Thingiverse
Ender 3 rigid bed (tested and working) by Antipaten
by Thingiverse
Last crawled date: 3 years, 3 months ago
I was tired of having to level the bed almost every time i had made a print and I wanted a sturdier construction, but one that was still adjustable. When I found a bag of rubber cable grommets in my drawer of nice-to-have-stuff, I decided to make my own take on a rigid bed.
This bed construction is not fully rigid. It can be adjusted around 4 mm (that's 20/127 of an inch for you imperial guys, if that makes it easier to visualize) and the height dials are firmly held in place even when you apply some forde to the build plate trying to pry a stubborn print loose. My grommets were about 6 mm thick and I would consider 5 mm a minimum as thinner grommets reduce the travel of adjustement too much.
After installing it I can make dozens of prints without any levelling as long as I don't have any excessive nozzle wear or change nozzle. And it's dirt cheap compared to adding auto levelling.
WARNING! A rigid bed is not as forgiving as the stock springy bed. If the zero of the Z-axis is off and the nozzle makes hard contact with the build surface it may cause damage to the nozzle, heat bed surface, or even the hotend and the X- and Z-axis mountings.
PROCEED AT YOUR OWN RISK!
Material needed:
12 rubber grommets 6mm inner diameter. Costs around $3.50 for 50 on ebay. (https://www.ebay.com/sch/i.html?_from=R40&_nkw=rubber+grommet+6mm)
PLA, ABS, PETG or whatever can handle the temperature of the heatbed. I use PLA when printing PLA at 60 degrees and it works fine. If you run your hotter when printing other materials and the PLA parts gets too soft, just print new parts in that material instead and you should be fine again.
Printing:
If you just want a full set of pieces, print the CE3PRO_E3v2_rigid_bed.stl.
If you dropped a piece and it rolled in behind the bookshelf, there are separate STL files for each one.
I printed it with 0.12 mm layer height with a standard 0.4 mm nozzle as this improves the precision and creates a more compact structure less prone to plastic deformation.
I've included the FreeCAD file if you need to adjust anything depending on the grommets you bought.
Assembly:
Remove adjustment wheels and lift the heat bed.
Replace the springs with the following parts from top to bottom; A thin washer, two rubber grommets and a thick washer except in the corner where the cable to the bed heater is fastened. In that corner you use another thin washer instead of a thick one.
Set the bed down on the carriage.
Put each of the four distance tubes in grommets. The tube is there to limit the compression of the grommet, both to make it more rigid and to limit how hard it becomes to turn the wheel.
add the grommets with the inserted distance tube on the bolts between the carriage and the adjustment wheel.
THE FOLLOWING STEPS ARE VERY IMPORTANT!
Always repeat these steps whenever installing a new nozzle as there is almost no give if the nozzle hits the build plate when the printer zeroes in automatically and this may damage the nozzle, hot end or glass bed if it happens.
Tighten it all to lower the bed around 3-4 mm (around 1/8") in all four corners. Do not over tighten as this may damage the grommets and the washers.
Lower the hotend until the nozzle is positioned about 1-2 mm above the bed turning the Z-axle by hand.
Move the Z-axis end stop up until the micro switch clicks.
The printer should now be safe to auto home and do a proper bed levelling.
Adjusting the wheels will feel sticky due to the rubber grommet, but that's intentional to keep the setting from changing unintentionally. To achieve the best results, use a good glass bed and level it to an absolute zero level by setting the z-axis to 0.1 mm, preferrably and use a 0.1 mm feeler gauge. If you use a piece of printer paper, adjust it so it just touches the paper and the paper can be easily reinserted again without moving the nozzle. Go around the corners of the bed another pass and check each corner again until they don't need any more adjustment.
Don't touch the wheel while measuring the bed clearance as even holding your finger on it may alter it a couple of hundreds of a millimeter and throw your measument off.
The nozzle should now barely touch the build plate when the printer zeroes the Z-axis and you should be able to get a perfect first layer on your prints.
This bed construction is not fully rigid. It can be adjusted around 4 mm (that's 20/127 of an inch for you imperial guys, if that makes it easier to visualize) and the height dials are firmly held in place even when you apply some forde to the build plate trying to pry a stubborn print loose. My grommets were about 6 mm thick and I would consider 5 mm a minimum as thinner grommets reduce the travel of adjustement too much.
After installing it I can make dozens of prints without any levelling as long as I don't have any excessive nozzle wear or change nozzle. And it's dirt cheap compared to adding auto levelling.
WARNING! A rigid bed is not as forgiving as the stock springy bed. If the zero of the Z-axis is off and the nozzle makes hard contact with the build surface it may cause damage to the nozzle, heat bed surface, or even the hotend and the X- and Z-axis mountings.
PROCEED AT YOUR OWN RISK!
Material needed:
12 rubber grommets 6mm inner diameter. Costs around $3.50 for 50 on ebay. (https://www.ebay.com/sch/i.html?_from=R40&_nkw=rubber+grommet+6mm)
PLA, ABS, PETG or whatever can handle the temperature of the heatbed. I use PLA when printing PLA at 60 degrees and it works fine. If you run your hotter when printing other materials and the PLA parts gets too soft, just print new parts in that material instead and you should be fine again.
Printing:
If you just want a full set of pieces, print the CE3PRO_E3v2_rigid_bed.stl.
If you dropped a piece and it rolled in behind the bookshelf, there are separate STL files for each one.
I printed it with 0.12 mm layer height with a standard 0.4 mm nozzle as this improves the precision and creates a more compact structure less prone to plastic deformation.
I've included the FreeCAD file if you need to adjust anything depending on the grommets you bought.
Assembly:
Remove adjustment wheels and lift the heat bed.
Replace the springs with the following parts from top to bottom; A thin washer, two rubber grommets and a thick washer except in the corner where the cable to the bed heater is fastened. In that corner you use another thin washer instead of a thick one.
Set the bed down on the carriage.
Put each of the four distance tubes in grommets. The tube is there to limit the compression of the grommet, both to make it more rigid and to limit how hard it becomes to turn the wheel.
add the grommets with the inserted distance tube on the bolts between the carriage and the adjustment wheel.
THE FOLLOWING STEPS ARE VERY IMPORTANT!
Always repeat these steps whenever installing a new nozzle as there is almost no give if the nozzle hits the build plate when the printer zeroes in automatically and this may damage the nozzle, hot end or glass bed if it happens.
Tighten it all to lower the bed around 3-4 mm (around 1/8") in all four corners. Do not over tighten as this may damage the grommets and the washers.
Lower the hotend until the nozzle is positioned about 1-2 mm above the bed turning the Z-axle by hand.
Move the Z-axis end stop up until the micro switch clicks.
The printer should now be safe to auto home and do a proper bed levelling.
Adjusting the wheels will feel sticky due to the rubber grommet, but that's intentional to keep the setting from changing unintentionally. To achieve the best results, use a good glass bed and level it to an absolute zero level by setting the z-axis to 0.1 mm, preferrably and use a 0.1 mm feeler gauge. If you use a piece of printer paper, adjust it so it just touches the paper and the paper can be easily reinserted again without moving the nozzle. Go around the corners of the bed another pass and check each corner again until they don't need any more adjustment.
Don't touch the wheel while measuring the bed clearance as even holding your finger on it may alter it a couple of hundreds of a millimeter and throw your measument off.
The nozzle should now barely touch the build plate when the printer zeroes the Z-axis and you should be able to get a perfect first layer on your prints.
Similar models
thingiverse
free
Indicator holder for bed leveling and offset by thomasgerster97
...should be leveled and your z-offset should be point on.
note: if your z-offset is off it might be your steps per mm in the z-axis
thingiverse
free
Bed Leveling Grid v2
...rm your bed is fully leveled. make note of any problems spots that might indicate bed warping that you should avoid printing on.
thingiverse
free
Semi-auto bed calibration for 300*300 bed size by Ongelofeloos
...orner press the button again and it will go to the next corner. continue doing this until your printer bed is levelled correctly.
thingiverse
free
Prusa i3 Dial Indicator Mount by henryarnold
...d and do you normal z height adjustment. all four corners are level so no check should be needed other than the middle of the bed
thingiverse
free
Tread Depth Gauge Holder for Sapphire Pro/Plus and Creality by wjohnsaunders
...hat adjustment is gradually removed over successive layers, so any leveling error will be reflected in the geometry of your part.
thingiverse
free
Mechanical Dial Gauge Bracket by TurbulantCalm
...channel:
turbulantcalm's adventures in 3d printing.
i love the way the adaptor looks a little like a zombie bart simpson...
thingiverse
free
Ender 3 Pro Bed Leveling Dial Indicator Mount - Caliper
...e ii, the bolt used is a 1/4-20 1" length.
it is a really easy print: no supports-60mm/s- .2mm layer height
happy printing!
thingiverse
free
HyperCube Dial Indicator Mount by henryarnold
...dial indicator i used although you can buy a similar unit from harbor freight.https://www.amazon.com and then search for "b01g9k8u5g"...
thingiverse
free
Anet A8 $4 Bed Leveling Accessory by VegasGuy
...bed. the coupler must be printed in tpu or similar flexible material in order to achieve the correct amount...
thingiverse
free
Bed leveling and adhesion test by Saur0n
...er)
finally, you can tune first layer height and first layer extrusion in slicing program - so it will stick properly to surface.
Rigid
turbosquid
$15
Rigid Bag Filter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Rigid body Cube
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$12
Semi Rigid Rubberduck 3D Model
... tender yacht marine boat rigid bottom inflatable dinghy run-around 38m
semi rigid rubberduck 3d model southdesign 32727 3dexport
turbosquid
$35
Among Us Rigid Character
...among us rigid character for download as blend, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1637362)
3d_export
$15
Rigid Bag Filter 3D Model
...rigid bag filter 3d model
3dexport
filter bag clean air ahu conditioning
rigid bag filter 3d model matvic 85845 3dexport
3d_export
$60
Rabbit Rigid 3D Model
...oe hare burrow long ears pet 3d realistic rigged white brown fur small cute mammal
rabbit rigid 3d model scorpio47 78247 3dexport
cg_studio
$119
Mercedes Antos rigid truck3d model
... .fbx .lwo .max .obj .xsi - mercedes antos rigid truck 3d model, royalty free license available, instant download after purchase.
3d_export
$119
Mercedes Antos rigid truck 3D Model
...os actros van boxtruck trailer heavy daimler german european rigid
mercedes antos rigid truck 3d model fisherman3d 66670 3dexport
3d_export
$50
of a hydrofoil board with a rigid wing sail
...model is made in the form of: hull parts, sail parts, as well as a ballast centerboard and keel.<br>all peace and goodness.
turbosquid
$12
Device for loading and unloading of non-rigid CME roller tracks
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Ender
3ddd
$1
Enders / Elegance
...enders / elegance
3ddd
обогреватель
уличный газовый обогреватель enders elegance
высота: 2200 мм
3d_export
free
ender 3 frame cavity covers
... of the creality ender 3 - makes it look a bit more attractive it just slides into the open channels of the aluminium framework
turbosquid
$1
pen support for ender 3
...y free 3d model pen support for ender 3 for download as blend on turbosquid: 3d models for games, architecture, videos. (1611282)
3d_ocean
$9
Ender Dragon Minecraft
...ojang obj poly videogames
ender dragon minecraft created with cinema 4d r15 formats included: max 2013 – fbx 2012 – c4d r15 – obj
3d_export
free
Creality ender enclosure webcam mount
...e creality enclosure. sure is better than a tripod. change it up if it helps. i printed pla with 50% infill on my dd ender 3 pro.
3d_export
free
ender 3 enclosure corners
...er corners and 4 upper corners, using 25mmx25mm angled aluminium pieces that gets covered on inside of the frame with plexiglass
3d_export
free
ender 3 3d print bed clips
...ed + normal aluminium bed frame of the creality ender 3 = 6mm (b) these clips are designed for glass plate + aluminium bed = 4mm
3d_export
$5
GRUMPY CAT
...grumpy cat 3dexport grumpy cat to print in ender ...
3d_export
$5
Logs fire
...with one multi material for corona and vray r ender. albedo, normal, uvmap, roughness format jpg 4096x4096 models:...
3d_export
$42
excavator
...is the original size. 0.12 mm printing surface creality ender5 ...
Bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
Bed
...bed
3ddd
bed , постельное белье , постель
bed
3d_export
$7
bed adairs bed
...rs bed
3dexport
bed adairs bed in modern style. if you want a smoother surface, please turn on turbosmooth in the modifier list.
Tested
turbosquid
$99
test
...st
turbosquid
royalty free 3d model test for download as max on turbosquid: 3d models for games, architecture, videos. (1251637)
turbosquid
$63
TEST
...st
turbosquid
royalty free 3d model test for download as max on turbosquid: 3d models for games, architecture, videos. (1446233)
turbosquid
$1
test
...st
turbosquid
royalty free 3d model test for download as fbx on turbosquid: 3d models for games, architecture, videos. (1360941)
3d_export
free
johnny test
...johnny test
3dexport
johnny test 3d
turbosquid
$15
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
gripper test
...gripper test
3dexport
robot gripper test model
Working
3d_export
$5
WORKING PLATFORM
...working platform
3dexport
working platform 4000x3000x1500mm
design_connected
$16
Working set
...working set
designconnected
smallaccents working set computer generated 3d model.
3ddd
free
Pinao / Stelar Works
...pinao / stelar works
3ddd
stelar works , stellar works
стулья pinao от stelar works
design_connected
$13
Work Lamp
...work lamp
designconnected
design house stockholm work lamp computer generated 3d model. designed by form us with love.
turbosquid
$6
Road Works
...turbosquid
royalty free 3d model road works for download as on turbosquid: 3d models for games, architecture, videos. (1151328)
3ddd
free
Stellar Works Lumar
...llar works , lumar , барный
stellar works lumar
turbosquid
$20
Work boots
...bosquid
royalty free 3d model work boots for download as stl on turbosquid: 3d models for games, architecture, videos. (1313566)
turbosquid
$8
Desk Work
...osquid
royalty free 3d model desk work for download as blend on turbosquid: 3d models for games, architecture, videos. (1381338)
turbosquid
$5
Work Desk
...osquid
royalty free 3d model work desk for download as blend on turbosquid: 3d models for games, architecture, videos. (1435344)
turbosquid
$1
Plant for work
...uid
royalty free 3d model plant for work for download as obj on turbosquid: 3d models for games, architecture, videos. (1557514)
3
turbosquid
$10
Mountain Bike 3 -3 of 3
...model mountain bike 3 (#3 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438752)
turbosquid
$6
Rock 3-3
...urbosquid
royalty free 3d model rock 3-3 for download as obj on turbosquid: 3d models for games, architecture, videos. (1628065)
turbosquid
$29
Books 150 pieces 3-3-3
...books 150 pieces 3-3-3 for download as max, obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1384033)
turbosquid
$3
Genesis 3 Clothing 3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
hinge 3
...hinge 3
3dexport
hinge 3
3ddd
$1
Розетка 3
...розетка 3
3ddd
розетка
розетка 3
turbosquid
$50
is-3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Mountain Bike 3 -2 of 3
...model mountain bike 3 (#2 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438750)
turbosquid
$10
Mountain Bike 1 -3 of 3
...model mountain bike 1 (#3 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438743)
3d_export
$5
3 CATS
...3 cats
3dexport
3 cats pen holder