21 Klave 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Dremel Nut by Klave
... scaled 101% in the radial directions to make the fit slightly looser but 100% threaded on fine
lay it on its front face to print
thingiverse
free
LM2596 Enclosure by Klave
...he board. the lid will fit both ways so make sure you check the pot is visible.
for the side entry the lid will only fit one way
thingiverse
free
YAFS Yet another end of of filament sensor by Klave
...x 5.7 mm like these https://www.amazon.ca/gp/product/b07dgx9b9c)
it also doubles as an equally unnecessary filament guide
ender 3
thingiverse
free
Filter Sieve by Klave
...s, the bars are an easy distance to bridge, only 3.6mm, and the sides taper at 24 degrees from vertical so no supports are needed
thingiverse
free
Hex bit finger wrench by Klave
...tool holder so i can easily place and remove it. i also put a magnet in the wrench top to stick it to the nearest piece of steel.
thingiverse
free
CNC Tool Probe by Klave
...e that theirs is normally open and they had to set the probe as active low. this is not needed for my probe which is active high.
thingiverse
free
Honda Civic 2008 Front Emblem by Klave
...ted it, i just made a curved version of the flat one and added the two pins, about 2mm long. you will need supports for this one.
thingiverse
free
K40 mA meter Bezel by Klave
...high voltage on them.
the meter face is 56mm x 64mm and the large round section has a diameter 49mm
mine is similar to this meter
thingiverse
free
Zero Probe by Klave
...rotrude past the print head then you could use it but there are many available options for bed leveling that don't need this.
thingiverse
free
K40 mirrors by Klave
... had this experience, feel free to feed back to the mirror suppliers that their compatibility with k40 is marginal and deceptive.
thingiverse
free
2032, 2025, 1616 coin cell storage by Klave
...he embossed size because that can't be specified in the parameters but the space is there to write on with a permanent marker
thingiverse
free
LR44 Button Cell Holder by Klave
... quite big and holds 10 cells. if you want a long narrow one then this one will fit nicely into a drawer and also holds 10 cells.
thingiverse
free
Stepcraft CNC tool adapter by Klave
...it to your own tools. i have bought low cost dremel tools like the 9929 bit or carbide point bide tungsten steel engraving bits.
thingiverse
free
K40 Height Adjust by Klave
...n't turn when adjusting or the height will be inaccurate and it may come loose at the end.
print time was 5 hours on my e3 v2
thingiverse
free
12V Ozone Generator by Klave
... is supposed to hold the board down by pushing on the pot, if your printer leaves a blob of material on it then just file it off.
thingiverse
free
Water flow switch by Klave
...rs, red and green if you want the filter to work, the outer wires don't get filtered and so have lower electrical resistance)
thingiverse
free
K40 Y axis idler pulley by Klave
...gs but they arrived too late
in the end it works fine, i think a toothed pulley would be smoother and these you can buy or print.
thingiverse
free
16mm CO2 Laser Alignment tool by Klave
...be. looks like a good idea to me but i haven't tried it. i don't have space to plug it in between the mirror and laser:-(
thingiverse
free
Air assist pressure filter using pop bottle by Klave
...uching the bed, don't want to fill the internal plumbing with support material!
it leaks air because printed parts are porous
3dwarehouse
free
Klaves
...klaves
3dwarehouse
3dwarehouse
free
Dhai Klave - Tumultuous Jade WindWalker
... item, thanks! ;-) #dhai_klave #exhalted #exhalted_second_edition #exhalted_swords #exhalted2e #sword #tumultuous_jade_windwalker