thingiverse

free

Wanhao d7 new limit switch 3D print model by Pmax75

...a mechanical end stroke instead of the optical one. https://www.cgtrader.com/3d-print-models/hobby-diy/mechanical-partswanhao-d7-new-limit-switch ...

thingiverse

free

Wanhao Duplicator 7 (D7) mask test by TORROR

...mask for wanhao duplicator 7. for more info you may follow to http://3dtoday.ru/blogs/torror/how-to-cure-chinese-part-3-new-mask/

thingiverse

free

Y motor mount Wanhao i3 Plus and similar

...i decided to print a new one i used longer m3 screw (double lenght or more of the original ones) and 2 m3 nut to secure in place.

thingiverse

free

directed Fan outlet for the D9 from Wanhao by dysseus

...version with the new printerhead. weight about 6g, same as the original part. edit: correctet the angle. have not printed it yet.

thingiverse

free

3MM Easy Snap together Bed Leveling Knob for Malyanm150/Wanhao i3 and Monoprice Select by DaakTwo

...m150,wanhao i3 and monoprice select, it is a 2 parts system with a hexagon pocket inside to put the...

thingiverse

free

Z-Axis Mod for Wanhao i3 Duplicator by BurulaNikita

...in some places, drilled extra bolt holes. all metal parts of the printer left in their places. gain cut...

thingiverse

free

E3D v6 mount for Wanhao i3 - version 2 by slimc

... found here http://a360.co/2nysyq6 a part for cooling the filament is under development and will be uploaded once it is finish :)

thingiverse

free

Raspberry Pi 2 Case with Camera Mount for Wanhao i3 Duplicator by cyul

...nted top. some might think i am obsessed with honeycomb. 20160503 - new bottom part. camera attachment set lower to avoid braces.

thingiverse

free

X-carriage for Flex3Drive for wanhao duplicator, malyan m150 and similar i3 clones by BogdanKecman

...ng of the extruder interesting note, the 50% infill printed part in abs is still noticeably lighter then original iron bracket :d

thingiverse

free

Gear Spinner by Mosaddak

...- 6 mm in diameter ... when you combine parts you may need some...

thingiverse

free

Wanhao Dup[licator 4S improvements by androot

...very stable. rod mounts are printed new, because original parts are very fragile and was cracked. last part is...

thingiverse

free

Ver2 : Anti-Vibration Feet for Makerbot / Wanhao / Ultimaker etc by AndyGadget

...extended the inners of the upper and lower foot parts and changed the recommended length for the rear tubes....

thingiverse

free

Wanhao Duplicator i3 / Monoprice Maker Select V2 Upgrade Part 2 - X-Axis another 30mm by OlafB

...a 30mm spacer to the x-axis without any new parts must be bought. this can be done by removing...

thingiverse

free

Wanhao Duplicator i3 120mm PSU Cover Insert by Cheesecycle

...s part to cap off the existing hole. it has a little tab that should snap into place. print with the larger flat side face down.

thingiverse

free

SWD3 KIT Z-AXIS REAR MOUNT FOR WANHAO DUPLICATOR I3 PLUS / MONOPRICE MAKER SELECT PLUS by ShadowWeaver2067

...lot of resources for this style of printer.http://3dprinterwiki.info/ for partsprinters and just about anything you can imagine wanhao visit...

thingiverse

free

Wanhao flexible extruder plate (lost PLA casting) by FilamentCorner

...this way you can move from plastic to metal parts here is a link to our video were we...

thingiverse

free

Wanhao Duplicator 4 (Makerbot) X axis stepper motor fan holder (with cable channel) by csatti

... to mount the part to the motor as well (no chance for falling down anymore), there is also a new cable channel connection point.

thingiverse

free

WANHAO DUPLICATOR D9 400 x axis extruder plate by bubu1882

...n of the d9 mk2 waggster firmware v1.0 software wanhao duplicator d9 400 bltouch brackethttps://www.thingiverse.com/thing:4260266

thingiverse

free

Palette+ sensor holder for Wanhao Duplicator 6 by Muratore73

...i used ca for this job. printing two separate parts eliminates the use of supports. the sensor-holder itself, is...

thingiverse

free

Wanhao Duplicator 6 Replacement X-Axis Limit bumper by NearFarMedia

...il! i've supplied step and rhino 3d (.3dm) files so you can remix and stuff if needed. just be cool and credit me somehow. :)

thingiverse

free

wanhao D6/D6 Plus Bondtech extruder board base upgarde by alptech

... wanhao d6 extruder kit btt smart filament sensor octopi - controller. slicer: cura 4.9.1 i have attached slicer profile as well.

thingiverse

free

ReDuplicator i3 MK3x - MK52 Removable Heatbed Expansion

...requires new extrusions and rods. some extrusions and printed parts are carried over from the original reduplicator...

thingiverse

free

Monoprice Maker Select V2.1 Cooling Fan by Zeffer7

...as well as one solid piece for easy printing. parts you will need: 4 m3x20 screws 1 m4x25 screw...

thingiverse

free

HC-SR04 Ultrasonic Sensor Mount for Servo by educ8s

...an led which i didn't utilize in this tank. parts hc-sr04 sensor: http://educ8s.tv/part/hcsr04 sg90 servo: http://educ8s.tv/part/sg90 3d printing this...

thingiverse

free

FrankenCooler for Wanhao Duplicator I3 V2.1 (CiiiCooler+Mistral) by TheIrbis

...s fromhttps://www.thingiverse.com/thing:2121279 on the photos is ugly first version)))) new version is the same, just smoother)))

thingiverse

free

Echo Spot Adjustable Stand by ThaiDai

...an adjustable stand for the new echo spot. 5 parts to print. you'll need magnets (difficult to print...). magnets:...

thingiverse

free

Wanhao Duplicator i3 Extruder Fan Adapter 40mm to 60mm by Marius_Hugo

...p://www.thingiverse.com/thing:1448241 an ideal fan cover for the 60mm fan is found here: http://www.thingiverse.com/thing:1655833

thingiverse

free

Wanhao i3 120mm Fan Mount PSU Control Box Back Plate by wywywywy

...note that by default the ac socket is on the left, cable bundle on the right. mirror it in the slicer if you need them reversed.

thingiverse

free

ReDuplicator i3 MK3x - Titan Aero Mount by OmNomNomagon

...with a 1.5mm drill bit. the new required printed parts when upgrading from the mk10 extruder are the: front...

thingiverse

free

Sturdy Di3 v2.1 bracket for Thorped fan duct by xyzaxis

...fan shroud bracket for thorped's fan duct adjustable bltouch front mount for wanhao i3 mount for biqu heated bed mosfet board

thingiverse

free

Wanhao i3 Floating Display by JeEk

...does, i believe you are good. the stand (feet parts are optional. ideas for the future one idea i...

thingiverse

free

Wanhao i3 Extruder Upgrade by JanEriKKa

...to redesign the lever as well to make the parts fit. this work is inspired by several existing designs...

thingiverse

free

Wanhao i3 Sideways Filament Guide Ball with Bowden Tube by venegade

...or rubbing from the filament on any 3d printed parts i am using a separate spool holder with skateboard...

thingiverse

free

E3D Titan Aero mount for wanhao i3 by Chanceinator

...ents: 2x m4 nuts (for belt fastening) 4x 3mm spacers (printed) the images show the process of assembly, any questions please ask!

thingiverse

free

Makerbot/Createbot MK8-MK9-MK10 to E3D V6 Dual Extruder with Bowden by pegasocube

...like makerbot, wanhao, etc..). the kit consist of 3 parts plus the nema17 support for bowden. plus 2 fans...

thingiverse

free

Wanhao D4S Hinge Replacement by samrobmoe

...hence why i have also made some little locking parts which can be attached with an m5 bolt as...

thingiverse

free

Z Axis locators for Wanhao Duplicator 4x by claymore61

...i find them , i'll make / download new parts i noticed that one of my prints had a...

thingiverse

free

SWD2 KIT Z-AXIS REAR MOUNT FOR WANHAO DUPLICATOR I3 / MONOPRICE MAKER SELECT by ShadowWeaver2067

...lot of resources for this style of printer.http://3dprinterwiki.info/ for partsprinters and just about anything you can imagine wanhao visit...

thingiverse

free

Super Simple Belt Tensioner X & Y Axis Remix - Monoprice 3D Maker Select V2 and Wanhao by AdamBath

...base, for a more positive fit. i've printed these parts now in pla, petg, and abs. i wouldn't recommend...

thingiverse

free

Modifided Z Extensions with Spacers for Wanhao Duplicator i3, Cocoon Create, and Maker Select by woodycarson

...t extensions to eliminate supports and if you want the peg version and don't want to have to sand that area, use the spacers.

thingiverse

free

MKS SBASE Conversion kit for Monoprice Maker Select (Wanhao i3) by CidVilas

...plate to accomodate feedthroughs and a new glcd. additional parts needed: usb extender: https://amzn.com/b00h8rx780 o this is for breaking...

thingiverse

free

Z Brace Yourself - Alternate Straight Braces for Wanhao i3 by OmNomNomagon

...levels) update june 2017 added a number of additional parts to increase the rigidity of the printer. optional tower...

thingiverse

free

Y-Axis Idler Pulley Bracket for Wanhao/Powerspec Duplicator i3 by WaterOakDesign

...axil with better parts from mcmaster-carr. here are the parts 3693n110 - m6, 20 tooth pulley 92981a911 - 5...

thingiverse

free

Wanhao Duplicator 4X - Top cover plate for MK9 extruder by Vexelius

...se it as a permanent part of your printer, increase the infill to 20% and the solid layers to 10, both in the top and the bottom.

thingiverse

free

Kryten's Head #2 by JediJeremy

...hotends are easier to find these days than mk10 parts it's not quite as good as a real prusa...

thingiverse

free

MK9 bowden extruder by kharar

...the code update version 2: apparently the mk9 molded parts were redesigned by the manufacturer, so i had to...

thingiverse

free

Wanhao D6 Lubricator, Cleaner, New Version by AbsolutBeginner

...öffnen. nachtrag:noch mal verbessert, längere schlaucheinführung. since the other parts offered here were more or less useless, or the...

thingiverse

free

D6 LHS angled cooling fan by gzcwnk

...ttps://www.aliexpress.com/item/original-ad0424ub-g70-double-ball-bearing-cooling-fan-dc-24v-0-1a-4010-40-40-10mm/32807900543.html

thingiverse

free

Wanhao Duplicator i3 Plus - Logitech C920 Webcam - Mount by doctriam

...lds the two separate pieces together. assembly is really easy once you slide the pieces onto the undercarriage of the print bed.

thingiverse

free

Wanhao Duplicator i3 Adjustable Z-Axis Limit Switch Mount by rasarmg

...stock screws, was completely printable, and had no additional parts required. all of these goals have been met. however,...

thingiverse

free

Dyne's Wanhao Y-Carriage C920 Camera Mount & Adapter by Dyne

...on to unacceptable levels. an example of a timelapse recorded using this mount; the model being printed was v2 of my finial tetra

thingiverse

free

Wanhao Duplicator 4X Cooling Fan Duct by SmartBlug

...have issue with the back -- update 08/01/2015 -- added a photo that explains how to install v4-4 (same system for front and rear)

thingiverse

free

Wanhao - Monoprice i3 V2.1 Cobra Cooler for Stock Fan by Roll1990

...4 x 16mm allen head screw to mount, but you could use a hex screw or philips, all would work the same (philips might be easiest).

thingiverse

free

LM8LUU Bearing Blocks by chinkel

...always turn out too tight, so i typically design parts with ~0.2 to 0.3 mm extra clearance. this file...

thingiverse

free

Dual Z-axis alignment bars by Coder-Tronics

...nd away from the alignment bars using the positioning system via the on screen menu. 10) remove the alignment bars and your done!

thingiverse

free

Wanhao Duplicator I3 Bowden Extruder for E3D V6 / Clone by chanders

.../ heat shrink snips 3d printer to print the parts parts needed e3d v6 (j-head) hotend for 1.75mm comes...

thingiverse

free

Wanhao Duplicator 6 Filament Spool Holder with "roller" surface (no hardware needed) by disoculated

...when reaching around printer. all of the version 4 parts should work fine with the version 3 parts, so...

thingiverse

free

ReDuplicator i3 MK3x - Wanhao i3 Complete Aluminium Extrusion & Prusa Mk3 Overhaul by OmNomNomagon

...otherwise pla may work except for the extruder carriage parts if using abs please allow for a few percent...

thingiverse

free

Wanhao i3 M8 Spool Holder Upgrade Kit by NozzleClog

...v2. nothing extraordinary. since it's an in progress, all parts of the kit haven't been included yet. two parts...

thingiverse

free

SWD1 KIT Z-AXIS FOR WANHAO DUPLICATOR I3 / MONOPRICE MAKER SELECT by ShadowWeaver2067

...exist between both of the other two creations, these parts are completely rebuilt in inventor and checked against the...

thingiverse

free

Feet for Wanhao Duplicator 6 (WD6) Monoprice Ultimate by TheMakerRob

... we aren't applying force against layer interfaces). the ends are rounded in order to try to protect surfaces it may sit on.

thingiverse

free

Wanhao DI3 X Idler Upgrade by ftk1

...arriage, then tighten bolt as far as it will go until it is flush with the back of the carriage. 6) re-mount and tension the belt

thingiverse

free

High performance cooling assembly for Wanhao I3 Plus by Yeahdog05

...the regular i3. you'll need to download the main parts from the original thing i remixed from here: https://www.thingiverse.com/thing:2084339...

thingiverse

free

Wanhao Duplicator i3 Gantry Cover by NvigR8

...printing vertically with supports at least on the horizontal parts i would not let the software put supports in...

thingiverse

free

X Belt tensioner for Malyan M150 by BogdanKecman

...and trough that notch you can access the screw to tighten/loosen the x belt, exactly the same tensioning system like exist for y)

thingiverse

free

Wanhao i3 120mm PSU Fan Upgrade for Undermount by Grantisimo

...r to attach the cover to your psu case. screw holes aren't countersunk (just counterbored), so choose screws with a flat top.

thingiverse

free

Titan Aero for Wanhao I3 Plus with Belt Tensioner by AldiPrinter

...pcs m4 low profile nut (thickness ~ 3mm) printed parts carriage plate belt holder arm + base thorped arm...

thingiverse

free

Standoff for Heat Bed Power Module Expansion Board (MOSFET) for Monoprice Maker Select, Wanhao i3, Cocoon Create by rawlogic

...board, and so it is firmly screwed in place. parts needed (single mosfet board): 4 x m3x5mm 0.5mm pitch...

thingiverse

free

Heatbed cabling strain relief by Coder-Tronics

...tweaked the cable clamp so it interlocks, all new parts are labelled v4, the purple printed parts in the...

thingiverse

free

2in1 cooler for wanhao i3 v2 and cacoon create (abandoned) by FilamentCorner

...anted to create something for the wanhao community after all the help they gave me . test it out and let me know if its any good.

thingiverse

free

Wanhao I3 Plus/Maker Select Plus Titan Aero mount by m0214

...zip tie to hold the wires in place. additional parts required to be printed:https://www.thingiverse.com/thing:1394558 qty 1https://www.thingiverse.com/download:3442143 qty 2 note:...

thingiverse

free

BMG Extruder + V6 Hotend for Monoprice Maker Select (i3) by marshes

...knockoff if you're feeling lucky) 5015 blower for cooling parts bltouch v3 oem x rails + linear bearings/blocks oem...

thingiverse

free

Wanhao Duplicator i3 front blower fan mount and shroud by NvigR8

...blower fan mount and shroud by nvigr8 thingiverse these parts adapt a blower type fan for use on the...

thingiverse

free

Wanhao Di3 Cobra Fan Blower->40mm Adapter by shaiss

...less backflow or turbulance and more air on your parts i'm pretty confident i can significantly lower my pla...

thingiverse

free

Wanhao Duplicator i3 v2.1 / Monoprice Maker Select Bowden Kit (for bondtech mini or other bowden extruders)

...and extruder on first, then re-attach the cable chains. parts needed: 12+ inches of bowden tube 1x m6 4mm...

thingiverse

free

Thrustmaster hotas warthog flight stick Extension by No3DoB Reupload (More versions added!) by ServError

...9;t matter supports: yes resolution: .1 infill: 70% notes: support touching bed is needed, flip the lower thread part 180 degrees

thingiverse

free

Wanhao Duplicator I3 PVC Style Z-Brace and extras by carternick01

...dug and dug through countless files looking for ideals parts and these are the ones i ended up with....

thingiverse

free

Wanhao Duplicator I3 Complete frame rebuild in Lulzbot Taz 5 style by curiouscretin

...to completely strip my i3 all down to bare parts and rebuild it, so a lot can co wrong....

thingiverse

free

Wanhao Duplicator i3 120mm PSU Cover by Korzar

...de and secure the fan with a washer and a nut on the outside. make sure you don't use model b if you're going that route.

thingiverse

free

Wanhao i3 Plus/ Cocoon Create Touch X-axis ratcheting belt tensioner by martin_au

...the printer out of its enclosure for photographing the parts :d requires a 20 - 25mm m3 bolt and...

thingiverse

free

Wanhao Duplicator i3 Y Axis Pulley by Wasatch

... store's list of priorities (he'll probably read this -hopefully)https://www.3dhubs.com/salt-lake-city/hubs/wasatch-brian

thingiverse

free

M8 Linear bearing (LM8LUU Drylin Hybrid) by Coder-Tronics

...1-08 but this is a 45mm version. the image for this on the website shows 12 teeth, but when i looked at the drawing it shows 10!

thingiverse

free

2020 Y upgrade for Wanhao Duplicator i3, Cocoon Create, Maker Select, and Malyan M150 i3 3D printers. by delukart

...swd2 rear mounted z brace. i only uploaded the parts i modded and created. the rest of the parts...

thingiverse

free

Cooler for Wanhao Duplicator i3 stock fan by tahustvedt

...off easilly. the ones under the inlet are tougher to break off, but the finish is never going to be that good under there anyway.

thingiverse

free

X Axis Belt Tensioner for Wanhao i3, Monoprice Maker Select, Cocoon Create etc. by Heathicus

...should be able to print any of the above parts with no...

thingiverse

free

Filament guide for MK8 spring loaded aluminium arms for CTC Replicator Flashforge Dual (update: for flex) by 3DWorkhorse

...the new version under the name "2019_improved_filamentguide_flex" containing all parts needed. attention, the backplate is 0.7mm thinner now for...

thingiverse

free

bearing supported spool cradle with filament guide (fits Wanhao i3 built-in bolt holes) by Rexipus

...easier i've attached my solidworks source files for these parts i'm brand new to solidworks, and this is my...

thingiverse

free

Barnard S action. Dummy to use to trial fit stocks/chassis by gzcwnk

...update, 5/12/2017 added jewel trigger and barnard s hanger parts to assist trail fit. modded rear body to accept...

thingiverse

free

Wanhao D6 Left Fan Mount With Slide On Nozzle - Top Fixing by The3dRoom

... material and increase clearance. i've included 2 stl's for the new mount, one with supports included, the other without.

thingiverse

free

Wanhao i3 mini extruder mount ( e3d v6 ) by Garrett_w

...ould push over without too much difficulty i will probably refine this design later when i get more time and post updates to it.

thingiverse

free

Wanhao Duplicator 4S Y-axis pillow blocks & supports by WillMackey

...z-axis slide screws with m3x15 screw found in spare parts bag that came with the unit and install rear...

thingiverse

free

Wanhao i3 Backplate with Dual 50mm fans by Dracos

...(the stock fan is installed as intake). i have lots of airflow through the control box now, even with the mess of wiring inside.

thingiverse

free

Duplicator i3 Filament Stand by garrettreed

...the design so that it now prints in three parts a base and two sliders. the base mounts in...

thingiverse

free

Wanhao Duplicator i3 Y-Axis extension by retrofluffyboy

...a wanhao i3 duplicator. you will need the following parts for it: mk2a 300x200x3.0mm pcb aluminum heatbed if you...

thingiverse

free

Maker Select Plus Z-Axis Level Feet by TEN1964

...to level off the machine, hope my instructions and parts will be helpful to others, i am open to...

thingiverse

free

Monoprice Ultimate Blower Duct by JGTMaker

...t required and to improve the overall print results. thanks easyst and others who pointed this out. your feedback is appreciated.

thingiverse

free

Wanhao/Maker Select i3 Ramps Conversion for OSOYOO Ramps Kit with 2.8" Touch Screen by Jimbotron

...with touch screen using the kit linked above. the parts that i made include: mkstft28_adapter05.stl - this is the...

thingiverse

free

WANHAO Duplicator i3 Z-Axis extension by retrofluffyboy

...600mm cylinder liner rail linear shaft optical axis cnc parts http://www.aliexpress.com/item/new-8mm-l600mm-linear-shaft-od-8mm-x-600mm-cylinder-liner-rail-linear-shaft-optical-axis/32355714675.html?spm=2114.13010608.0.58.iawcts you will also need a about 30 m3...

thingiverse

free

Bowden Mount *new fan mount* CTC improved remix-v2. No Sensor mount. For CTC / Flashforge / Qidi Tech-I / Makerbot Replicator / Monoprice CTC / Wanhao Duplicator 4/ Generic Acrylic CTC by Gremble

...which is probably the highest difficulty of all my parts however, makerbots are a dime a dozen so this...

thingiverse

free

Active Cooling Fan Duct for Replicator 1 / Duplicator 4 / FlashForge by thruit00

... all trademarks mentioned belong to their respective owners. modification of your device might result in a full loss of warranty.

thingiverse

free

Longer Bowden Extruder and Filament Sensor Kit by RonnieG303

...this is a partially new, partially tested design. some parts have been tested and proven. some haven't, yet. you...

thingiverse

free

Wanhao Duplicator I3 Z Axis Camera Mount by Hollywood0967

...functional and gets the job done for me. -required parts 3 m3x12 screws 1 m3 nut 1 attachment point...

thingiverse

free

Wanhao Duplicator 9 D9 300 X Axis Bracket

...le gantry plates addon for y axis- https://www.thingiverse.com/thing:3906204 z braces - https://www.thingiverse.com/thing:3906124

thingiverse

free

ReDuplicator i3 MK3x - E3D Hemera Mount with Bltouch and Filament Sensor

...much easier to setup with sensorless homing. the printed parts should be a minimum of 3 perimeters and 20%+...

thingiverse

free

MJW Octopi Mount for Raspberry Pi Zero W with Camera - Wanhao Duplicator i3 / i3 v2 / i3 v2.1 / i3+ by MJWMakes

...3 x small pieces of heatshrink instructions: print all parts gather needed parts. install your raspberry pi zero w...

thingiverse

free

Toilet Paper Holder slide in slide out auto hold by Nerys

...thingiverse final pictures uploaded !!! final (i think) v4 parts uploaded. cleaned up as best i can too. i...

thingiverse

free

Monoprice Ultimate 40mm blower fan duct by sgiacci

...39;t use it, nor did i get any feed back from other users. so v7 is available, and hopefully i have most of the bugs worked out.

thingiverse

free

E3D v6 Bowden extruder for Wanhao Duplicator i3 by JonBAL

...screws (9-10mm) - 2pcs cold end i use: stock parts of mk10 kharar's mk9 bowden extruder - mk9_bowden.stl m3...

thingiverse

free

SF ASP Lightsaber Chassis - NEC/NBv3/CF/PC by ScarletImpaler

...system designed to hold electronics for saberforge adaptive saber parts lightsabers. how to read file names. for example "asp_nec_20mm_rcp"...

thingiverse

free

Wanhao i3 Plus enclosure with cooling by gadgetmind

...clamps didn't quite work as designed and the inner parts are probably all you need. i can upload the...

thingiverse

free

Bolt-On Bowden Mount For a Stock Monoprice Maker Select V2.1, Wanhao Duplicator i3 by ModifiedDesigns3D

...assembly (a little more complicated but simple) print your parts! lol there is a left and right motor mount...

thingiverse

free

Baby's Great Shape Puzzle by Javicom

...a few emissions during printing. i have successfully printed parts with prusament pla and extrudr petg. extrudr petg can...

thingiverse

free

Wanhao i3 Control Box Rear Panel for Modular Connections by emertonom

...as critical for the endstops and thermistors, as these parts don't require a specific orientation, but i kept it...

thingiverse

free

Wanhao Duplicator 6 Fan Duct (Improved Magnum: "Supermagnum") by Reflector

...in the legs of a triangle more or less. obviously you have more to lose if you stick anything like a heatsink onto your steppers.

thingiverse

free

Wanhao Duplicator 6 Air Inducement Duct by Reflector

...of recursion could occur. oh wait printing 3d printer parts with a 3d printer and all. have i mentioned...

thingiverse

free

Relay Control OctoPrint Wanhao i3 by Jeffeb3

...print can keep on doing whatever it was doing before calling that script, wihtout waiting for the sleep or the command to finish.

thingiverse

free

Filament Sample Card - Customizable SCAD by tkris_sd

...easier to read.. and hey, it works now too! if you downloaded the .scad file already, you might want to grab the updated version.

thingiverse

free

Open source bullet feeder / collator - 223/556 (Dillion 650, Hornady L&L etc) by gzcwnk

...source code files are provided allowing you to mod parts to suit your need. hence i will not be...

thingiverse

free

Canon Digital Lens Mount for JK Optical Printer

...oard and choosing a new orientation. notes: designed in freecad 0.18 printed in pla at 0.2mm resolution on a wanhao duplicator i3

thingiverse

free

GUST - i3 print cooler (Plus, v2.1, maybe others?) by WaveSupportApparatus

...ans sparking because they're over-volted, they will eventually fail and start making these horrible grinding/rattling sounds.