18 Px4Flow 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
PX4Flow by memmop
...px4flow by memmop
thingiverse
mount for px4flow. will sit 10mm below mount plate.
thingiverse
free
Px4Flow Mount by MORP
.... as sold on ebay. therefore i updated the original design. it now does fit the sensor and it provides an additional cover plate.
thingiverse
free
PX4Flow cover by AmperCZ
...on't use.
it needs some tuning after print and there is missing hole for usb connector in top part. will update after tests
thingiverse
free
A2USA and W&L CIT PX4Flow mount for Iris by B__
...mmonwealth research commercialization fund slam project. the mount was designed to accommodate a px4flow unit mounted to an iris.
thingiverse
free
Bixler 3 underside pod for px4flow and Teraranger LiDAR by H4v4rd
...rts for securing the sensors and 5 short m2 screws
the threaded inserts can be inserted by using a soldering iron to melt the pla
thingiverse
free
PX4FLOW Mount for X8 3DR UAV Version 1.0 by JudeLabs
...tached the openscad file if you need to do additional adjustments.
new version is in work that provides a bit more protection.
thingiverse
free
PX4 Flow case by jgoppert
...e crash resistant so that impacts won't damage the camera. it is also designed to block prop noise for the ultrasonic sensor.
thingiverse
free
PXFlow Mount by simondlevy
...nd 5mm standoffs allow you to remove the unit as needed. you can glue the mount to the bottom of your vehicles frame with e6000.
thingiverse
free
A2USA and W&L CIT SLAM Mount for Iris by B__
...am project. the mount was designed to accommodate an odroid linux computer connected to a hoku urg-04lx lidar and a px4flow unit.
thingiverse
free
TBS Discovery Endurance Backpacks by Ghost_3D
...2 has the same dimensions).
updated 30/01/16 - rolled the separate discovery / discovery pro plates into single universal plates.
thingiverse
free
"The Flying Box" - A 280mm Modular Quadcopter for 6" Props by bkahan
... holes
adjust standoffs for new fc (pixracer)
add support for gps mount
fpv
create 'racing' middle stack (remove rpi3)
thingiverse
free
NANDRONE QUAD 2017 by nandinho84
...botix-%2f112299247099%3fhash%3ditem1a258e85fb%3ag%3amiqaaosw4cfynfag)
more info, photos and instructions to build this quad soon.
thingiverse
free
Shower strapped to small Chip by shivinteger
...51
[+] cleaning non manifold
[!] total removed v: 0.00%, e: -0.00%, f: -0.00%
[>] exporting stl to : /uploads/20160223-1800-22
grabcad
free
PX4Flow Case
...ou need four hex offsets (m3 x 20mm) and four screws (m3 x 10mm). additionally, you can use an m12 cable gland for secure wiring.
grabcad
free
ETH PX4Flow Optical Flow Module
...dirty mockup of the px4flow pcb, sonar and lens assembly. no components are populated yet, perhaps in the next revision... enjoy.
grabcad
free
A2USA and W&L CIT PX4Flow mount for Iris
...mmonwealth research commercialization fund slam project. the mount was designed to accommodate a px4flow unit mounted to an iris.
grabcad
free
A2USA and W&L CIT SLAM Mount for Iris
...am project. the mount was designed to accommodate an odroid linux computer connected to a hoku urg-04lx lidar and a px4flow unit.
3dwarehouse
free
PX4FLOW v1.2
...px4flow v1.2
3dwarehouse
px4 autopilot project px4flow board #px4flow_px4