroke (Navistar/IH) Break Out Box by sinned6915
...nger to get the box into a more reasonable location. the box makes working on your truck solo much easier and stress free.
ymmv.