20 mspencer 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Cocoa decor caster with mystical pattern :-) by MSpencer
...ith mystical pattern :-) by mspencer
thingiverse
little cocoa caster which i have made just for fun in my early 3d-printer days.
thingiverse
free
Abdeckung für Meanwell Netzteil am Vertex K8400 by MSpencer
...ung für meanwell netzteil am vertex k8400 by mspencer
thingiverse
kleiner cip für die spannungsführenden klemmen am vertex k8400
thingiverse
free
RS232 Sniffer and Forwarder Housing by MSpencer
...ing communication (man-in-the-middle)
???
you can find the files for soldering here:http://www.keinschnickschnack.de/?page_id=772
thingiverse
free
Teutonia BeYou KiddyBoard clip by MSpencer
... or some other non-pla stuff (nylon, colorfabb xt).
pla is too brittle for this. i had great durable results with colorfabb xt.
thingiverse
free
Pollin case enclosure geiger counter by MSpencer
...the tube while the counter is running ( high voltage!).
0.15 to 0.25mm slices with a 0.35/0.4mm nozzle should work fine with pla.
thingiverse
free
Vellemann Vertex K8400 spool mount socket by MSpencer
...of space on each side of your printer.
screws, nuts and bearing used are the same as the original one. you can reuse these parts.
thingiverse
free
Lego Duplo steam train front piece replacement by MSpencer
... flow rate for maximum precision.
on my vertex k8400 i had to enter 72% flow for a tight fit and to meet all the distances width.
thingiverse
free
32mm spool mount for Vellemann Vertex K8400 by MSpencer
...ulmann nylon spools. please check if the 32mm diameter is still valid or if your spools have an even smaller center diameter now.
thingiverse
free
Coin paper roll helper - stack coins and slide a paper under them by MSpencer
...ther currencies, too.
it prints upright with no need for supports.
print with 0.15..0.25mm precision with a 0.35 or 0.4mm nozzle.
thingiverse
free
K8400 fan shroud duct clip MK2 - no screws needed by MSpencer
...ly to the front.
currently the design applies only for one (right) printhead.
looking forward to attache more photos and so on...
thingiverse
free
Magnetic paper scroll holder for notes and shopping list by MSpencer
...en they are thicker it should still be ok.
it helps to put some thick paper in the back of the scroll. this makes writing easier.
thingiverse
free
Filament (1.75mm) force measuring hook for tension spring balance by MSpencer
...i changed the extruder and gear to an mk7 type.
therefore the initial force from 45n (4,5kg) was improved to more than 70n (7kg).
thingiverse
free
Pollin Roulette case enclosure with 9V battery holder by MSpencer
...too tight in there.
can be printed completely without supports and does only need a bit or maybe no rework at all after printing.
thingiverse
free
Daihatsu Cuore Toyota Yaris MY2007 washer water cap by MSpencer
...for nylon prints i do recommend a brim for better sticking to the build plate.
print resolution should be less or equal to 0.2mm.
thingiverse
free
Spaceing and accuracy test cylinder print down to 0.15mm by MSpencer
...m and an accuarcy of 0,05mm for the overall block as well as a nice closed surface.
but this took a lot of calibration effort....
thingiverse
free
Kettler Dreirad Griff - Kids trike grip handle from flexible fillament by MSpencer
...ing it with a thick wall (three layers of 0.35mm -> 1.05mm) and only 10% infill.
the result was a very soft and spongy handle.
thingiverse
free
Travelbox for XCite Rocket RX 65XS (old and new version) by MSpencer
...al power connectors. i replaced them so i can
use a bunch of cheap chinese lipo batteries instead of the expensive original
ones.
thingiverse
free
Case for Electronic Load Battery Capacitor Tester found on eBay by MSpencer
...he pcb
3) mount the 4mm jacks (10mm hole already in there) and solder the wires
4) plug in the 12v power jack and start using it.
thingiverse
free
IKEA Trofast drawer stopper for the pine wood version or bracket or corner piece by MSpencer
...a printed it nice and easy without any problems.
you may want to under-extrude (reduce flow) so that the 3mm screw fits in there.
thingiverse
free
K8400 fan duct clip - no screws or glue needed by MSpencer
...is minimized when winding some kapton stripes around it - see images.
can be printed without supports - see print settings below.