26 doer 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Backplate for HC-SR04 Mount by Doer by Grey3000
...on backplate for doer's hc-sr04 mount, i've included the freecad file in case you want to add a mount point or something.
thingiverse
free
Lidar lite to actobotics mount by Doer
...lidar lite to actobotics mount by doer
thingiverse
needed to mount lidar to actobotics c-channel strut.
thingiverse
free
DS18B20 temperature sensor holder by Doer
...erature sensor. base is 40 x 60 mm. sensor is about 6 mm diameter. one hole is bigger to accommodate to heat shrink wrapped part.
thingiverse
free
Lidar Lite Lens Cap by Doer
...n i am not using it. it works pretty good as is, but i may try to improve it in the future. i made it using 100% infill. lasers!
thingiverse
free
CPAP forehead pad by Doer
...ht. unless you want a dented forehead, this is for flexible or tpu filament.
legal disclaimer; don't do this, blah blah blah.
thingiverse
free
HC-SR04 mount by Doer
... in the corners to hold it in place.
bonus! here is a matching back cover by grey3000,https://www.thingiverse.com/thing:2320430
thingiverse
free
Engraved 2001 Monolith by Doer
...of where it came from was in order. anyway it is 1 cm by 4 cm by 9 cm. and you better make it black, and stay away from europa.
thingiverse
free
RJ45 splitter holder by Doer
...j45-connector/step2/establishing-cat-5-standard-for-temp-sensors/
the base is 40 x 60 mm. the rj45 splitters are ebay cheapies.
thingiverse
free
Magnetic Tool Holder by Doer
...rong enough to hold up the tool holder loaded with tools. maybe with n52? anyway, i screwed it to the desk and it works good now.
thingiverse
free
LED strip holder by Doer
... do not show up in the rendering above. i made this for the non-waterproof strips and have not tried it with the waterproof ones.
thingiverse
free
Magnetic fan mount holder by Doer
...jmagnetics.com/proddetail.asp?prod=r622cs-n the magnet bolts are flat head #4 x 3/8", the rest of the bolts are regular #6.
thingiverse
free
Easy Grasp Refrigerator Magnet by Doer
...deally it should stick out very, very slightly, if it is pushed in even a little bit too far, it loses much of its holding power.
thingiverse
free
LED strip holder with landing pads by Doer
...r the non-waterproof strips, have not tried it with the waterproof ones. the screw holes are for #4 x 1/2" flat head screws.
thingiverse
free
Expander for copper plumbing by Doer
...o outside cones are pla. all parts are printed slow with 100% infill. you need to print two flexible tpu parts and two pla parts.
thingiverse
free
Binocular Eclipse Solar Filter by Doer
...hould be sandwiched between the ring and the inside of the housing. waves and minor wrinkles are ok, creases or holes are not ok.
thingiverse
free
Dual Laptop Power Supply Holder by Doer
...ith #6 x 1/2" screws. i have the power cord going down and the computer cord going up. the overall size is 145 x 39 x 75 mm.
thingiverse
free
Magnet attachment for broom handle by Doer
...one https://www.kjmagnetics.com/proddetail.asp?prod=mms-a-x8
also found out they have a good selection of magnets at home depot.
thingiverse
free
18650 magnetic holder for charging by Doer
...mal charge rate for the 18650 batteries i have is 1.25 amps. you do not need the balance leads if you are charging a single cell.
thingiverse
free
LED 8 mm strip magnetic mount by Doer
... them in to the printers main power. it lights up the bed nicely. no supports needed. i used paramount 100m matte black filament.
thingiverse
free
Mecha suit by zekerob1
...combine into a mecha ready to take on any evil-doer it may...
thingiverse
free
LED strip holder with landing pad (15mm) by turboscirocco
...just a wider version of the one supplied by doer i needed one for 15mm strips so i widened...
thingiverse
free
LED strip holder2 by norwestie
...holder2 by norwestie thingiverse this is a remix from doer i added a flat section to the bottom to...
thingiverse
free
MakerBot Damsels by MakerBot
...damsels distribute production precisely for punctual perfection. dastardly deed doer and nefarious ninja gnomes beware, the damsels don’t take...
thingiverse
free
Rudog dual extruder or single by yourwildworld
...by yourwildworld thingiverse rudog, vigilantly guarding the presents from no-good-doer like krampus, and keeping an eye on the sky....
thingiverse
free
Heman Sword electronic MOTU by thinkpool
...the universe fans! need to shoo away some evil doer well i have the perfect thing for you. the...
thingiverse
free
Costume Power Lights
...the collar. flip on the lights, and destroy galactic evil-doer. (post halloween follow up... bracelets worked great. clasp didn't...