thingiverse

free

Dropper Post Lever by Warrengrice

...ver for cable operated dropper posts. fits 22mm handle bars. requires a 688zz bearing and a couple of m3 caphead screws and nuts.

thingiverse

free

Dolmar MG5300.4 Throttle lever by moonspy

...ave to print it! pla worked just fine but of course petg would be better. just now tested it for couple of hours and no problems.

thingiverse

free

Lever for Harbor Freight bar clamp by Sparky6548

...en lever. i have put more pressure on this one than it took to break the original ones, so hopefully i now have two good clamps.

thingiverse

free

Acerbis petcock lever by PavelNS

...ently remove dummy crossbar after print. and yeah, if you like my work and ideas, feel free to support me with a couple of bucks.

thingiverse

free

Anycubic Mega S Extruder lever (two versions) by IJK_CZ

...r filament slippery. in case you have not the original lever, or a version wiothout inset, you should use the standalone version.

thingiverse

free

Cyma CM.030 Trigger Lever by Loswave

...when being carefully removed... fortunately we live in a day and age where we can make our own parts. the best part is, it works!

thingiverse

free

Primary Arms 4-14x FFP Scope (1st gen) Throw Lever by PoniesWhee

...luminated versions. note - as a couple of people have note below this works on the first gen 4-14x which has a smaller zoom ring.

thingiverse

free

Primary Arms 1-6 acss sfp throw lever by hulabaloo

...atte black. the tpu was 20-30% no supports with the wide part down. i use the 101% version. it leaves almost no gap at the screw.

thingiverse

free

vampire skull media shift knob

...ft lever you have. printed on a voxel .18 layer 30%solid 4 shells matter hackers abs then acetone vapor bath for a couple hours.

thingiverse

free

Minute Engine by brlaw

...unction, see link below for full instructions. https://brianlawswoodenclocks.blogspot.com/2020/09/a-design-for-minute-engine.html

thingiverse

free

M4 Magazine Adapter For M56 Airsoft Shotgun by enone

...falling out. if the mag release lever is too lose to goes too far in the mag well then a bigger pin 2.7-2.9 mm might be required.

thingiverse

free

Nerf Modulus Lever by nerf3d

...with the community to gather inputs. feel free to print, edit etc but just don't forget to provide me your feedback. thanks.

thingiverse

free

HICTOP Prusa i3 Extruder Mount / Lever (adjustable) by Sefrez

...is shifts the spring compression length range up 1.5mm allowing for less tension if my original mount is creating still too much.

thingiverse

free

Faucet Lever for Absolu water dispenser (like part B-2030) by nik_qc

...have made a simple model that works well and replaces this original part. the original part is called b-2030 absolu faucet lever.

thingiverse

free

Pentax 6x7 K mount adaptor by simonpw

...l distance is correct for infinity focus. i don't have a lens which uses the external mount, so i can't test that so far.

thingiverse

free

flexible filament extruder by techwit

...all you need to do is print the v4 body and clamp, and the lever. the clamp holds the bowden coupling in place using m3 screw/nut

thingiverse

free

E3D Titan Extruder CLONE- All parts by sale723

...dapter -pneumatic coupling -tightening screw -filament gear -bottom cover -filament guide -lever -stepper motor holder -top cover

thingiverse

free

Compact Bowden Extruder Derivative by MacAttak

...f the output channel to help with threading filament through, and various other minor alterations. updated: v2 of design posted

thingiverse

free

Servo Operated Knuckle Coupling by dagnall53

...b housings. these are here: https://www.thingiverse.com/thing:1989545 chose the housing that works best for your truck/coach etc.

thingiverse

free

throttle panel for flightsim by g0per

...as tolerances are quite tight. screws are m2 for microswitches and m3 for all remaining parts unless specified (various lengths).

thingiverse

free

Replacement Coupler for Playmobil Trains by af12689

...pport. the third photo is a comparison between the printed part and the original playmobil coupler (which has a worn out spring).

thingiverse

free

Throttle Quadrant Quick Release Lever Handles by IAintDead

...r whatever knob sits on top. my big black handle will wobble too much at less than .84 mm, but all the others are fine at .6 mm.

thingiverse

free

Zero Clearance Extruder Body, No Coupling by ThisIsMyThingiverseAccount

...ars, etc.. i've printed quite a lot with this, and no problems. quite happy with it. i've printed pla, petg, and 91a tpu.

thingiverse

free

Luger P08 Mainspring Assembly by kobing

...an be inserted into the body. for the spring, i stretched a compressed 11/32"x 1-27/32" spring that i bought on amazon.

thingiverse

free

'Flextruder' Malyan M200 Flexible Filament Extruder by JanBe

... the gear (marked yellow in the photo) you´ll need a 2mm (15mm long) rod or similar bolt and 3mm metric bolt + nut for the clamp.

thingiverse

free

RC Shark - Alternate Nose Gear Strut/Suspension by Kingmiwok

...and the slight change in steering as the suspension moved), but it was still much better for me. consider it a work in progress.

thingiverse

free

Car Bike Rack Accessory (Rhode Gear) by geotrick

...oving the curves on the sides and shortening the length. it is being printed now. i will post a couple of photos when i get them.

thingiverse

free

Shimano Bike Hydraulic Disk Brake Caliper Spacer Block by virtualight

...mano calipers. you can usually get them from your local bike shop for a couple of dollars but why not print them for a few cents!

thingiverse

free

Compact Bowden Extruder by Lloyd_Hayes

...my print.) short spring and you may want one or two filament guides the way that mine is setup. filament guides with 4 mm thread.

thingiverse

free

Airsoft VSR10 To M4 Mag Adapter by enone

...sed 0.3mm for the adapter and 0.2mm for the release lever and spring. make sure there is no debris in the feed tube before using.

thingiverse

free

Simple filament extruder puller by james_III

...tweak on lever holes, for easier function. update 28.10.2015 alternative version for base, now with nema 17 and 23 bolt patterns.

thingiverse

free

Rostock Max Extruder - DEPRECATED by kitecraft

...ring from the lever arm) results: i've successfully completed a 3 hour print with tpe 80a and the results are most excellent.

thingiverse

free

Throttle Quadrant by AdamF3A

...s five levers, fourteen switches and seven rotary encoders with push buttons (one of which is designed to be used as a trim wheel

thingiverse

free

Bowden extruder by Axbri

...iding flexible filaments. i made this using sketchup, and i have included the skp-file as well. feel free to modify if you want.

thingiverse

free

Flexistruder remix for HICtop by KVerb

...lu frame, but apparently i didn't make the effort to save it.. if enough requests arise i will redesign it and put it online.

thingiverse

free

Magnetic PCB Holder by sneakypoo

...me reason...) is simply used to more easily dislodge the thing after you stick it down. neodymium magnets are pretty darn strong.

thingiverse

free

Basic Trailer Project: Coupling parts by rcmodeler

...needs 2 springs) i have a couple of spring assortments and with a little cutting and bending i usually get something that works.

thingiverse

free

Simple expandable 4 axis CNC (6 printed parts) by siderits

...-standard-sae-regular-nuts/4293807 limit switch there are dozens of different kinds of whisker, lever arm etc. here is one kind.

thingiverse

free

Auto bed-leveling servo mount by stephenrc

...p servo mount thicker (4mm). added countersinks to the mounting holes for the servo, the mounting screw would obstruct the lever.

thingiverse

free

Motorcyle Throttle Lock by dmai

...olt (20mm) and a standard nut. use stainless of course. if you decide to try one of these, please take pic and share it?? thanks!

thingiverse

free

OneUp/TwoUp Extruder Housing Assembly by markqv

...printer. here are the pieces: modified housing filament lever 2 piece carriage slip-on belt clamp main fan bracket motor spacer

thingiverse

free

3D PRINTER TOOL by cpertchik

...at you can print a couple from the last dregs of a filament reel in an awful color that you know you'll never ever buy again.

thingiverse

free

Dial Thickness Caliper Brackets by ShinyObjects

...t the full 0.31" of travel. you may be able to adjust the height of the cap nut by changing the number of washers under it.

sketchfab

$10

Volcanic Revolver

...nings rifle, patenting the smith-jennings in 1851 - volcanic revolver - buy royalty free 3d model by nicola ristagno (@nickframe)

thingiverse

free

Atem Mini Pro Iso Fade to Black FTB Button Cover by nikasio14

...e hinge is printed with 0,1 mm tolerance but should be okay for most printers and will stay open on the board at almost any angle

thingiverse

free

WRX Shift Knob by zachstence

...o lettering are a friction fit. there is a 0.2mm tolerance. let me know if you have any issues printing or need adjustments made!

thingiverse

free

MK8 Bowden Extruder 1,75mm for 2020 Extrusion with Filament Sensor by laubed

...m4x20 ant over to the m4x10 attach the microswitch to the extruder3/extruder2 assembly for filament detection with 2 m2x10 screws

thingiverse

free

Saturn SL2 Parking Brake Button by ThomasPaine

...process. i would have divided the part up into 2 or 3 subsections. it would have been much easier to make slight modifications.

thingiverse

free

PCB Holder Remix by jabixby

...youtube video of one of these working, built by 3dsage https://www.thingiverse.com/3dsage/about : : https://youtu.be/c9ysowoa3fm

thingiverse

free

Jumper T-lite Balanced Neck Strap Holder by IJK_CZ

...g the four screws into back radio panel. print both parts in designed position. support for lever is possible, but not necessary.

thingiverse

free

F-mount/C-mount lens coupler / telescope / beam expander

...aperture ring. the attached photographs show the coupler with a 12mm edmund otpics lens attached to a 50mm nikon af-s 1.8g lens.

thingiverse

free

NEW Bowden Extruder Gimbal by PBeis

...u crank up the speed on your printer. https://www.amazon.ca/gp/product/b00edk5gie/ref=oh_aui_detailpage_o06_s00?ie=utf8&psc=1

thingiverse

free

Extruder Assembly for Hobb Goblin / MK8-style + Groove Mount Bowden Adapter; Ender 2 / CR-10 by nanowhisker

...e it. the gear i use has a diameter of 7 mm at the filament level. i set e144 for the stepper to account for the lower diameter.

thingiverse

free

Bike Steerer Tube Storage Plug by Drazen

... used two nuts but there are a few ways you could do this. print the wing nut if you want to make it 'tool-less' to open.

thingiverse

free

A couple of changes to Crossbow by Alzibiff

...h are also uploaded separately. thank you tech2c, hope you don't mind me making the above changes to a very elegant design.

thingiverse

free

Console Clip for Trash Bag - 2020 Hyundai Santa Fe

...ple of the photos show kinda "squashed" above, but you can take a look at the .stl file and see the actual proportions.

thingiverse

free

Flying Tourbillon Model V (Daniels Double Independant Wheel Remontoir Escapement) by A26

...mechanical complexity. even so, i find its visual symmetry coupled with its intentionally asymmetric tick more appealing. the latter...

thingiverse

free

Tom's Extruder by Tom143

...without any support material where the idler bearing sits. your results may vary depending on the print quality of your printer.

thingiverse

free

Air Arms EV2 Regulator Removal Tool by HashBrown123

...r block into a work bench and twisted the block with the wood levers i made. it's very simple when you have the right tools.

thingiverse

free

Faster Glock 9mm Double Stack Speed Loader by gt_fourza

...x0hn1toqmzdknajmzxp8hvgtem and no, this does not work with your 40s&w magazines, you're better off loading those by hand.

thingiverse

free

Spring Drive Block Extruder for CTC Bizer (Replicator Clone) MK8 Remix for Makerbot Clone 3D Printers (FlashForge, Wanhao) by jerryjs8

...and stp if you see the need to modify it. you can also simply download ctc_drive_block_complete_lr.thing to just get to printing!

thingiverse

free

Ultifeeder the ultimate extruder feeder for your Ultimaker 2 by roumen

... ball bearing (12mm long) the original um2 extruder spring a small piece of bowden tube to fit in the lower opening of the base.

thingiverse

free

Reworked_Geeetech_Printer_Carriage by Lloyd_Hayes

...lt path has also been opened for easier belt travel. all i can say here is that it's not pretty, but it works on my printer.

thingiverse

free

Countertop Tea Chest by Festus440

... held in place with a short length of 1.75mm printer filament. i'll add photos of a printed version when it's complete.

thingiverse

free

Direct drive extruder for FLSUN Cube by tato_713

...king these models, letting them available and free for everyone. if you want to support my work, you can contribute with me here:

thingiverse

free

Husqvarna Viking, 6000 series Follower Cam Replacement, Sewing Machine Parts by PSomeone

...nothing hits and everything is assembled properly before adding power. add power slowly, don't go gun hoe right off the bat.

thingiverse

free

Functional Attack on Titan Sword V2 (read description before printing!) by Davidsson

...ade_top.stl' and 'blade_mid.stl' all files downloaded before this update will be incompatible with the current model.

thingiverse

free

Allen Key ABL Probe Remix by Scrubulum

...r the metal lever but it isn't hard. suppose the rest could be lowered a little to improve this but i like it the way it is.

thingiverse

free

Soldering Aid / Helping Hands by AirwavesTed

...sy opening of the jaws. i'm currently looking to use small compression springs to close the jaws instead of the rubber bands.

thingiverse

free

Hypercube Extruder Mount on 2020 Profiles by datdiy

...the gear counter part edit 2018-05-14: i've made another version with a longer body https://www.thingiverse.com/thing:2910497

thingiverse

free

Cateye Micro Wireless Bike Computer Stem & Headset Mounts by mentalbob

...at a 45 degree angle with 5-10% support (as columns) and an overhang angle of 80+ degrees and a brim to minimize support cleanup.

thingiverse

free

AEG Favorit dishwasher water circulation pump wheel by juha_j

...f not, do not over tighten, but shorten shaft on wheel. run couple sets of dishes side cover open to see if there is some leaks.

thingiverse

free

Garden Hose Manifold Mounting Bracket by markabyrd

...e to have success printing abs in the dry winter months. the 4-way hose manifold i used... https://www.amazon.com/s?k=b08g5887kk

thingiverse

free

KLR650 Clutch Switch by Tinyhead

...like with them. the normally-open contact is required for the switch, causing the contact to close when the clutch is pulled in.

thingiverse

free

TurboGrafx-16 Turbo Everdrive Shell by DogP

...w abs filament, but looks kinda green). i also added a small hole for the led to shine through, and a couple other minor tweaks.

thingiverse

free

The All You Can Feed Buffet v1.3 :-) by mnis

...riptions are highly desirable. so if you use my designs and parts thereof, please take a few moments to convey a little feedback.

thingiverse

free

Daniels Double Remontoir Tourbillon Escapement by A26

...mechanical complexity. even so, i find its visual symmetry coupled with its intentionally asymmetric tick more appealing. the latter...

thingiverse

free

Audi TT MK1 Dome / Map Light Fix

...and apply some epoxy to glue in place. clamp with clothes pins. enjoy the fact that a few minutes worth of time saved you $180.

thingiverse

free

filament sensor switchbox remix (for maplin roller microswitch) by buxton

...y pause at run-out. the original snapped together really nicely and i think i've managed to not ruin that part of the design.

thingiverse

free

KIS extruder - direct drive Nema 17 & Mk8 for 1.75 filament by Phil_Maddox

...ction on filament update 5th apr 2015 > added a couple of simple bracket options which both require longer screws ( m3 x 25)

thingiverse

free

HP 27f monitor VESA adapter by ClintonRH

...personal desk. but it is not appropriate to use this part in any circumstance where failure might endanger some one's safety.

thingiverse

free

G3DK Projekt by GaryK47

...ect, this is remix. unfortunately i can't find the link to it anymore. ex = extruder parts mo = motor parts z = z-axis parts

thingiverse

free

CZ Scorpion AK Style Safety by Semper1371

...ecause this is how the ak selector is meant to function since the ak does not have a bolt release (let alone a left side safety).

thingiverse

free

Irwin Quick Grip Track Adapter by supergimp

...ly given their size. although these track saws can often be used without clamps at all, so the micro model is probably just fine.

thingiverse

free

Geeetech Prusa I3 Pro End Stop Spacers by DougInAZ

...n the printer controller software (repetier in my case) or by a subtractive machining method (with a file, sandpaper or grinder).

thingiverse

free

Seat Release Knob 2005-2014 Ford Mustang by timeshell

...80458&li=shops https://www.shapeways.com/product/xhs5chaaw/2014-ford-mustang-seat-release-knob?optionid=72074822&li=shops

thingiverse

free

PetSafe Healthy Pet Simply Feed conveyor belt trimming jig by ge0ff

...idn't take any pictures before i filled the whole hopper with food. i'll try to take some next time it's convenient.

thingiverse

free

Clothesline Reel by rickswirebox

...d useful and yours prints well. happy 3d printing!! oh! as well, please post a picture of your make. will love to see one made !!

thingiverse

free

Mag Release Mod for Rival Caliburn U - Simplified

...ify what is different from the original: rogmagback_modv2.stl replaces rogmagback.stl rogmagrelease_modv1.stl replaces rogmr2.stl

thingiverse

free

Geeetech MK8 extruder fan duct by valand70

...ss filament extruding machine - ebay -filament extruding machine - aliexpress pellets for extruding machine aliexpress coupon

thingiverse

free

Pitan (as in printed Titan :-) Geared Extruder by MakinBug

...his drakon extruder https://www.thingiverse.com/thing:2172854 https://youtu.be/mrs9yidganohttps://youtu.be/2xwi5pundr8 enjoy :-)

thingiverse

free

Ender Pro 3 filament runout sensor by mpd352

...de the bearing, making the octoprint incorrectly think there was no filament. so, i added a filament hole/guide to prevent that.

thingiverse

free

HackerBox Biosense Case by JohnFen

...nk of a couple of reasons why it may not. buyer beware! (printed with makergeek's paul's blue car pla and push black pla)

thingiverse

free

Pitbull XL Extruder by rejaak

...tepper motor (4) m3x35mm bolts (2) m3x8mm bolts (1) 688zz bearing (without flange) (1) mk7 hobbed gear with 8mm bore (~12mm dia.)

thingiverse

free

Ender 5 Mini Tool Changer by stuartofmt

...duct to help stabilize. i also created the step file so that the length of the duct can be lengthened or (more likely) shortened.

thingiverse

free

Lights for $33 Time Lapse Camera by Webweave

...ebay.com/itm/5pcs-3w-white-cob-high-power-led-stripe-led-light-emitting-diode/352236956976?hash=item5202f56d30:g:x4uaaoswetjaogxq

thingiverse

free

BreakShot (SledgeFire Add-on) by N8thin

...legde fire, sladge fire, sladgefire, slegdh fire, slegdhfire and for some other tags, shotgun, shell, zombie strike, and blaster.

thingiverse

free

MPSM Fully Adjustable Z Spacer (MP Select Mini) by wileykyoto

...t some point (around 0.7mm on my printer) the limit switch will slip off the end of the spacer and effectively act as 0mm offset.

thingiverse

free

Laser cut Quad Copter frame by roadhog

...the color of the cut line, this will allow you to engrave cut and score at the same time. hope this helps have a nice day jim

thingiverse

free

Sim Racing Hand Brake by SlapFish

...y bardocz: https://www.thingiverse.com/thing:4078775 good luck, and happy racing/parachuting/blasting/evil/cookies/gross veggies!

thingiverse

free

Aprilia SR50 Brake Switch Boot by xcmtbjason

...dated 2015, so i would assume it is the "new" part, no date on the other package and it looked like an older package...

thingiverse

free

Modular mountable SD/MicroSD Card box with extract button and auto-close cover by magonegro

...l hole, real world cards now fits perfect. increased ejection distance to allow an easier removal of the card. job done! (by now)

thingiverse

free

FP-68S Twig Snake Extra Compact FTW flywheel pistol foam blaster

...nels with motor screws. make sure they don't grind on the magazine, otherwise you will need to trim them a little. 12) enjoy!

thingiverse

free

Geeetech A20M Chimear Clone (Semi) Direct Drive Mount by Abi_Jen

...inactive nozzle clear to avoid parts strikes and ozzing, coupled with a single stepper, dual extruder setup. as it...

thingiverse

free

Geeetech A20M Chimera Clone (almost) Direct Drive Mount by Abi_Jen

...inactive nozzle clear to avoid parts strikes and ozzing, coupled with a single stepper, dual extruder setup. as it...

thingiverse

free

FP-68D Night Snake Compact dual cage FTW flywheel pistol foam blaster

...nels with motor screws. make sure they don't grind on the magazine, otherwise you will need to trim them a little. 11) enjoy!

thingiverse

free

Laser Module for Maker Select V2 by lgv2016

...the laser turns on briefly while the controller is on. either add a switch or disconnect the laser until you are ready to use it.

thingiverse

free

Formula B1 - (Sim racing) steering wheel

...len) keys pair of scissors jig saw with aluminium blade drill 3, 4, 5, 12 mm file or rotary tool with mill utility knife wrenches

thingiverse

free

Core-T Printed Wheels All Axis Spectra Driven by runninfarmer

...www.thingiverse.com/thing:31216 current frame volume is 350mm x 350 mm x 350 mm. build volume is about 175 mm x 250 mm x 330 mm.

thingiverse

free

FP-68 Grass Snake Compact FTW flywheel pistol foam blaster

...nels with motor screws. make sure they don't grind on the magazine, otherwise you will need to trim them a little. 11) enjoy!

thingiverse

free

Shower Head to Garden Hose Adaptor NPT 1/2 female to 3/4 male by netnetter444

...ions, so you'll need to have a good estimate of how much your pla contracts/expands and adjust your slicer settings for that.

thingiverse

free

E3D V6 Extruder Head Assembly With Cardan Shaft Direct Drive by astfaellergerald

...g vollständig ausgeglichen, deshalb ist darauf zu achten, daß die hebelarme zweier kardangelenke immer exakt in einer linie sind.

thingiverse

free

Mammut - Giant printer. by tahustvedt

...achment:https://www.banggood.com/10pcs-ac-250v-15a-v-156-1c25-spdt-roller-lever-micro-switch-p-944613.html?p=hd240528697332015103

thingiverse

free

Curta Calculator Mods by mcmaven

... digit, but then something else broke, and it stopped working all together. i have to tear it apart and find out what went wrong.

thingiverse

free

D-bot X/Y motion system linear guide blocks and pads made from Igus tribofilament by Rexipus

... source files for both blocks and pads. all of this is released with the creative commons - attribution - non-commercial license.

thingiverse

free

Belt Tension Adjust Truck for SeeMeCNC Ball Joint System and 1"x1" Extrusion by slonold

...ion truck at top, check tension at middle against fixed distance reference. tension at will!! gently snug screws when finished.

grabcad

free

Spherical Levers Coupling - 3 Lever Configuration

...simulation just to show that the coupling is indeed constant velocity. simply press the play button and open the output grapher.

grabcad

free

Cone Coupling (Clutch type)

...model was made for presentation purposes in engineering students. dwg plans have dimensions according to basic shaft diameter (d)

grabcad

free

Drum poultry feed mixer

...a simple drum poultry feed mixer that can be coupled to a motor or a hand lever for...

grabcad

free

Universal Coupling

...k to be performed on it. vises have two parallel jaws, one fixed and the other movable, threaded in and out by a screw and lever.