Thingiverse
Ai3MS Printhead Hotend cable strain relief by benspawn
by Thingiverse
Last crawled date: 3 years, 4 months ago
Anycubic i3 Mega S printhead cable strain-relief
I designed this because I did not find a simple cable strain-relief for the Anycubic i3 Mega S that didn't require an elaborate print. Also, I route my cable via the front instead of under the arch where it might pinch. in addition, I also gain a few millimeters in clearance when done this way. This is a simple and lightweight design that is sturdy. It serves its purpose without faff nor adding too much weight to your printhead. No extra hardware to needed besides cable ties. It's a clip-on design that uses friction and a tight fit to hold it in place. Also it is printed without supports needed. Orient this so it prints on its back.
INSTALLATION:
Remove your print head cover that holds the fans; this will be the two M3 screws on the top front, and another two M3 screws on the back near the bottom ball bearings.
Unplug your fans; paying attention to which plug each fan goes back into.
Unscrew the three M3 bolts holding the breakout board where the cable plugs into.
Lower the breakout board with the cable so you have enough space to clip the strain relief mount on. Push the mount all the way forward.
Push your cable back up and re-assemble everything in the reverse order that you removed them.
Zip-tie the cable through the zip-tie holes provided to secure and strain-relief the cable.
Thanks for looking and using this!
If you like my design, and are feeling generous, feel free to leave me a tip!
Check my page out for more designs as I continue to create stuffs!
Happy 3D-ing!
I designed this because I did not find a simple cable strain-relief for the Anycubic i3 Mega S that didn't require an elaborate print. Also, I route my cable via the front instead of under the arch where it might pinch. in addition, I also gain a few millimeters in clearance when done this way. This is a simple and lightweight design that is sturdy. It serves its purpose without faff nor adding too much weight to your printhead. No extra hardware to needed besides cable ties. It's a clip-on design that uses friction and a tight fit to hold it in place. Also it is printed without supports needed. Orient this so it prints on its back.
INSTALLATION:
Remove your print head cover that holds the fans; this will be the two M3 screws on the top front, and another two M3 screws on the back near the bottom ball bearings.
Unplug your fans; paying attention to which plug each fan goes back into.
Unscrew the three M3 bolts holding the breakout board where the cable plugs into.
Lower the breakout board with the cable so you have enough space to clip the strain relief mount on. Push the mount all the way forward.
Push your cable back up and re-assemble everything in the reverse order that you removed them.
Zip-tie the cable through the zip-tie holes provided to secure and strain-relief the cable.
Thanks for looking and using this!
If you like my design, and are feeling generous, feel free to leave me a tip!
Check my page out for more designs as I continue to create stuffs!
Happy 3D-ing!
Similar models
thingiverse
free
Anycubic i3 Mega cable holder (printhead cables) by tarmogr
... threaded hole for mounting.
only one m3 screw needed.
i use it for anycubic i3 mega s (i beleave it fits for non s version also)
thingiverse
free
AnyCubic I3 Mega Bowden Cable Clip by Bertilax
...ress the
tube into the small hole. you can disasmble the bowden tube on the
extruder site too, to push the tube through the hole.
thingiverse
free
Cable strain relief for i3 by richard_j_m
...rd_j_m
thingiverse
use some braided sleeving (look on ebay) and zip clip over the top to take the strain off your control board.
thingiverse
free
Anycubic I3 Mega Bearing Retention Clip by tk6831
... out of the carriage housing so i designed this clip to keep it centered and captured. uses two small tie wraps to hold in place.
thingiverse
free
Wanhao D6 Printhead Cable management Zip-tie Clip by PapaGolfDesigns
...g in the back of the printer moving from right to left. this keeps the cables close to the head and secure.
printed in ngen flex.
thingiverse
free
Anycubic Mega Printhead Cable Hook From Teflon Tube
...des some flexibility and gives the wire some free space to extend or band. and the cable bands better while the printhead moving.
thingiverse
free
Anycubic i3-Mega Schutz Z-Achse by Jerks
...e frame of the anycubic i3 mega to prevent the cables etc. of the printhead get stuck on the z-axis or get stuck under the frame.
thingiverse
free
anycubic i3 mega fan back mount clip by ZaetSorn
...t the partcoolingfanshroud https://www.thingiverse.com/thing:351280 to an anycubic i3 mega from behind. (extralong shroud needed)
thingiverse
free
Wanhao duplicator i3 heatbed cabling strain relief by szabon
... slide back freely without colliding into the printer's frame.
the cable is fastened to the strain relief with a 3mm zip tie.
thingiverse
free
Anycubic Mega Cable Holder Left Base by 11JE11
...11
thingiverse
cable holder for anycubic mega s and i3.
base left
this protects the cables. there is less strain on the cables.
Benspawn
thingiverse
free
Ai3MS Hotbed Cable mount by benspawn
... extrusion and still figuring out this brand new roll of pla for a new manufacturer that i'm using. overall part fit is good.
thingiverse
free
Wire beak holder by benspawn
...s, feel free to leave me a tip!
check my page out often for more designs as i continue to create and design stuffs!
happy 3d-ing!
thingiverse
free
Anycubic i3 Mega S Bowden coupler M10 x 1.0 by benspawn
...s, feel free to leave me a tip!
check my page out often for more designs as i continue to create and design stuffs!
happy 3d-ing!
thingiverse
free
Anycubic i3 Mega S X carriage belt tensioner (NO MODIFICATIONS) by benspawn
...e feeling generous, feel free to leave me a tip!
check my page out for more designs as i continue to create stuffs!
happy 3d-ing!
Ai3Ms
thingiverse
free
AI3M S Extruder Gear by gadroli
...ai3m s extruder gear by gadroli
thingiverse
anycubic i3 mega s extruder gear
thingiverse
free
AI3M Düsenlüfter mit 80mm LED Ring
...ai3m düsenlüfter mit 80mm led ring
thingiverse
die quelle liegt by pizdeath.
thingiverse
free
Ai3M stepper driver fanduct
...hat are even more quiet and cost less than half of the noct(..) fans.
have fun printing and enjoy the quietness of the ai3m! :-)
thingiverse
free
Ai3M Piranha Belt-Mount
...
it is simply mounted on the original carriage by using one cable tie. centering is done by the part itself.
have fun printing!
thingiverse
free
Raspycam holder AI3M Anycubic I3 Mega
... mega
thingiverse
i think there is nothing important to tell.
it is just a fixed holder for a raspycam.
have fun with the thing.
thingiverse
free
Ai3M X Axis cable chain by TreeTolber
... x axis cable chain and necessary attachment pieces. the image above outlines all the parts to print and direction for assembly.
thingiverse
free
Board suporte AI3M SKR 1.4 by pedrocas
...ead, i change to skr 1.4 turbo with tft24 and tmc2208, learning firmware and implanting components. hope this will finish good :)
thingiverse
free
Ai3M - Fan Modification with Alternate Logo
... results printing both parts without support. (also pictured: "40mm adeptus mechanicus symbol fan guard" by asmodias)
thingiverse
free
Ai3M NEW cooler fan design backwards mounted
...,5mm diameter, so you can cut an m3 thread into it after printing.
have fun printig and enjoy the new quietness of the ai3m. :-)
thingiverse
free
support for Anycubic AI3MS Filler Filament Holder by stef_ladefense
...
adapter for the metal support of the mega s
print on a flat bottom with minimal support
you can modify with source on fusion360
Printhead
3d_export
$24
mechanical spider
...to 3d-print complex structures using its integrated spool and printhead it can also be used for all your mechanical...
thingiverse
free
Ultimaker printhead cover by Gijs
...ultimaker printhead cover by gijs
thingiverse
printhead cover to protect the wires on top of the ultimaker printhead
thingiverse
free
Modified printhead clamp by Striffster
... the part that sits on the carriage to make it easier to change printhead. fits http://www.thingiverse.com/thing:793689 carriage.
thingiverse
free
full printhead by bouverat3dprint
...full printhead by bouverat3dprint
thingiverse
printer wanhao 5s. filament ø3mm
thingiverse
free
101hero printhead carrier e3d by workshoptinkerers
...or a 4mm push-fit pneumatic fitting with m6 threads if a non bowden printhead was purchased.
added carrier for e3d v5 printheads.
thingiverse
free
Diamond 3-1 printhead home bracket by robmink
...ngiverse
use to level your bed. only use while the printhead is cold. i used this for the chinese knock off diamond printhead.
thingiverse
free
FLSUN Cube Dual printhead Mount remix by ReneDriessen
...flsun cube dual printhead mount remix by renedriessen
thingiverse
dual printhead carriage for flsun cube
thingiverse
free
Fan-duct E3d Printhead by Straub
...e3d printhead.
the duct is designed for a 12v radial fan who is used in mankati printers.
(manufacturer number: bfb04512hha-dv52)
thingiverse
free
Voron Cablechain Printhead by 3d-workshop
... compartment to store the printhead-connectors.
unfortunately all parts need to be printed with supports except the chain itself.
thingiverse
free
Anycubic Predator effector for Stoneflower3D printhead v2
...flower3d printhead v2
thingiverse
anycubic predator effector to use with stoneflower3d printhead kit v2 for 3d ceramic printers.
Strain
turbosquid
$85
Zeke strain
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Skimmer 3D Model
...skimmer 3d model archive3d skimmer perforated spoon strainng spoon skimmer - 3d model (*.gsm+*.3ds) for interior 3d...
archive3d
free
Skimmer 3D Model
...skimmer 3d model archive3d perforated spoon skimmer strainng spoon skimmer - 3d model (*.gsm+*.3ds) for interior 3d...
archive3d
free
Skimmer 3D Model
...skimmer 3d model archive3d skimmer perforated spoon strainng spoon skimmer 2 - 3d model (*.gsm+*.3ds) for interior...
archive3d
free
Skimmer 3D Model
...skimmer 3d model archive3d skimmer perforated spoon strainng spoon skimmer n160910 - 3d model (*.gsm+*.3ds) for interior...
archive3d
free
Skimmer 3D Model
...skimmer 3d model archive3d perforated spoon skimmer strainng spoon skimmer n070808 - 3d model (*.gsm+*.3ds) for interior...
archive3d
free
Skimmer 3D Model
...skimmer 3d model archive3d skimmer perforated spoon strainng spoon skimmer 2 n301007 - 3d model (*.gsm+*.3ds) for...
3d_export
$40
Influenza virus 3D Model
...h5n1 swine avian bird biology disease medical rna dna strain lipid cutaway section viral schematic infection protein cold electron...
3d_ocean
$12
Multistage water filter Aqua
...displacement draining filter filtering filtration multistage percolation pulution pure strainng water vray materials, lightning and scene setup included in...
3d_export
free
mushroom vase
...flower (in original scale), in every stalk there is strain to conduct extra water and keep this water in...
Hotend
thingiverse
free
hotend by fablab_lueneburg
...hotend by fablab_lueneburg
thingiverse
hotend model
thingiverse
free
Hotend for Graber
...hotend for graber
thingiverse
hotend complement pastes for graber printerhttps://youtu.be/0koxhnsuhdy
thingiverse
free
Hotend adapter by antaviana
...hotend adapter by antaviana
thingiverse
hotend adapter
thingiverse
free
hotend fan by mming1106
...hotend fan by mming1106
thingiverse
hotend fan
thingiverse
free
Hotend schema by ione
...hotend schema by ione
thingiverse
hotend project schema
thingiverse
free
Fabtotum XY Hotend holder for E3D Hotend
...s with integrated supports.
more for the project you can see here: https://kf-designs.com/2019/09/07/fabtotum-printer-conversion/
thingiverse
free
HotEnd Stand by onepointdiy
...tend, when you make your new hotend or repair your j-head or mg-plus hotend.
the hole of 16mm, please adjust using a reamer, etc.
thingiverse
free
fast magnetic hotend changer for Chimera Hotend by Draman
...chimera hotend !
and new basis (the hole from original is to small)
it is a remix form skimmy's fast magnetic hotend changer
thingiverse
free
Hotend Fan Adapter for MicroSwiss All Metal Hotend by jo_schi_man
...
thingiverse
little change for the hotend fan adapter to hold the microswiss all metal hotend (slightly longer and sharp edges).
thingiverse
free
Merlin Hotend by Alejanson
...merlin hotend by alejanson
thingiverse
this is a 1:1 drawing of the classic merlin hotend.
Relief
3d_export
$20
relief
...relief
3dexport
relief
turbosquid
$1
Relief
...
turbosquid
royalty free 3d model relief for download as obj on turbosquid: 3d models for games, architecture, videos. (1438537)
3d_export
$15
horse relief
...horse relief
3dexport
horse relief
3d_export
$10
jesus relief
...jesus relief
3dexport
jesus relief
3d_export
$10
rome relief
...rome relief
3dexport
rome relief
3d_export
$10
fish relief
...fish relief
3dexport
fish relief
3d_export
$10
eagle relief
...eagle relief
3dexport
eagle relief
3d_export
$10
eagle relief
...eagle relief
3dexport
eagle relief
3d_export
free
3d relief
...3d relief
3dexport
3d relief
turbosquid
free
Relief
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Cable
3d_export
free
Cables
...cables
3dexport
cables for your purposes
3d_export
free
cable belt for cable organization
...ze your cables in 3d printers. it will bend only to one direction. the area to put the cables per piece is aprox. 1,6cmx2,6cmx1cm
3d_ocean
$16
Ethernet Cable
...ethernet cable
3docean
cable computer electronics ethernet internet network connected
ethernet cable 3d model
3d_export
$65
cable
...cable
3dexport
simple rendering of the scene file
turbosquid
$14
Cable
...l cable for download as ma, max, fbx, 3ds, gltf, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1631358)
3ddd
$1
Cable Cover
...cable cover
3ddd
кабель
vertebra passacavo - cable cover
max + vray 2.20.03
3d_export
$15
Cable reel
...without cable. textures 4k 4096x4096 targa, png, jpeg.<br>number of polygons without cable: 2896<br>with cable: 35328
3d_export
$7
short cable
...short cable
3dexport
rubber cord. very detailed. cable thickness: 2.55 mm total length: 55mm
3d_export
$5
USB CABLE
...usb cable
3dexport
turbosquid
$30
Cable Reels
...osquid
royalty free 3d model cable reels for download as fbx on turbosquid: 3d models for games, architecture, videos. (1439507)