Thingiverse
TrackIR TrackClip PRO Battery Compartment Headphones Clip by falken_gt4
by Thingiverse
Last crawled date: 3 years, 4 months ago
With the addition of
1) 2 x CR2016 3v Batteries
2) Paperclip (or 1.25mm wire) for battery contacts
3) Micro toggle switch
4) 4 x spectacle size screws
you can get rid the USB lead for power and run cableless. (Some additional small lengths of wire might be needed to extend the wiring but can be harvested from the USB cable)
It works by removing the "twig" bit and it's extender from the original mount and wiring up through the switch with the original resistor onto the Clip Compartment. The lid is then held in with the 4 screws. The 2 x CR2016 batteries go on top of one another in the coin holder.
I designed it for my SteelSeries Arctic 5 headset but should work fine with most headphones
The Coin Battery holder part is a modified version from one I found on Thingiverse by NotSoSolid, I added some channels for the paperclip/wires to run through on the bottom allowing it to sit flat in the compartment.
1) Soldered the negative end of the battery terminal directly to the black negative wire going to the LEDS.
2) Solder the resistor to the positive end of the battery terminal and then solder the other end of the resistor to the switch.
3) Solder the red wire to the LEDs to the other terminal on the switch.
4) Make sure to insulate properly, I used heat shrink sleeving.
1) 2 x CR2016 3v Batteries
2) Paperclip (or 1.25mm wire) for battery contacts
3) Micro toggle switch
4) 4 x spectacle size screws
you can get rid the USB lead for power and run cableless. (Some additional small lengths of wire might be needed to extend the wiring but can be harvested from the USB cable)
It works by removing the "twig" bit and it's extender from the original mount and wiring up through the switch with the original resistor onto the Clip Compartment. The lid is then held in with the 4 screws. The 2 x CR2016 batteries go on top of one another in the coin holder.
I designed it for my SteelSeries Arctic 5 headset but should work fine with most headphones
The Coin Battery holder part is a modified version from one I found on Thingiverse by NotSoSolid, I added some channels for the paperclip/wires to run through on the bottom allowing it to sit flat in the compartment.
1) Soldered the negative end of the battery terminal directly to the black negative wire going to the LEDS.
2) Solder the resistor to the positive end of the battery terminal and then solder the other end of the resistor to the switch.
3) Solder the red wire to the LEDs to the other terminal on the switch.
4) Make sure to insulate properly, I used heat shrink sleeving.
Similar models
thingiverse
free
TrackIR TrackClip PRO Battery Compartment Headphones Clip by falken_gt4
...ing:48606 by notsosolid by adding channels for the wire/paper clip underneath to allow it to lie flat in the trackir compartment.
thingiverse
free
Amoeba LED Lamp-V1 by ChrisTheViolaNerd
...ints, and negative battery terminal will be wired to the (com) switch point. no wires will be connected to the (nc) switch point.
thingiverse
free
18650 holder 1S / 2S
...make sure they are correctly oriented. 1s instructions follow similar steps as described in the2s construction, however: solder two...
thingiverse
free
Simple CR2032/CR2016 battery tester by wavexx
... led on the negative.
fill with hot glue in order to improve stability of the battery contacts.
when cooled, glue the bottom cap.
thingiverse
free
Led right clip 1.2 by andrewchoi
...ingiverse
small clip to hold a led and batteries. works with 2 x cr2016 batteries or 1 x cr2032 battery. supports multiple leds.
thingiverse
free
Targa Pylon by FlynnD273
...fits onto the base from above, then you glue the pylon on top in the indent. the bottom of the base slots in and twists to close.
thingiverse
free
X Axis Alignment Tool for Creality CR10S V2 by xQuest
...lete it
2 3mm led
4 lr41 or ag3 batteries
2 resistors 150r or 220r
2 dip switch smd 6x6x6
some wire, solder paste, soldering iron
thingiverse
free
Associated B74.1 Battery Wire Clip 14ga by Cromulent_Designs
...-line components on the team associated b74.1 buggy.
slide wire through before soldering on battery terminals.
print on the side.
thingiverse
free
3D Water Pump by bygreenthumb
...casing.
remember to slide the battery clip wires through the holes of the top of the water pump before soldering the ends to the
thingiverse
free
Soldering Helping Hands by Marchie
...s. i used a pair of car electrical crimps but a pair of pliers would do the job.
the epoxy them into the holes in the base plate!
Gt4
thingiverse
free
Porsche 718 Cayman GT4 by MotoRider42HC
..." but there were a lot of problems. i've included the blender file, for anyone who wants to try and finish the repairs.
thingiverse
free
Halterung Impulsnehmer für Gaszähler GMT GT4 (IN UZ Sensor) by EinEinfach
...tz zum original lässt sich die halterung durch die zusätzlichen einkerbungen im unteren bereich zerstörungsfrei wieder entfernen.
thingiverse
free
Tamiya Ford Mustang GT4 LED Holder Front & Back Lights by Gardsef
...n das 3d modell spiegeln.
anschließend können die teile in die karosserie geklebt werden.
viel spaß mit licht an eurem mustang =)
thingiverse
free
Celica GT4 modified quick shifter bushings
... than the standard 7th gen bushings to remove the excess play.
i've printed this in pla not sure how long the part will last.
thingiverse
free
Rallyman GT Insert
...championship expansion pack 1 world tour expansion pack 1 gt4 expansion pack 1 gt5 expansion pack. you might be...
thingiverse
free
Simagic GT4 Vocore Screen by Iceman762
... it´s a simple creation.
maybe it works on another rims with 70mm quick release.
you need m4 screws.
i hope you have fun with it.
thingiverse
free
Toyota Celica T20 by KingerdreiD
...its a cover for a toyota celica t20 (gt) (gt4 (cfl = celica for...
Falken
thingiverse
free
Falken/G6 Axial Jeep Armor Fenders
...tes. print in your choice of settings. mileage will vary. i printed mine in a .15 resolution, and 30% infill. no supports needed.
thingiverse
free
Open
...open thingiverse inspired by volk te-37 wheels and falken tires. will fit open rc truggy ref: https://www.thingiverse.com/thing:42198 wheel...
thingiverse
free
WOPR - Greetings, Professor Falken License Plate Frame by beckerthorne
...by beckerthorne
thingiverse
wopr - greetings, professor falken - license plate frame
https://www.youtube.com/watch?v=nhwjlcairqo
thingiverse
free
Ace Combat - ADF-01 FALKEN by AceCombatant
... at 1:300 scale. not a 1:1 scale replica; the wings and other control surfaces have been thickened to print better at this scale.
thingiverse
free
Ace Combat - ADFX-01 Morgan by AceCombatant
...powerful aircraft, serving as the prototype for the adf-01 falken designed for printing at 1:300 scale for miniature wargaming....
thingiverse
free
SCX10 - MudGuard - FalkenEdition by BuckarooD
...t the rear have a special shape for the body so try them and tell me if you want an normal shape rear wheel wells
have a good day
thingiverse
free
ADF-01 Falken by alphaEJ
...oes not print properly just cut it off and use the pre-made one i made. please give my any feedback you can and/or tips thanks :d
thingiverse
free
Mothers Day Laser Cut Table Center by phhinkey
...24 acrylic sheet available on amazon prime. i used blue.https://www.amazon.com/falkendesign-bl2108-1-8-1224-translucent/dp/b01dysta3m/ref=sr_1_23?ie=utf8&qid=1494443541&sr=8-23&keywords=acrylic+sheets+12x24 ...
thingiverse
free
Predator Mask - HD Remix by Geoffro
...into zbrush and literally resculpting the entire thing using falken as the base - thats why this is a...
Trackclip
thingiverse
free
TrackIR TrackClip PRO Battery Compartment Headphones Clip by falken_gt4
...ing:48606 by notsosolid by adding channels for the wire/paper clip underneath to allow it to lie flat in the trackir compartment.
thingiverse
free
TrackIR ProClip magnetic battery mount by RussPitcher
...tyou change your mind so you can reassemble your trackclip pro with no more damage than a couple of...
thingiverse
free
TrackClip hat for Trackir by astfede
...ated 3 point trackclip for trackir or infrared webcam,
print at 0.2 infill 20% and apply 3 small pieces of reflective tape.
enjoy
thingiverse
free
TrackClip Pro Repair Clip TrackIR 5 by MakerHX
...p and forget about replacing anything ever again !
best of all: the joint is still fully working. adjust the arm to your liking !
thingiverse
free
Headphone case holder by truhlik_fredy
...14mm hole in the middle added, to support trackir trackclip attached to the...
thingiverse
free
Logitech G930 TrackIR TrackClip clip by whttigress
... for the official trackir trackclip to slide into. you will need support material for the channel the trackir trackclip sits in.
thingiverse
free
Bracket for broken TrackIR TrackClip Pro by etotman
...ir trackclip pro by etotman
thingiverse
the small plastic pieces inside my trackclip pro broke so i made this bracket to fix it.
thingiverse
free
TrackClip by kert
...nk tubes, mount the 3 leds on the trackclip_simple_part1, cable them in serie on a li-po or li-ion battery, and you're done!!
thingiverse
free
Powerbank for Track IR TrackClip PRO by FaFiii
...n inorganic lithium battery sl-760/t
added rings on the outside for zipties
added better suport for azdelivery tp5400 micro usb
Trackir
thingiverse
free
Rechargeable TrackIR clip by Tacticaltactics
...e how compressed those images were, so here's an imgur link with the uncompressed versions: https://imgur.com/gallery/2zijdqf
thingiverse
free
TrackIR TrackClip PRO Battery Compartment Headphones Clip by falken_gt4
...ing:48606 by notsosolid by adding channels for the wire/paper clip underneath to allow it to lie flat in the trackir compartment.
thingiverse
free
trackir pro no clip 18650 battery by speed100011
...e+protection dual functions tp4056 18650
to help you find the resitor value with the ir ledshttp://led.linear1.org/led.wiz
enjoy!
thingiverse
free
TrackIR Pro clip by l3vgv
...trackir pro clip by l3vgv
thingiverse
trackir5 pro clip, with correct sized and displacements.
thingiverse
free
PS3 Eye IR filter support by Korop
...ir filter to go on a ps3 eye for trackir ...
thingiverse
free
TrackIR by Korop
...port touching buildplate only for the trackir.
you'll find the arduino support here:https://www.thingiverse.com/thing:4771938
thingiverse
free
TrackIR ProClip magnetic battery mount by RussPitcher
...hone mount ensuring that the magnets face out, slide them together and hold in place for a few seconds until the glue has cured.
thingiverse
free
TrackIR Webcam IR CAP (Use tinted film) by gbechtinger
...nted separated.
use 5 layers of automotive window tint to make the visible light filter and let it pass the infra-red light only.
thingiverse
free
Steel Series Wireless Pro TrackIR 5 clip by loldielol
...lender, which is why it might look like crap xd but hey it does the job.
for better results, print on its side, with supports on.
Compartment
thingiverse
free
BOX - 12 compartments by MaNwE
...an prevent it:https://www.youtube.com/watch?v=fh1wuwy7hjw&t=203s
i cut of this extra material with curved knife and it was ok
thingiverse
free
Finder Spool Holder by spezzer
...spools which do not fit in the finder spool compartment in fact both the built in and this one...
thingiverse
free
Vertebrae with Secret Compartment by DaveMakesStuff
.... this means that you will need to use support and expect to do some post-print cleaning. a sanding wheel on a dremel works well.
thingiverse
free
Amazon Basics / Overture Filament Spool Half Box by thefrayedend
...this box, i am going to make a bigger compartment to go on the top eventually, not sure what...
thingiverse
free
150*150mm assortment box with 8 compartments by PetervdRiet
...riet
thingiverse
150*150 assortment box with 8 compartments.
25mm high, 33.75*70.50 compartments 24mm deep.
3mm sides all around
thingiverse
free
rapidstrike battery compartment door by NoahSane
... to my youtube channel!https://www.youtube.com/channel/ucgf0x3k4dgb5xxlyf3uksva
i plan to start posting 3d printing videos soon.
thingiverse
free
Caliper Box (Workzone) by PhilCraft
...there are two versions now. one extra with a compartment for a thread gauge (requested & model provided in...
thingiverse
free
UpBox New Extruder Parts by Nilye
...airflow from original fan and directs it to redesigned compartment (remove tiertime original casing) with gear and small ball...
thingiverse
free
Stand for LV61 Razor (Panasonic) by fificap
...oneblade stand, enlarged to fit the razor. added a compartment on the back to put the blade cover and...
Headphones
thingiverse
free
Headphone Rack for Coolermaster q300L by 3dmakerman1
...n the back of the pins for you to stick a 3 inch piece of 1.75 mm filament as a locking pin to make sure it doesn't fall off.
thingiverse
free
Headphone Stand by ciredigital308
...iverse
headphone stand for xbox, playstation, nintendo, or pc. holds most controllers in tray and 8 aa batteries.
tips welcomed.
thingiverse
free
Headphones Holder for P400 by polkastress
...the case. you will need both of the covered holes to be vacant, so this part probably won't work with a top-mounted radiator.
thingiverse
free
Quest 2 Headphone Adapter (Sony ZX110) by SolidRye
...want to break the bank. these cheap sony mdrzx110w headphones can be purchased pretty much anywhere for as little...
thingiverse
free
Headphone stand for beside table by dnlhrr
...eside table by dnlhrr
thingiverse
headphone hanger for beside table shickness is 19mm.
keep it super simple version of a hanger
thingiverse
free
Boss Waza Air headphone hook by jsaffer
...by jsaffer thingiverse headphone hook for boss waza craft headphones boss_waza_air_hook - under desk mount(receiver protrudes through the back)...
thingiverse
free
PC Case Headphones Stand by kenny0001
...he case with double-sided tape
there is a file with the nzxt logo, and without.
made to fit my arctis 7, but will fit many others
thingiverse
free
Headphones holder by Sup4K
... really complicated and very material expensive.
if you want to print this, it would take 1.50 hours and something like 75 grams.
thingiverse
free
Narrow Monitor Hook by ToyMaker62
...o. i've made a duplicate but left this one live, hidden in the system. i've asked support to fix that, maybe someday...
Pro
thingiverse
free
Magsafe Brodit adapter iPhone 12 / Pro / Pro Max with extra phone support by bjorntm
...2 pro i took a thickness of 2mm, so the total width of the phone incl. the case should be 82.1mm. please measure before printing.
thingiverse
free
Repair impeller for fan 40x40 Ender 3 Pro by Fracksinys
...blades on the impeller, then grind off any irregularities left after removing the blades, insert the rotor into the new impeller.
thingiverse
free
Anycubic Mega Pro - Cable Holder by daedalas1981
... flush on the print head.
left side of the cable holder now flat for easier install and removal of the assisted bed level sensor.
thingiverse
free
Spool Holder for Creator Pro by ItsDeCia
...ed to prevent the spool from falling off and the spool holder provides a simple, minimalist design that gets the job done.
enjoy!
thingiverse
free
Vixen GP Goto Conversion Using Meade DS Motors by wt808
...three m3 nuts, and reinstall the ring in the proer orientation again. press a mf85zz bearing into the recess...
thingiverse
free
Ender 3 Dimmer Switch Mod by polkastress
...and requires no mounting hardware. tested on ender 3 pro you will need: 1x potentiometer with switch. i used...
thingiverse
free
Bed Corner Spacer for Ender 3 PRO by LachyD5959
...iverse
this is a bed spacer for the ender 3 pro. it can go either under or above the original part named cablechain_bedcorner_v2
thingiverse
free
MYNT3D Pro Stand by CinemaTechnica
...ent, pla is probably okay, but i'd stay away from black because it absorbs heat.
check out my website, www.cinematechnica.com
thingiverse
free
Ender 5 Tool Box (Remixed for cable ties and scraper attachment) by 03togodwin
...stored. i have printed this on my ender 5 pro it is a fanastic small organiser too keep tools...
Battery
thingiverse
free
Oculus Quest halo strap cable clips by njozsef
...(thing: 3909976). simple cable clip for oculus-link or external battery ...
thingiverse
free
Oculus Quest 2 ADATA PT100 Battery Mount by hoobajoob
...e battery fitting very snugly in the flexible filament.
-- remixed from gilmarp's oculus quest xiaomi 10k mah battery adapter
thingiverse
free
DC adapter for ActivEnergy 20V power tools Li-Ion battery pack by suromark
...thingiverse
a connector to use the activenergy xyz561/2019sud 20v power tools accumulator as dc power source for hobby projects.
thingiverse
free
USB-C Powerbank with 18W fast charging by LivingroomWorkbench
...'s best to use protected batteries.
please note that i'm not responsible if you break something with this diy solution :)
thingiverse
free
Soyy NP-FW50 Battery Holder with Charge Indicator by meywue
...nd the little piece between the two grooves for the charge indicator so one can slide the indicator to change the charging state.
thingiverse
free
TBS discovery Battery stop by TurboCinqy
...s discovery battery stop by turbocinqy
thingiverse
battery stop.
prevents crashing your battery into your fc
30mm hole distance.
thingiverse
free
Dual lighted 40mm Objective Markers by Boardron
...now has a much bigger surface to glue the battery holder in place. the baseplate now has a design...
thingiverse
free
LG G5 extended battery spacer by enricorov
...t;legs" up.
full guide here: https://www.reddit.com/r/lgg5/comments/ecwp33/the_s7_edge_3600_mah_lg_xpower_4100_mah_battery/
thingiverse
free
Makita 18V Akku mount by Paku_ia
...paku_ia thingiverse this is a holder for makita 18v battery packs. the bracket can be expanded as required. also...
thingiverse
free
2020 Dumpster Fire Flickering LED by blownhemi
...but the clips inside should fit any two aa battery pack.. https://shop.evilmadscientist.com/productsmenu/792...
Clip
thingiverse
free
Extension Cord Cable Mount Clip by max_davis
...x_davis
thingiverse
cable mount that fits a standard extension cord cable (up to 9mm). just use two screws or nails to mount it.
thingiverse
free
Oculus Quest halo strap cable clips by njozsef
...ozsef
thingiverse
thank you gyozamonstah and mysteroius (thing: 3909976).
simple cable clip for oculus-link or external battery.
thingiverse
free
Wrist Roller Grip Training Tool by flakas
...a knot or two on the other side. then clip a carabiner onto the rope and attach some weight...
thingiverse
free
Screenprint Frame Spacer by thisdesignedthat
...screenprint frame spacer by thisdesignedthat thingiverse simple spacer that clip onto edges of frames (standard 40mm aluminum frame). i...
thingiverse
free
25mm Conduit Clip by sputnik72
...25mm conduit clip by sputnik72
thingiverse
just my design of a insta360 go camera mount for the diatone tinawhoop. super simple.
thingiverse
free
Delan Clip mount Bracket - Razer Kraken Headset by Fly-Boy-Rez
...p mount bracket - razer kraken headset by fly-boy-rez
thingiverse
dedicated mount for the delan clip to the razer kraken headset
thingiverse
free
EV100 Rubber Suit Top Mounted by shahirn
...prefer to mount the dvr on top instead of clip it on the side so i removed the clip...
thingiverse
free
Stabilo Boss Organizer by nick8m
...stabilo boss organizer by nick8m thingiverse a organizer to clip 8 stabiloboss together. note: the stabilos do not hold...
thingiverse
free
Di3play - Wanhao Duplicator i3 Plus LCD Display Enclosure by jinner
...levelling feet etc bottom plate which acts as retaining clip to install: remove bottom plate from printer to disconnect...
thingiverse
free
Classic Mini Engine Shield Clip by ThEGuRu81
...classic mini engine shield clip by theguru81
thingiverse
engine shield clip parta for classic mini