46 Jos310581 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Caddx Turtle SD Card Protector by jos310581
...ctor by jos310581
thingiverse
was worried about my sd card popping out so designed this for my acrobrat to ensure it staying in.
thingiverse
free
Chaos 20A Esc Protector V2 by jos310581
...s310581
thingiverse
v2 of my esc covers designed to fit chaos 20amp
https://www.unmannedtechshop.co.uk/chaos-blheli_s-dshot-esc/
thingiverse
free
Garmin to Lezyne adaptor by jos310581
...to print with a raft and use support with a roof
doesn't require anything complicated like soluble supports
nice a tight fit
thingiverse
free
Capacitor Support for Thor 210 by jos310581
... i wanted to support it from any knocks, this just helps keep it secure and supported by the stand offs, center to center is 22mm
thingiverse
free
FLEX RC Pico X Stand by jos310581
...e stand for keeping you pico x on, designed to take any 88mm frame and designed to use the battery mount or just sit on the arms.
thingiverse
free
FitBit Blaze Charging Cradle by jos310581
... couldn't find a stand for the charger just the actual fitbit itself so i designed this one, hope some people find it useful.
thingiverse
free
GoPro Mount Plate For Thor 210 Quad (Untested) by jos310581
... plate for thor 210 quad (untested) by jos310581
thingiverse
just an experiment as i couldn't find a mount for my 210 frame.
thingiverse
free
Fatshark Nano-Tech 1000mAh Case by jos310581
...my nano-tech 2s 100mah battery slipping out of my head strap and to match my stock fatshark one so it fits in the strap securely.
thingiverse
free
Drone Building Tools Stand by jos310581
...wall mount where you can keep them safe but also take out onto the bench when required.
https://www.unmannedtechshop.co.uk/tools/
thingiverse
free
Chaos 20A ESC protectors by jos310581
...emove this cover whilst the esc is wired in. kept my esc in the shrink wrap it came with and mounted on some self adhesive foam.
thingiverse
free
Ummagawd Remix Skids by jos310581
...epends really on what fc you use (matek f405 for me) so again you might need to edit to place the usb where you require it.
enjoy
thingiverse
free
Runcam Micro Sparrow 2 Pro by jos310581
...sign a cover/protector just to protect the lens in a crash without coming into the view of the fpv experience.
print in tpu @ 0.2
thingiverse
free
Foxeer TM25 MRM Edition mount by jos310581
... it covered the nice mrm cut into the carbon so i added this to the top of the print and also added a zip tie hole to look neater
thingiverse
free
FLYSKY FS-i6 Wall Bracket by jos310581
...ed really good, all did was add a groove for the handle to rest in so it was secure, can also hang your goggles off if you want.
thingiverse
free
Anycubic i3 Mega TPU Filament Guide by jos310581
...so soft it tends to go into the extruder at an angle so created this to allow the filament to go into the extruder nice and true.
thingiverse
free
Thor 210 Foxeer V3 Mounts by jos310581
...ded...one for standard standoff's and one for tapered standoff's
added version 3 for use with omnibus f4 pro corner board
thingiverse
free
Diatone GT-R5 Arm Bumpers by jos310581
...e scale and width differs.
helps protect your motors and carbon from damage without having to get longer screws
print in tpe/tpu
thingiverse
free
MRM Micro Reaper Bottom Plate by jos310581
...'t press into the battery and also wanted to secure the battery lead off the pdp so the pads didn't get ripped in a crash
thingiverse
free
Ummagawd Remix GoPro Session Mount by jos310581
...uses the existing hardware minus the two side braces.
i also had to remove the lower lip as this interfered with my fpv cam
enjoy
thingiverse
free
Ummagawd Remix TBS Crossfire & SMA Mount by jos310581
... the immortal t and a slighting thicker one to secure the sma against the top plate, also has 'remix' on the plate.
enjoy
thingiverse
free
DYS Mi200 VTX cover for MRM Micro Reaper by jos310581
...aper, has funnels front and rear to allow for air flow and is held in place with the m3 screws spaced 30.5mm apart for the stack.
thingiverse
free
Thor 210 GoPro Session 23 degree mount by jos310581
...10 quad and till allow the vtx to install on the top plate, should fit any quad-copter with 25mm standoff spacing.
23 degree tilt
thingiverse
free
Nissan Juke_Wismec Predator 228 Cup Holder V2 by jos310581
...verse but none where right for the nissan juke so designed this which works a treat. design with or without wording so up to you.
thingiverse
free
FrSky 30.5mm XM+ Stack Holder by jos310581
...rsion that sits slightly lower for a low profile build and sits further in if you find it obstructs anything like camera tilt etc
thingiverse
free
Diatone GT-M5 (200) FPV Camera Support by jos310581
...pport friction fits in both sides of the cage and support the camera to stay at a constant angle (around 30 degrees in this case)
thingiverse
free
Taranis QX7 Arm/Disarm Switch by jos310581
...t is sturdy, rigid and easy to print in pla. hope it helps some of you out there.
please note you will also require a 2mm zip tie
thingiverse
free
RunCam Micro AIO 20X20 Mount by jos310581
...tenna comes up.
could do with more height to allow more tilt as the vtx bottoms out on the rear screws but fine for indoor flying
thingiverse
free
Thor 210 GoPro Session Mount V2 by jos310581
...hing simple with a rubber velcro strap, tested this one a fair bit before putting on to thingiverse and haven't broke it yet.
thingiverse
free
THOR 210 frame Protectors by jos310581
...lthough secure so i added some foam tape to the end of the arm and pushed over the top. if they break on impact you can re-print.
thingiverse
free
Anycubic i3 Mega LED remote holder by jos310581
...p.
designed so you can mount left or right, print standing up right.
hope this helps some of you before you loose that remote....
thingiverse
free
Taranis QX7 Botgrinder Gimble Guard with clip by jos310581
... bracket. i haven't printed v4 however my v3 fitted fine i just had to make a couple of small tweaks so v4 should be perfect.
thingiverse
free
Thor 210 GoPro 3/HD5W Mount by jos310581
...rear, then use velcro strap to hold on. works really well and have done at least 6 flights with flips and rolls without any issue
thingiverse
free
Fatshark Case Wall Mount by jos310581
...unt.in hind sight the i should of spent some more time refining the fit (angles) and adding a log but t does work very well as is
thingiverse
free
FrSky QX7 Battery Tray Adapter for Turnigy Nano-Tech 1000mAh battery by jos310581
...ery spare and created this so it can power my qx7 and not wobble about, also created a cut out to make plugging in and out easier
thingiverse
free
Fatshark Attitude V4 Screen Protector by jos310581
... happy and they fit so well you can actually pick up the googles using the them (wouldn't recommend this for obvious reasons)
thingiverse
free
Diatone GT-M200 Antenna Mount by jos310581
...ee angle in addition to what the rear stand offs already have for a slighting better position on your antenna away from the props
thingiverse
free
Diatone GT Series Arm Bumpers by jos310581
... over the arm and do not require and additional screw length, work well with bottomless motors.
print only in tpu or tpe
enjoy...
thingiverse
free
200mm 3D Printed Quadcopter by jos310581
...e post.
this was all printed in the pla other than the antenna adapter but i had that in my dec kwad box which was tpu.
enjoy....
thingiverse
free
Mini Quad Grass Launcher by jos310581
...so the quad butts up against to the arm tabs, if you wanted to increase the legs and tilt more it might work ok for track racing.
thingiverse
free
FrSky Taranis QX7 & QX7S Stand & Wall Mount by jos310581
...o i designed a new wall mount to accommodate.
i used m3 motor screws (think 12mm) and stand off nuts fitted well into the slots.
thingiverse
free
Diatone GT-R5 Cap holder/FPV Cam mount/SMA mount/GoPro Session mount by jos310581
... way i wanted to mount certain things, all printed in tpe or flex pla.
all mounts set at 30 degrees
hope this helps some of you.
thingiverse
free
TBS Crossfire Mounting Brackets for Diatone GT-M200 by jos310581
...model on the slicer, mirror on the x axis and turn 180 degrees to get an opposite pair. best to print as per my cura screen shot.
thingiverse
free
Diatone GT M-200 GoPro mount with built in VTX holder for Foxeer TM25 Switcher by jos310581
...eed a battery strap of at least 400mm to fully wrap round.
update 31/03/2018 added a revised slimmer version which i am now using
thingiverse
free
Fatshark Attitude V4 Furious True D Cover Secure Bracket by jos310581
...on the sma adapters doesn't make the pins in the module bay lose power to the module. hopefully some of you find this useful.
thingiverse
free
15 Degree Mount for SQ11 & 12 to fit 30,5mm Stack & House VTX by jos310581
...pinning 3 inch props on a 3s should be fine, if its not and i change the design i will upload any updates on this page.
enjoy....
thingiverse
free
Clip-on Flysky I6/I6X gimbal and Switch Protector by NathanMichaelMoore
...-18: added version without tops for easier printing and also uploaded a step file for easier editing if people want to customize.