Thingiverse
OpenRC F1 Adjustable Steering by marcotheboy
by Thingiverse
Last crawled date: 3 years ago
This allows you to adjust the tracking on your OpenRC F1 car,
It also positions both steering arms at the same height (so one is not at an upwards angle like on the original design).
You need an M3 screw which you cut off the head and is screwed into both halves of the track rod (or is it tie-rod?).
To assemble it, screw half the M3 bolt into the inner rod and then cut its head off.
Round off the sharp edges with a file or Dremel and screw the outer rod onto it.
You could put some super-glue or threadlock in the inner rod first, since it is only the outer rod that will need to rotate.
There are 2 versions:
For the non-2017 car, you need 2 x 20mm to 25mm M3 screws. (The hole is 12.75mm deep.)
For the 2017 car, you need 2 x 20mm to 30mm M3 screws. (The hole is 15mm deep.)
To adjust the steering, disconnect the outer steering rod from the wheel and rotate it half turns until the tracking is correct.
The pictures show it with the front suspension mod, but it works exactly the same with the stock configuration.
If you want to print all 4 pieces at once, you can just download theSteering_TieRods_All_2017.stl or Steering_TieRods_All.stl file.
It also positions both steering arms at the same height (so one is not at an upwards angle like on the original design).
You need an M3 screw which you cut off the head and is screwed into both halves of the track rod (or is it tie-rod?).
To assemble it, screw half the M3 bolt into the inner rod and then cut its head off.
Round off the sharp edges with a file or Dremel and screw the outer rod onto it.
You could put some super-glue or threadlock in the inner rod first, since it is only the outer rod that will need to rotate.
There are 2 versions:
For the non-2017 car, you need 2 x 20mm to 25mm M3 screws. (The hole is 12.75mm deep.)
For the 2017 car, you need 2 x 20mm to 30mm M3 screws. (The hole is 15mm deep.)
To adjust the steering, disconnect the outer steering rod from the wheel and rotate it half turns until the tracking is correct.
The pictures show it with the front suspension mod, but it works exactly the same with the stock configuration.
If you want to print all 4 pieces at once, you can just download theSteering_TieRods_All_2017.stl or Steering_TieRods_All.stl file.
Similar models
thingiverse
free
OpenRC 4WD Truggy RC Car improved Steering Pin by Knese
... the openrc 4wd truggy rc car, had problems with jumping off steering pins.
you need two m3 (10mm) screws and nuts for each side.
thingiverse
free
OpenRc F1 front axle by nicklindenmuth
...e front hub with enlarged hole for a single steering bolt through the whole thing and steering endstops. uses two 25mm m3 screws.
thingiverse
free
Belt holder with tension adjustment by kfceric
...ead screw m3 x 40mm x 2 pcs
2020 m3 self lock nut x 4pcs
623zz bearing x 2pcs
m3 x 0.7mm washer x 5pcs
one printer need 3 sets
thingiverse
free
OpenRC F1 2017 Rear Axle Reinforced by Drazen
...larger to accept a #8 threaded rod. the hole runs the full length of the axle.
use a drill to help thread the rod into the axle.
thingiverse
free
OpenRC F1 Pushrod by rubenhak
... tightened to servo arm and modified front lower bom using m2.5 screws. screws should move freely inside servo arm and lower bom.
grabcad
free
F1 steering wheel - 3D printable
...e 30x12 (3mm dia, 12mm length)
use screws with wide heads (integrated disc) or use a washer if you have screws with small heads.
thingiverse
free
8mm rod mount for 2020 extrusion by joochung
...wide cylinder, you can rotate it to any orientation you need. put two of them on your 2020 frame and place an 8mm rod in between.
thingiverse
free
F1 Friction Damper by rhoagland
... damper by rhoagland
thingiverse
friction damper for use on openrc and hpd f1 cars.
mounting holes are designed for m3 hardware.
thingiverse
free
Tarmo4 Steering Range Adjustments (part 20B) by ratchet_hamster
...ith the rims if the mounting is set quiet far into the rim. if this is the case you could look into making the hex hub extendors.
thingiverse
free
1:10 RC Car outer tie rod by Cwalz
... sizes 4-4,1mm.
you might have to use grading tool and/or heat it up a bit to mount the part properly.
fits with m3 screw joints.
Marcotheboy
thingiverse
free
FPV Lens Cap 14mm by marcotheboy
...y camera with 14mm diameter lens.
it is printed in tpu and fits snugly.
the wide base makes it easy to grab when you pull it off.
thingiverse
free
Taller Control Horn by marcotheboy
...e cub ailerons.
it is 2mm thick.
the distance of the top hole to the aileron surface is 18mm.
the diameters of the holes are 1mm.
thingiverse
free
Pump Needle Adapter Holder by marcotheboy
...n to lose your needle adapter (for pumping footballs, etc).
it fits on 10mm diameter hose.
print in flexible filament (tpu, etc).
thingiverse
free
Viofo A119 Mount by marcotheboy
...are in a hot climate, it may be wise to print this in abs.
(i printed one in pla and it did not warp in the british summer heat.)
thingiverse
free
EV100 Battery Holder by marcotheboy
...his design holds onto the strap much more securely.
to insert the strap into the slot, it helps to stretch it while inserting it.
thingiverse
free
EV100 ProDVR Strap Mount by marcotheboy
...the slot, it helps to stretch it while inserting it.
i updated it to version 2: the strap is now in the middle (it looks nicer).
thingiverse
free
Tamiya Vanquish Front Upright by marcotheboy
...collision with a wall. this should be much stronger than the original. i printed it in pla at 20% infill and it is strong enough.
thingiverse
free
Filament Spool Holder by marcotheboy
...
if you don't have the bearings, you can print this 'dummy' bearing instead:https://www.thingiverse.com/thing:2085033
thingiverse
free
ZMR250 Mobius Mount by marcotheboy
...the stock m3x6 screws are just too short, so you should use m3x8 (or m3x10 to be safe).
(the thickness of the mount base is 2mm.)
thingiverse
free
Tamiya Vanquish FPV camera mount by marcotheboy
...//youtu.be/tpgpavs7ooe
(in the photo/video i am using a runcam micro swift 2 camera and runcam tx200u video transmitter on 25mw.)
Openrc
thingiverse
free
Battery holder for OpenRC by Wiero
...battery holder for openrc by wiero
thingiverse
battery holder for openrc
thingiverse
free
Front Wing OpenRC F1 by scarpantes
...front wing openrc f1 by scarpantes
thingiverse
front wing openrc f1
thingiverse
free
OpenRC f1 GoPro Mount by iClint
...openrc f1 gopro mount by iclint
thingiverse
pov mount for openrc f1 car
thingiverse
free
OpenRC F1 Bushings by rbrutsky
...openrc f1 bushings by rbrutsky
thingiverse
rear 12x18x4 bushings for the openrc formula 1 car. you must scale the bushings x10
thingiverse
free
OpenRC Truggy Trailer by Steamerzone
...verse
openrc truggy trailer with working suspension. the white suspension parts in the pictures are printed with taulman bridge.
thingiverse
free
Wall mount OpenRC F1 horizontal
...wall mount openrc f1 horizontal
thingiverse
this is a wall mount for the openrc f1 car in a horizontal position.
thingiverse
free
OpenRC Wheel Nut Wrench by barspin
...openrc wheel nut wrench by barspin
thingiverse
wheel nut wrench for the 1:10 openrc project cars.
thingiverse
free
OpenRC Tractor Trailer by Merikisseli
...openrc tractor trailer by merikisseli
thingiverse
...
thingiverse
free
OpenRC Logo by SSwede
... logo, i haven't made the logo, just the 3d model and i'm uploading it by request.
feel free to use it anyway you like :)
thingiverse
free
Bumper/Skidplate for the OpenRC Truggy by Steamerzone
...nted the plate in abs and the damper in taulman bridge. it uses existing holes/mounting points of the openrc truggy for mounting.
F1
3d_export
free
f1
...f1
3dexport
model 3d f1
3d_export
$5
mercedes f1
...mercedes f1
3dexport
racing car mercedes f1
3ddd
$1
McLaren F1
...mclaren f1
3ddd
mclaren f1 без текстур.
3d_ocean
$25
RC F1
...rc f1
3docean
auto car control f1 formula race rc remote speed
remote control f1 car
3d_export
$7
f1 toy
...f1 toy
3dexport
this is a f1 car toy representative of mexcan artists.
3d_export
$15
f1 car mercedes
...f1 car mercedes
3dexport
f1 racing f1 car mercedes
3d_ocean
$19
F1 Tractor
...f1 tractor
3docean
f1 futuristic race tractor red tractor
simple futuristic race tractor model.
3d_ocean
$30
Formula F1
...ic f1 formula indianapolis indy luxury muscle race racer sedan sports street transport tuner vehicle
generic formula f1 race car.
3d_ocean
$50
McLaren F1
...uxury mc mclaren muscle race sedan sports street transport tuner vehicle
highly detailed exterior and interior of the mclaren f1.
turbosquid
$100
F1 Car
...
turbosquid
royalty free 3d model f1 car for download as obj on turbosquid: 3d models for games, architecture, videos. (1263925)
Steering
3d_export
$5
steering wheel
...steering wheel
3dexport
steering wheel
3d_export
$5
steering wheel
...steering wheel
3dexport
steering wheel
3d_ocean
$2
Car steering wheel
...car steering wheel
3docean
car car wheel steering steering wheel wheel
high poly car steering wheel.
3d_ocean
$15
Steering Wheel
... all the meshes are clean and have elegent wireframe -this is a high poly detailed model ready for close up renders. – correct...
design_connected
$7
Steering Wheel
...steering wheel
designconnected
vitra steering wheel computer generated 3d model. designed by nelson, george.
turbosquid
$15
Steering Mechanism
...oyalty free 3d model steering mechanism for download as sldas on turbosquid: 3d models for games, architecture, videos. (1458880)
turbosquid
$4
Steering Wheel
...d
royalty free 3d model steering wheel for download as blend on turbosquid: 3d models for games, architecture, videos. (1562629)
turbosquid
$4
Steering wheel
...d
royalty free 3d model steering wheel for download as blend on turbosquid: 3d models for games, architecture, videos. (1376488)
turbosquid
$4
Steering Wheel
...d
royalty free 3d model steering wheel for download as blend on turbosquid: 3d models for games, architecture, videos. (1562611)
turbosquid
free
Steering Wheel
...uid
royalty free 3d model steering wheel for download as max on turbosquid: 3d models for games, architecture, videos. (1663117)
Adjustable
3d_ocean
$7
Adjustable Wrench
...adjustable wrench
3docean
adjustable wrench highly detailed wrench
highly detailed adjustable wrench.
3ddd
$1
Adjustable Stool
...adjustable stool
3ddd
табурет
wooden adjustable stool.
3d_ocean
$20
Adjustable Gym Bench
...st adjustable bench black equipement gym gymnastic indoor silver sport workout
3d model of black and silver adjustable gym bench.
3d_ocean
$20
Adjustable Gym Bench
...st adjustable bench black equipement gym gymnastic indoor silver sport workout
3d model of black and silver adjustable gym bench.
3d_ocean
$16
Adjustable Weight Bench
...arbell bench black equipement gym gymnastic indoor sport weight workout
3d model of black adjustable weight bench with a barbell.
turbosquid
$5
Adjustable wrench
...
royalty free 3d model adjustable wrench for download as fbx on turbosquid: 3d models for games, architecture, videos. (1313414)
3d_export
$5
adjustable tension lock
...adjustable tension lock
3dexport
adjustable tension lock
turbosquid
$1
Adjustable Wrench
...free 3d model adjustable wrench for download as obj and blend on turbosquid: 3d models for games, architecture, videos. (1446736)
turbosquid
$1
Adjustable Wrench
...y free 3d model adjustable wrench for download as c4d and fbx on turbosquid: 3d models for games, architecture, videos. (1379022)
3d_export
$5
Adjustable key
...adjustable key
3dexport