15 Jasoncanning 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Paint / Liquid Mixer by Jasoncanning
... using at least 5 walls when printing this to keep the shaft strong. i used petg and it works great.
https://youtu.be/8z0kfmylie8
thingiverse
free
Screwdriver Handle by Jasoncanning
...dle had to be hammered onto the bit holder. if the bit holder is too loose in the handle it will round out the hole very quickly.
thingiverse
free
Stackshot > MP-E65 Alignment Adaptor by Jasoncanning
...t to have the lens aligned with the stackshot rail otherwise stacked images may not stack correctly.
https://youtu.be/fvgnq14lop0
thingiverse
free
SD Card Holder for 3030 Extrusion by Jasoncanning
...pare piece of 1.75mm filament.
support is required on the body only for the clip, see image above to see where support is needed.
thingiverse
free
Spiralise Funnel with Air Channel by Jasoncanning
...aterial as it has excellent layer bonding and is very tough, while being flexible.
it can be scaled up or down using your slicer.
thingiverse
free
Glasses Case by Jasoncanning
...y stiff filament will work.
magnets required for the latch are 8mm diameter x 2mm thick, just glue them in with superglue.
enjoy!
thingiverse
free
8mm Rod - Storage End Caps by Jasoncanning
...are at 90 degrees from the cap, they will then come out easily.
filament used in the pictures is fillamentum vertigo galaxy pla.
thingiverse
free
Y Rod holder with clip by Jasoncanning
...stead for printing without supports.
after printing just make sure the clip fits tightly over the rod so it can not slide easily.
thingiverse
free
iRobot Roomba 800 & 900 series side brush by Jasoncanning
... centre hole as shown in the picture, but it is not essential, it just gives a cleaner finish and allows the screw to fit better.
thingiverse
free
Prusa i3 MK2/s LCD Knob with Bearing by Jasoncanning
...r if it is slightly loose you could use glue to hold it in place.
sorry about the poorly printed parts, this was the prototype :)
thingiverse
free
Ball jointed cable management for Prusa MK2S/Zaribo Extruder by Jasoncanning
...hreading the wires through the ball joints, do it in segments to make it easier then just joint the segments together afterwards.
thingiverse
free
Prusa i3 MK2 Filament Holder and optional Filament Guide by Jasoncanning
...ilament that is not on a reel. the keep stops it falling off the spool holder and works until the end of the filament is reached.
thingiverse
free
Ball jointed cable management for Prusa MK2S/Zaribo - X Motor by Jasoncanning
...hreading the wires through the ball joints, do it in segments to make it easier then just joint the segments together afterwards.
thingiverse
free
Ball jointed cable management for Prusa MK2S/Zaribo heated bed by Jasoncanning
...hreading the wires through the ball joints, do it in segments to make it easier then just joint the segments together afterwards.
thingiverse
free
Prusa I3 MK2 MK3 filament holder extended guide by CodeMachinist
... to where the mount is. this allows it to flex a little and act as a hook to keep the filament in place regardless of spool size.