16 set surfaces mk8 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Mk8 extruder rear heatsink + fan support by andcl
...the heat transfer and cooling features of the whole set ...
thingiverse
free
MK8 Adjustable Fan Holder by artdavis
...of your fan and set the fan_width and fan_holedist setings in the [fan/duct] tab. typically for a 60mm fan:...
thingiverse
free
Parametric Nozzle Storage Box (V6 & MK8) by Theguffy1990
...with two different tolerances. by default, all tolerances are set to 0.3mm. if you'd like a tighter fit, there...
thingiverse
free
Mutant Mounts for Mk8/ Microswiss/ V6 & Volcano hotends by Hangtight
...z axis to allow you to get the z offset identical between all your hotend options. swap from a...
thingiverse
free
Hero Me Mutant HotEnd Cooling System by mediaman
...tip/bed surface. you will need to measure the x/y offset of the abl sensor to the nozzle and either...
thingiverse
free
Modifying an M8 Extruder Stepper for Bowden Use by DougInAZ
...adapt the m8 extruder stepper motor to a bowden setp however, it is not ideal. it took me a...
thingiverse
free
Cooling Fan Shroud for Creality Ender-2 by lewtwo
...unless the bottom cap screw is replaced a proper set screw. this shroud will work with the newer model...
thingiverse
free
D-Bot Fully-Supported Extruder by dotorg
...screw closest to the bowden connector (which has no inset is left out. attach the bearing to the tension...
thingiverse
free
Reprap - Funbot i1 by RepRapOsterlen
...can control the fan in slic3r with the fan setings this way so not bad at all actually :)...
thingiverse
free
C3DP v0 a 34€/40$ Printer [28BYJ-48 5V] by milan2sky
...bill of materials how to build trouble shooting print setings how i design this questions & answers the design...
thingiverse
free
Replicator 2 Extruder Upgrade by whpthomas
...these inherent problems, fulfils this usability objective. so i set about to design an upgrade that used parts which...
thingiverse
free
4:1 Planetary Extruder
...if the extruder is mated directly to the planetary gearset use the spacer between to prevent extruder pins falling...
thingiverse
free
Bowden dual/quad extrusion extruder (single-nozzle single-drive) + video by FDMTech
...color: see video in gallery above! cura and firmware setings released at my github repo if you have a...
thingiverse
free
Creality CR-10S Upgrades by macd2point0
...upgrade http://a.co/0yuos0o supporting rod set for creality 3d cr-10 https://www.ebay.com/itm/supporting-rod-setfor-creality-3d-cr-10-cr-10s-3d-printer-diy-upgrade-supply-/222980833024?_trksid=p2349526.m4383.l10137.c10&nordt=true&rt=nc&orig_cvip=true ...
thingiverse
free
Scalar Family - 3D Printer by 3DModularSystems
...for providing this great firmware and evolutions. misc calibration set http://www.thingiverse.com/thing:909829 scalar xl - printing at 60mm/s with e3d...
thingiverse
free
DemonDeltaMicro - Simplest reprap delta frame to date. by DjDemonD
...mm. use this for the next print as your z-offset you don't have to do this every time (but...