18 room direction 04 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Creality Cr-10 Flexion hotend direct mount by T_kovax88
...some bowden connector clips/locks to ensure there is no room for the bowden tube to lift upon retraction. some...
thingiverse
free
Cisco Webex Room Kit Series Stands by jarda_kp
...kg and the legs should be stiff in front-back direction to avoid vibrations. room kit recommended print position is...
thingiverse
free
Y-axis rework for Anet A8 by matsekberg
...a little bit to the left to make more room for the belt and belt mount. also made the...
thingiverse
free
CONCEPTUAL DESIGN OF A HYBRID ELECTRIC BLIMP WITH COMPRESSED AIR SYSTEM by Isarts3d
...empty the load module, the air would have to room temperature, and when the load module, the pocket would...
thingiverse
free
Mattel The Child 11-inch Plush hollow Skeleton and Flat feet by rkxone
...a few hours off the print and allows more room to put in electronics and speakers etc. i left...
thingiverse
free
J-Struder : 1.75mm Bowden Extruder For NEMA 17 Motor by junaling
...the base (retraction stabilizer and reinforcement) and guides (more room for gear, plunger, rounded edges) this design is inspired...
thingiverse
free
HobbyKing BSR BZ-222 gearbox by Schiksie
...not printed that one yet so not sure the room i cut away is now enough. the motorplate is...
thingiverse
free
Auto-winding drum for weight-driven clock
...14 or larger in the future (should be enough room. components used: arduino nano 5v 28byj-48 stepper motor and...
thingiverse
free
Ultralight Endfed Triband Half-Wave Antenna by mfhepp
...the 80m coil in the files. this one has room for the coil in the middle of the winder....
thingiverse
free
Loches Z Axis Upgrade for MakerGear Prusa Mendel by Lochemage
...is in a hole that does not give it room to 'wiggle', this gives it the stability it needs...
thingiverse
free
LoPro 164 Mini Quad for up to 3.75" props by andimon
...push back the xt30 plug for a little more room (note revised v2 mid plate). this design is for...
thingiverse
free
The Monolith 50mm E3D V6 Shroud Fanduct by PokeyDoggo
...should fit on any groovemount if there is enough room at the front. i kept about 1mm of space...
thingiverse
free
Fully 3D printed sailplane model. optimized for 0.2 nozzle (weight reduction) by grafalex
...elevator until it balked to the rudder. no more room to trim. fortunately it helped. finally i added more...
thingiverse
free
Open Aikido Vehicle Elements Introduction by usertogo
...brushed onto scrolls which are hung in the tea room in the context of tea ceremony, ichi-go ichi-e reminds...
thingiverse
free
ROB-O Junior FFF 3D Printer using 80/20s 10/10 (1"x1") extrusion by Thump2010
...will post it as a separate thing, i left room for z probes etc. in the stl model is...
thingiverse
free
DemonDeltaMicro - Simplest reprap delta frame to date. by DjDemonD
...type in configuration.h. make sure it reads close to room temp at room temp. then try 40 degc, 60...
grabcad
free
Technical room of single-family house.
...ource of energy.
air conditioning is provided by a heat pump. house is equipped with air handling unit with rotor heat exchanger.
3dwarehouse
free
Fort Miles Coast Artillery Fire Control Tower 04
...by the fct crews. this would allow the plotting room to track and triangulate a target's course and to...