23 tonymtsai 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Standin by tonymtsai
...standin by tonymtsai
thingiverse
....
thingiverse
free
Rockshox cable clamp by tonymtsai
...rockshox cable clamp by tonymtsai
thingiverse
cable clamp for front fork
thingiverse
free
Cable guides by tonymtsai
...cable guides for bike or anything else.
there is a standoff distance which i use to keep the cables from rubbing the swing arm.
thingiverse
free
Bike Cable Guide by tonymtsai
...onymtsai
thingiverse
work in progress. customisable for different cable widths. bike bar widths and multiple cables per guide.
thingiverse
free
Toughbuilt Tool Belt Hangers by tonymtsai
... to mount toughbuild tool pouches to the wall.
fast version does not have the latch part.
holds well even with a hammer on there
thingiverse
free
Rockshox Rebound adjuster knob by tonymtsai
... knob for rockshox forks.
adjust for your fork
uses a 2.5mm hex key
updated to have a longer grab in the middle for the key
thingiverse
free
circular blower by tonymtsai
...s mirrored
*updated to remove internal wall
*update to holes closer to one side be smaller than those further from the blower
thingiverse
free
Fan duct by tonymtsai
...r around the back of the fan.
better default size for the stl
more parameters for the scad.
vent supports to reduce sag from heat
thingiverse
free
Chain drop chatcher by tonymtsai
...
experience but it does make rounding edges much easier than in openscad. included the prt file so you can modify it if you want.
thingiverse
free
Minimalistic Endstop for 8mm Shafts Nut Trap by tonymtsai
...
thingiverse
simply added some small nut traps to one side. makes it a tiny bit easier to put together.
takes m2 nut and bolt
thingiverse
free
Customizable bit holder and screw driver by tonymtsai
... the number of bits and height of the driver as well as the size of the magnet you can place at the bottom.
go crazy!!!!!!!!!!!
thingiverse
free
Bash Guard Chainring by tonymtsai
...so set the bolts holes larger and fit a section of brass pipe in to prevent too much crushing force on the plastic from the bolts
thingiverse
free
Y axis idler tensioner by tonymtsai
... section in the scad file.
uses the m5 nut and bolt and two 625 bearings
tightening is done via a m3 nut and bolt at the back
thingiverse
free
Anti-Wobble and Backlash Z axis by tonymtsai
...ress the spring and install the bottom nut. after this is done, there should be a small gap between the top nut and the plastic.
thingiverse
free
Pipe Saddle Clamp with Buttrusses by tonymtsai
...e clamp part.
update ability to set the pipe to be lifted from the surfaceupdate automatic calculation of trust width
bracket
thingiverse
free
Simple Remix of Radus' excellent X Carriage by tonymtsai
... and two 625 bearings.
added the ability to install anti backlash z springs. (though i don't thing this is too necessary.)
thingiverse
free
Hinge Mount for Dual Articulated Ball Joint Fan Mount by tonymtsai
...printed from http://www.thingiverse.com/thing:119616
and changed it so the nuts are not encased in the arms.
uses 40mm fans.
thingiverse
free
Mini Grease Gun Adaptor by tonymtsai
...he tube.
2.fitting the tube
loosely screw the tube to the gun. squeeze until grease comes out the side and then fully tighten.
thingiverse
free
Nissan Leaf Strut Cap by tonymtsai
...actors.
if someone has an original cap on hand and can measure the dimensions of the clips for me that would be really useful....
thingiverse
free
Low profile anti wobble / anti backlash system for prusa / logresse by rcoolen
...is 13mm instead of 23mm for the one from tonymtsai another 2mm could be shaved off if the bottom...
thingiverse
free
HICTOP Circular Part Cooler and Leveling Sensor Mount by tcm0116
...sensor mount by tcm0116 thingiverse i was inspired by tonymtsai#39;s circular blower design to create my own for my...
thingiverse
free
Saddle clamp/PVC pipe antenna mast mount by jaymzx
...cement and a 1/2" pvc pipe 'mast'. i took tonymtsai#39;s clamp and added a bit of width to it...
thingiverse
free
Grooved acceptance by shivinteger
...[2] thing url : http://www.thingiverse.com/thing:720177 [2] thing author : tonymtsai [2] thing licence : creative commons - attribution -...