Thingiverse
InMoov Articulating Neck Joint ReMix by alansrobotlab
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a remix of Bob Houston's outstanding articulated neck mod.
https://www.youtube.com/watch?v=FPV6k8QfDY8
You'll need the following:
(3) 3m x 20mm socket head cap screws
(3) 3m x 12mm machine screws
(3) 3m washers
(7) #6 or #8 3/4" flathead screws or equivalent
(8) #4 1/2" flathead screws or equivalent
Print out every part with the following settings:
100micron layer height
6 perimeters
2mm tops and bottoms
15% infill
3-4mm brim
For ArtNeck_NeckV1 and ArtNeck_NeckUpperV2, I printed those with the same settings but with 250 micron layers. I just couldn't get the settings right to print NeckUpper at 100 microns.
Only these items will require supports:
ArtNeck_ServoHolderV2
ArtNeck_ServoJointUpperV2
Assembly
Drill out NeckUpper Ball Mounts to 2.5mm, then tap 3mm threads. Lightly sand the ball joints and attach to head using #8 screws.
Insert NeckLower into Neck with larger slot facing the back, align then drill, countersink and use a short machine screw to mate together. Make sure you shorten or snip the screw so that it doesn't extend into the neck. Mount new neck subassembly to InMoov with #8 screws. Mount Head NeckUpper to NeckLower. don't jostle.
Sand external surface of ServoPivot Mount point. Drill pivot hole to 2.5mm, then threads to 3mm. Use ServoPivot to drill out the mount holes from the shoulder frame. See photo. Put left servopivot into right facing inward, then drill for correct mount hole locations. countersink. To mount these, you're going to have to temporarily either remove the arm, or remove the rear shoulder panel. Mount using #8 screws.
Sand mating surface for ServoHolder. Drill pivot hold and servo mount holes to 3mm. Test fit into ServoPivot. Can/Should be tight. Mount to ServoPivot using 3mm washer and 12mm machine screw. Make very tight, turns out it doesn't need to pivot at all.
Drill PistonBaseSide to 3-4mm, temporarily mount to servos. Mount servos to ServoHolder using #4 machine screws.
Drill PistonBaseFront to 3-4mm. Remove neck front pistonbase, and temporarily mount to front Neck servo using #4 machine screws.
Enable neck front servo, and set to 90 degrees position. Grease up PistonBaseFront and balljoint. Test fit PistonFront attempting to mate with head level with floor. If all four orientations are either too high or too low, make a note of what change in rotation would be required to make head level (15 degrees, 45 degrees etc). Remove PistonBaseFront, unscrew horn and reset at desired position. Attach PistonBaseFront and try again. Use 20mm socket head cap screw to affix ball joint. Just turn head to side to access/affix front piston socket head cap screw.
Enable neck side servo, and set to 90 degrees position. Grease up PistonBaseSide and balljoint. Test fit PistonSide attempting to mate with head level with floor. If all four orientations are either too high or too low, make a note of what change in rotation would be required to make head level (15 degrees, 45 degrees etc). Remove PistonBaseSide, unscrew horn and reset at desired position. Attach PistonBaseSide and try again. Use 20mm socket head cap screw to affix ball joint.
Whatever control solution you're using, make sure you set sane max/min values for the new neck nod and side actions.
Enjoy! This is a very cool mod. :-)
Updates:
2016-02-28 NeckJointUpper to V3, widened mounting studs, shortened balljoint backplane for a few more degrees of freedom NeckJointLower to V3, thickened balljoint feature, now both slots are same size to match NeckJointUpper Added HK15328 servo horn if you're using that type of servo.
https://www.youtube.com/watch?v=FPV6k8QfDY8
You'll need the following:
(3) 3m x 20mm socket head cap screws
(3) 3m x 12mm machine screws
(3) 3m washers
(7) #6 or #8 3/4" flathead screws or equivalent
(8) #4 1/2" flathead screws or equivalent
Print out every part with the following settings:
100micron layer height
6 perimeters
2mm tops and bottoms
15% infill
3-4mm brim
For ArtNeck_NeckV1 and ArtNeck_NeckUpperV2, I printed those with the same settings but with 250 micron layers. I just couldn't get the settings right to print NeckUpper at 100 microns.
Only these items will require supports:
ArtNeck_ServoHolderV2
ArtNeck_ServoJointUpperV2
Assembly
Drill out NeckUpper Ball Mounts to 2.5mm, then tap 3mm threads. Lightly sand the ball joints and attach to head using #8 screws.
Insert NeckLower into Neck with larger slot facing the back, align then drill, countersink and use a short machine screw to mate together. Make sure you shorten or snip the screw so that it doesn't extend into the neck. Mount new neck subassembly to InMoov with #8 screws. Mount Head NeckUpper to NeckLower. don't jostle.
Sand external surface of ServoPivot Mount point. Drill pivot hole to 2.5mm, then threads to 3mm. Use ServoPivot to drill out the mount holes from the shoulder frame. See photo. Put left servopivot into right facing inward, then drill for correct mount hole locations. countersink. To mount these, you're going to have to temporarily either remove the arm, or remove the rear shoulder panel. Mount using #8 screws.
Sand mating surface for ServoHolder. Drill pivot hold and servo mount holes to 3mm. Test fit into ServoPivot. Can/Should be tight. Mount to ServoPivot using 3mm washer and 12mm machine screw. Make very tight, turns out it doesn't need to pivot at all.
Drill PistonBaseSide to 3-4mm, temporarily mount to servos. Mount servos to ServoHolder using #4 machine screws.
Drill PistonBaseFront to 3-4mm. Remove neck front pistonbase, and temporarily mount to front Neck servo using #4 machine screws.
Enable neck front servo, and set to 90 degrees position. Grease up PistonBaseFront and balljoint. Test fit PistonFront attempting to mate with head level with floor. If all four orientations are either too high or too low, make a note of what change in rotation would be required to make head level (15 degrees, 45 degrees etc). Remove PistonBaseFront, unscrew horn and reset at desired position. Attach PistonBaseFront and try again. Use 20mm socket head cap screw to affix ball joint. Just turn head to side to access/affix front piston socket head cap screw.
Enable neck side servo, and set to 90 degrees position. Grease up PistonBaseSide and balljoint. Test fit PistonSide attempting to mate with head level with floor. If all four orientations are either too high or too low, make a note of what change in rotation would be required to make head level (15 degrees, 45 degrees etc). Remove PistonBaseSide, unscrew horn and reset at desired position. Attach PistonBaseSide and try again. Use 20mm socket head cap screw to affix ball joint.
Whatever control solution you're using, make sure you set sane max/min values for the new neck nod and side actions.
Enjoy! This is a very cool mod. :-)
Updates:
2016-02-28 NeckJointUpper to V3, widened mounting studs, shortened balljoint backplane for a few more degrees of freedom NeckJointLower to V3, thickened balljoint feature, now both slots are same size to match NeckJointUpper Added HK15328 servo horn if you're using that type of servo.
Similar models
thingiverse
free
NEMA 17 Motor Mount by tetralite
... head cap screws of whatever length needed to fasten the mount to the device. the two mounting holes for the part are 28mm apart.
thingiverse
free
Gear Head Adapter by jeremyrichardmann
...e apart the gearhead native mount, the part with the ball-socket joint can be natively screwed into this with a proper 3mm screw.
thingiverse
free
Finger hinge by zerker77
...mounts. the hinge is designed for 3mx16mm bolt. the hinge mount has a hole and countersink, to accept a 3m socket head cap screw.
thingiverse
free
DSLR Tilt by LeoRover
...camera_holder side, then by two small m2 screws on the horn and then using m3x8 screws attach servo to the base. that's it ;)
thingiverse
free
Dash Mount with 17mm Ball by RealmKnight
..., etc or i drilled two holes to use m3 screws to attach it to the removable section of my jeep dash. v2 has the holes pre-drilled
thingiverse
free
Improved Ball and Socket Joint
... between the lobes, it's more like 90 degrees if you go against them.
the threaded designs can take considerably more weight.
grabcad
free
Socket head cap screw M8
...rks which doesn't have smart fasteners. the length can be selected during placement in the assembly and can be adjusted after
thingiverse
free
Bear head parts for 1/12 scale action figure by Shigeru
...bear head parts for 1/12 scale action figure by shigeru
thingiverse
you can use a 3mm ball joint for the neck. have fun!!
grabcad
free
BallJoint
...balljoint
grabcad
balljoint model for kira
updated mates to limit movement of ball
thingiverse
free
[3in1] Ball & Socket Joint with Screw Hole by DENOVATOR
...by denovator
thingiverse
ball joint & socket with thread hold. ball snaps tightly into itself. using 'm10x1.5' bolt.
Alansrobotlab
thingiverse
free
InMoov Chest: Kinect 2 by Scriptwerx
...and inmoov torso mods for the xboxone kinect by alansrobotlab this isn't technically a remix of the mindless parts...
thingiverse
free
Rostock Max OpenPnP Conversion by alansrobotlab
...easy to adapt to other larger format delta style printers as well.
i'll add in some basic instructions and a parts list soon.
thingiverse
free
InMoov Eye Mechanism 2 Helper Files (DEPRECATED) by alansrobotlab
...n brackets beefed up
uses printed servohorn (3mm bolt joint, beefier)
several parts slightly reshaped to increase range of motion
thingiverse
free
InMoov Torso Mods for the XBoxOne Kinect by alansrobotlab
... back.
2016-01-25 sensormount updated, fixed recessed screw holes
2016-01-24 recessed the sensor a bit more. frame parts updated
thingiverse
free
InMoov Stomach Helper Files by alansrobotlab
...dded recess for potholder. doh!
2016-01-25: tstomlowleft & right, deepened recesses for mount holes to stomsupport combined.
thingiverse
free
InMoov Stronger Shoulder Frame by alansrobotlab
...into position.
2016-02-25 updated pivmit to v3, added small recess to allow pivmit to slide into subassembly. added instructions
thingiverse
free
InMoov Stronger Bicep Frame by alansrobotlab
...ry well. haven't verified that the recesses for the front topcover are spaced correctly yet, everything else fits perfectly.
thingiverse
free
HK15328D by alansrobotlab
...ferent than the hitec servos, so you need to take that into account in your designs.
designed using onshapehttp://www.onshape.com
thingiverse
free
HK15338 by alansrobotlab
....
designed using onshapehttp://www.onshape.com
2015-10-27: quick update, put wire grommet on correct side and reuploaded models.
Inmoov
turbosquid
$29
inMOOV by Nina Lieven
...model inmoov by nina lieven for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1230519)
thingiverse
free
Inmoov Head Stand For Articulated Neck by Maverick_makes
...ons and piston bases, i haven't printed this myself yet, but let me know if it needs any tweaking. as always post your makes
thingiverse
free
V3 CICO Trainer by archieport
...assembly. remixes / attributions: -the face was based on inmoov skull v3 by mindless; www.thingiverse.com/thing:2081052 -the larynx was based...
thingiverse
free
InMoov Touchscreen & Raspberry Pi mounting by civrays
...c-raspberry-inch-capacitive-monitor/dp/b07qkt6l58/ref=sr_1_5?dchild=1&keywords=7%22+touchscreen&qid=1602617642&sr=8-5
thingiverse
free
Inmoov_Neck_Plate_V4 by Maverick_makes
...i wanted to get this all out there now that i have finished testing and printing everything.
thanks and as always post your makes
thingiverse
free
Customizable Servo Adapter / servo dummy by matthiasm
...(let's say you want to print the inmoov robot (www.inmoovfr), but it's too tall and you scale it to...
thingiverse
free
Geared Neck Mechanism for Sylvie 2021 - Low backlash! by TwinLizzie
...geared neck mechanism for sylvie 2021. loosely inspired by inmoov but approaches it in a completely different manner. designed...
thingiverse
free
servo m996r dummy by felenna
...servo m996r dummy by felenna thingiverse as inmoov builder you some times need to wait for parts....
thingiverse
free
Inmoov_Bust by Maverick_makes
...ieces grooves to allow you to run wires between the sections and back into the robot as well.
enjoy and as always post your makes
thingiverse
free
eye plates and links for Inmoov by Mindless
...eye plates and links for inmoov by mindless
thingiverse
testing,,, testing,,,,123
Articulating
3ddd
$1
Тумба Manhattan Hoff
... decodom
производитель: словакия
коллекция: manhattan
размер (шхвхг):65,1x131,4x41,6 см
материал:лдсп, мдф
цвет:белый, графитовый
3ddd
$1
Бесшовная текстура обоев
...есшовная
бесшовная текстура обоев из серии coswig augusta.
http://oboi.masterdom.ru/articul/4124-01-coswig-augusta/#!related=hide
3ddd
$1
Armchair_Atlas_Classic
...: сербия
размер (шхвхг):117x74х105 смhttp://hoff.ru/catalog/gostinaya/kresla/kreslo_classic_id432045/?articul=80259213
3ddd
$1
Dali Premium
...://hoff.ru/catalog/gostinaya/kresla/kreslo_dali_premium_id13060/?articul=80065162
кресло 55к треугольников, диван 108к.
3ddd
$1
стол RAINBOW
...tp://hoff.ru/catalog/kuhnya/obedennye_gruppy/kuhonnye_stoly/stol_rainbow_id172380/?articul=80098671
полигонов: 19 402
3ddd
free
Стол Woods. Стулья Labeo.
...а
цвет:чёрный, орехhttp://hoff.ru/catalog/kuhnya/obedennye_gruppy/kuhonnye_stulya/stul_labeo_id203788/?articul=80101237
3ddd
free
decor set (vases)
.../vazy_i_tsvety/vazy/vaza_sea_lion_id329173/?articul=80100737
there are little more that 1000 000 triangles in the set.
3d_ocean
$130
Caterpillar 725 Articulated Truck
...for close-up renders. scene contain textures, standart scanline, mentalray and vray materials. - high quality polygonal model ...
3ddd
$1
3 вазы из каталога hoff
...log/tovary_dlya_doma/dekor/vazy_i_tsvety/vazy/vaza_id17318/?articul=80088841
на троих чуть больше 40 000 треугольников.
3ddd
$1
письменный стол 0488 hoff
...cul=80095882
1830 треугольников. 3 материала, текстур нет.
из столов можно собирать рабочие места как на третьем скрине
Neck
3d_ocean
$5
Low Poly Giraffe
...low poly giraffe 3docean animal giraffe long neck low poly giraffe nature zoo animal low poly giraffe.crossy...
3ddd
$1
Porta Romana Cystal Strata Lamp GLB16
...textured surface is quite gorgeous and the beautifully sculpted neck can be finished in either brass or nickel plate....
3d_ocean
$9
Moscato wine bottles & full glass: Villa Pozzi
...wine colour. standing bottle with visible air in bottle neck and lying bottle...
3d_ocean
$19
Cartoon chicken RIGGED
...is rigged (hands, spine, pelvis, head, arms, legs, feet, neck. the scene in max files are exactly the same...
3d_ocean
$9
Pinot Grigio wine bottles & full glass: Bolla
...in bottle neck, and lying bottle with full bottle neck... ...
3d_ocean
$4
Sauna Pillow
...comfort contoured head health healthy hot laying model natural neck pillow relax rest resting rods sauna smooth steam steamy...
3d_ocean
$9
Chardonnay wine bottles & full glass: Milbrandt
...wine colour. standing bottle with visible air in bottle neck and lying bottle with full...
3d_ocean
$5
Deer Head
...3docean deer head simple model of deer head with neck ...
3d_ocean
$9
Sauvignon Blanc wine bottles & full glass: Apex
...wine colour. standing bottle with visible air in bottle neck and lying bottle with...
3d_ocean
$8
Cow Cartoon Character
...christmas hat on it’s head, a scarf around it’s neck and a big nosering. added these for fun....
Joint
3d_ocean
$29
Realistic Wooden Outposts
...very detailed realistic outposts built of wood and metal joint, medieval style. game ready. included files : package includs...
3ddd
$1
PENTA Joint
...penta joint
3ddd
penta
http://www.lampcommerce.com/en/catalogue/brands/penta-light/joint-floor-lamp
3ddd
$1
GRAMERCY HOME - INDUSTRIAL JOINT TABLE LAMP TL016-1-BRS
...strial joint table lamp tl016-1-brs
3ddd
gramercy home
gramercy home
industrial joint table lamp
tl016-1-brs
www.gramercy-home.ru
3ddd
$1
Лампа Timothy Oulton - Knuckle Joint Table Lamp
... knuckle joint
лампа от timothy oulton, стек не свернут.
размеры от производителя:
длина: 35 см
ширина: 35 см
высота: 63 см
3ddd
$1
GRAMERCY HOME - INDUSTRIAL JOINT FLOOR LAMP FL016-1-ABG
...strial joint floor lamp fl016-1-abg
3ddd
gramercy home
gramercy home
industrial joint floor lamp
fl016-1-abg
www.gramercy-home.ru
3d_ocean
$15
RobotX-JV1.0 Rigged
...robotx-jv1.0 this is a full rig robot model. no joint and animation. for the rigging system is the ik...
3d_ocean
$29
Dibot - Utility Robot
...utility bot of minimalistic aesthetics with unique rotating forearm joint. it is designed to be extremely tough and powerful,...
3d_ocean
$6
Truss Model Set
...models, including the joint pieces, including the tjoints and ljoint, ...
3d_ocean
$12
Exploded Half Axle
...axle 3docean axle chassis constant cv drive engine gearbox joint part planetary shaft velocity wheel an exploded half axle...
3d_ocean
$5
Engineering Fastner Pack
...engineering fastner pack 3docean bolt engine engineering fastner joint pack parts screw tool pack of engineering...
Remix
3ddd
$1
Barovier&Toso / Manhattan Remix 7192
... 004293-142405
в коллекции есть люстры 7, 9, 12 рожковые. диаметр соответственный 1000, 1250, 1500 мм.
3d_ocean
$5
Vray fabric Kvadrat remix green - tileable
...th vray and 3dsmax. high-resolution texture images (2000×2000 px) file included: shader vray 2.40 texture image 3ds max 2011 file
3ddd
$1
Muuto fiber chair
...grey/grey, dusty green/dusty green, nature/oak, natural white/oak upholstery options remix 183/black, remix 133/grey, remix 643/dusty red leather options black...
cg_studio
$49
HTC One Mini 2 Gunmetal Gray3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix gunmetal grey silver .max .obj .mb .lwo .fbx .c4d...
cg_studio
$49
HTC One Mini 2 Glacial Silver3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix glacial silver gray .max .obj .mb .lwo .fbx .c4d...
cg_studio
$49
HTC One Mini 2 Amber Gold3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix amber gold .max .obj .mb .lwo .fbx .c4d .3ds...
3ddd
$1
Barovier&Toso 7190-7195
...7190-7195 3ddd barovier&toso потолочнай люстра фабрики barovier&toso;, коллекция manhattan remix артикул 7190-7195. размеры в inches: 39"...
3d_export
$5
3D Locking Handle Weatherproof Storage Box Container
...handle weatherproof storage box container 3dexport new, improved and remixd! no screws required. print-in-place. weatherproof. parametric. 2 parts. easy...
3d_export
$10
multicolored remix parametric table furniture
... fbx, obj, mtl, archive with textures. the model has no glitches. render and materials - vray . without using plugins. good use!
3d_export
$12
remix yamaha rm1x
...remix yamaha rm1x
3dexport
geometry triangles 15.2k vertices 7.6k pbr no textures 1 materials 1 uv layers yes