Thingiverse
Filament roller experiment by spegelius
by Thingiverse
Last crawled date: 3 years ago
Update: I updated the rollers due to problems with almost empty filament rolls; they aren't heavy enough and the friction just tops them off the holder.
The new rollers are based on bearing idea I saw in Thingiverse some time ago. I didn't find the thing, but modeled my own. Rolling just fine. The model has tolerance of 0.1mm. Use horizontal compensation. feed rate etc. to make them print properly.
Wanted to test some ideas and needed better, adjustable filament roller. Soo I tested my ideas by creating this filament roller.
The roller parts need some lubricant, I used PTFE spray and/or some silicon grease. Still they don't roll too well in this application so I might replace them with something else. Doesn't seem to matter, filament rolls glide on them so it still works fine.
Highlights:
only printed parts
adjustable for different size spools
BOM:
4x axle.stl
4x washer.stl
4x nut.stl
4x roller.stl
4x foot.stl
1x big_nut.stl
1x frame_parts.stl
1x frame_nut.stl
1x shaft.stl
Assembly:
slide the feet to the frame parts. They can be quite tight, so use file or knife to remove materila if needed.
the rollers have their center printed as separate parts. Add some lubricant (PTFE spray) and pop them inside the rollers
same goes to the frame_nut, it uses same mechanism
install the long shaft using the big nut. Fasten it to the frame part that doesn't have the roller center
the frame part with the nut can be threaded on the shaft, moving the frame
each roller is to be fixed on the frame with axle, washer and nut. Washer should be in between the frame and roller
The new rollers are based on bearing idea I saw in Thingiverse some time ago. I didn't find the thing, but modeled my own. Rolling just fine. The model has tolerance of 0.1mm. Use horizontal compensation. feed rate etc. to make them print properly.
Wanted to test some ideas and needed better, adjustable filament roller. Soo I tested my ideas by creating this filament roller.
The roller parts need some lubricant, I used PTFE spray and/or some silicon grease. Still they don't roll too well in this application so I might replace them with something else. Doesn't seem to matter, filament rolls glide on them so it still works fine.
Highlights:
only printed parts
adjustable for different size spools
BOM:
4x axle.stl
4x washer.stl
4x nut.stl
4x roller.stl
4x foot.stl
1x big_nut.stl
1x frame_parts.stl
1x frame_nut.stl
1x shaft.stl
Assembly:
slide the feet to the frame parts. They can be quite tight, so use file or knife to remove materila if needed.
the rollers have their center printed as separate parts. Add some lubricant (PTFE spray) and pop them inside the rollers
same goes to the frame_nut, it uses same mechanism
install the long shaft using the big nut. Fasten it to the frame part that doesn't have the roller center
the frame part with the nut can be threaded on the shaft, moving the frame
each roller is to be fixed on the frame with axle, washer and nut. Washer should be in between the frame and roller
Similar models
thingiverse
free
Filament holder
...n testing stage.
required parts
8mm shaft
2x fl08 bearings
2x m5 bolts
4x m5 washers
2x m5 nuts
1x m3 bolt
1x m3 washer
1x m3 nut
thingiverse
free
filament spool roller base whith no metal parts by aquilito
...my remixed washer.
if the shaft doesn't fit well, heat the shaft and pinch it with pliers.
i feel happy if you post pictures.
thingiverse
free
Filament case / container by robertm1978
...l fi8
4x bearing 608zz
20x screw m3x16
20x nuts m3
1,5m 2/4 ptfe tubing teflon pipe
1x pc4-m6
parts to be cut from plexiglas 5mm
thingiverse
free
Filamentcutter 45° by utzoff
...ent cutter
insert the magnets so that they repel each other.
what is needed:
1x sk5 blade
4x magnet 8x3mm
4x washer 5mm
4x nut m5
thingiverse
free
60mm spool roller by NeK6683
...l stand for 60mm spool using 624zz bearing.
list of parts:
4x 624zz bearing
4x m3x20 screw
8x m3 washer
4x m3 nut
1x printed part
thingiverse
free
Ender 3 filament holder
... bolt
2x m8 nuts and washers
4x m3x10mm bolts
4x hammer nuts (i 3d printed them for use with a m3 nut)
2x 608z bearings (8x22x7)
thingiverse
free
Filament holder for the ultimate spool adapter by schnuffi
...are parts from your a8)
the print isn't nice, had some problems with this filament
update 2017-03-07:
added wider base plate
thingiverse
free
EXT3 Bowden 1.75 by Eldrid
...tubing 4mm od 2mm id (16mm, 12mm long)
2x ptfe fitting pc4-m6 (m6 screw, for 4mm ptfe tube)
1x mk7 drive gear for 1.75mm filament
thingiverse
free
Adjustable Filament Holder by Skyhigh24
... nut
4x ball bearing s695-2z
i havn´t printed it by myself. i just designend it for a friend.
so i dont know how good it works.
thingiverse
free
Dremel 3d45 filament cover with feedthrough by Printschnitzel
...dremel 3d45 filament cover with feedthrough use nylon or similar for the snatches bom to print: 1x deckel_mit_durchfuehrung.stl 1x...
Spegelius
thingiverse
free
XLite100 seat mount by spegelius
... mount and is attached to the seat with zipties.
openscad source here: https://github.com/spegelius/3dmodels/tree/master/xlite100
thingiverse
free
Tronxy X5S printed top frame extension by spegelius
...scad source for the frame can be found here: https://github.com/spegelius/3dmodels/blob/master/printerparts/tronxy/top_frame.scad
thingiverse
free
Prusa MK2/Dollo3D hybrid by spegelius
... 1.4
0.9 motors x and y
r3 extruder (needs small fw change)
230mm z (needs longer smooth rods to fully utilize the threaded rods)
thingiverse
free
PTFE M4 threading tool by spegelius
...e to free the m4 nut and pull the tube from the tool
as the ptfe tube compresses with the nut, i use 2mm drill bit to open it up.
thingiverse
free
Bowden dual/quad extrusion extruder (single-nozzle single-drive) for MG995 SERVO by serandre
...and prusa slic3r (1.36.2,1.37.1,1.38.6), you can download from here: https://github.com/spegeliusfilaswitch it prints perfectly, of course you need to fine...
thingiverse
free
B-Struder - E3D Hobb-goblin edition by spegelius
...rs but those should fit fine.
source code: https://github.com/spegelius/3dmodels/blob/master/b-struder_remix/b-struder_remix.scad
thingiverse
free
3D printed table legs by spegelius
...here in case you want to make changes to the desing: https://github.com/spegelius/3dmodels/blob/master/table_legs/table_legs.scad
thingiverse
free
Roller-brearing z-screw experiment (Dollo3D) by spegelius
...further development on this someday, like make this kind of a planet gear type where the rollers aren't fixed on the housing.
thingiverse
free
Slice Eng Copperhead fan shroud & mount by spegelius
...so i changed that.
source (openscad) can be found here: https://github.com/spegelius/3dmodels/tree/master/printerparts/copperhead
thingiverse
free
PanelDue case swiveling mount
...so i used wood screws to attach it. source: https://github.com/spegelius3dmodels/blob/master/paneldue_case_remix/paneldue_case_remix.scad ...
Roller
3d_export
$45
4 Bearing Collection 3D Model
...4 bearing collection 3d model 3dexport bearings ballbearing roller ball tapered bearing skf needle engineering gearbox engine car...
3d_export
$44
Ski lift station 3D Model
...mountain hill high sport train coaster railway sleding sled roller winter bench ski lift station 3d model download .c4d...
3ddd
$1
Roller Blinds
...roller blinds
3ddd
рулонная
roller blinds black out finish
3ddd
$1
Fino armchair
...with a chrome pillar or a 5-foot base with roller and can be height-adjustable on...
cg_studio
$15
Ski lift chair low poly3d model
...mountain hill high sport train coaster railway sleding sled roller winter bench machine .obj .max .fbx .3ds - ski...
3ddd
$1
Fino by COR
...with a chrome pillar or a 5-foot base with roller and can be height-adjustable on...
3d_ocean
$89
Building machines set
...roller roller building machines set include 3d models: asphalt roller ...
3d_ocean
$19
roller skate
...can scanned skates skating sport
3d scan of roller skate. the model has been retopologized and made fully compatible with zbrush.
3d_ocean
$39
Cans, spray and jerrycans of paint + RollerPaint
...quality realistic roller rollerpaint spray spraypaint tank tin varnish
cans, spray and jerrycans of paint + rollerpaint 10 models
3d_ocean
$19
roller skate
...pologized and made fully compatible with zbrush. subdivision levels (*.ztl): 1- 7,965 2- 31,860 3- 127,440 4- 509,760 5- 2,039mil
Experiment
3d_ocean
$15
Highpoly 3d Model of Electrostatic Machine
...3docean 3d charge current device discharge education electricity electrostatic experiment highpoly laboratory lesson machine mechanism mesh model physics polygons...
3ddd
$1
MART Sofa by Grado Design
...s supported by tubular legs that transform the sofa into something ethereal, almost floating in space.
dimensions:
w180 d79 h67
3ddd
$1
de sede \ DS-291
... tactile experience. combines perfectly with other furniture. also available with swivel star base.http://www.desede.ch
3ddd
$1
Bamboestoel Chair by Remy
...by means of just braiding the bamboo, but after experimentng they realized they wanted to use this technique to...
3ddd
$1
Carl HansenSon CH20 Elbow chair
...it makes an excellent desk chair. hans j. wegner experimentd with new materials such as moulded veneer, and the...
3d_ocean
$5
NR Design Ring 2013
...have more experient in autodesk maya. if you need more file type i am feel free for convert to you. model is ready for game mo...
3ddd
$1
OPPO | O52
...design-tool to configurate your own oppo!http://www.blastation.com/ after years of experimentng with the thin seat shells in laminated formfelt, in...
3d_ocean
$5
Binocular
...aces. ideal for use in games. model contains 3 textures with 1k resolution (as png and jpg format), color, normal and reflection.
3d_ocean
$5
CK Diamond Ring 009
...3d cad/cam designer that have more experience in autodesk maya, rhino, 3d max, matrix. if you need more file type i am feel fr...
3d_ocean
$30
Realistic Bedroom interior 3D
...interior 3d-contemporary design and rendered in vray. ” on experimentng with subtle textures, elegant furniture & soft glossy coating...
Filament
3d_export
$5
Buld 3D Model
...lightbulb lantern candle illumination streetlight electric light bulb incandescent filament lamp glow-lamp inc buld 3d model kiko 50448...
3ddd
$1
RIBBED GLASS FILAMENT SCONCE AGED STEEL
...к:
ribbed glass filament sconce aged steel
dimensions
8¾"l x 7¾"w x 7"h
в архиве файлы: 2013 max. fbx. 6 текстур
3ddd
$1
Restoration Hardware
...restoration hardware 3ddd restoration hardware моделилась с каталогаhttp://www.restorationhardware.com/catalog/product/product.jsp?productid=prod2111782&categoryid;=cat2250024 sputnik filament chandelier polished nickel...
3ddd
$1
Filament Cage
...filament cage
3ddd
лофт , filament cage
модель бра, делалась по фото!
3ddd
$1
METAL FILAMENT SCONCE
...conce
3ddd
restoration hardware , sconce
материал хром. размеры бра 216 мм*191 мм*171 мм
archive3d
free
Bulb 3D Model
...bulb 3d model archive3d bulb light bulb lightbulb filament lamp electric bulb bulb lamp standart n071015 - 3d...
3ddd
$1
Black&White set
...и металла. в бонус бра бра cone 20th c.factory filament артикул 44.009.mt.bl.t1b сталь латунь высота 16 см диаметр 21,5...
3ddd
$1
20TH C. FACTORY FILAMENT METAL SCONCE - POLISHED NICKEL
...toration hardware
restoration hardware
бра:
dimensions
8½"l x 7½"w x 6¾"h
в архиве:
2013 max
2010max
fbx
preview
3ddd
$1
20TH C. FACTORY FILAMENT RIBBED GLASS SCONCE - POLISHED NICKEL
...ration hardware
бра:
20th c. factory filament ribbed glass sconce - polished nickel
dimensions
8¾"l x 7¾"w x 7"h
3ddd
$1
Steampunk Pendant
...such. we've lamped it with a pair of edison-style filament bulbs for a softened light in the style of:...