28 Databeestje 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Parametric Phone Holder by databeestje
...metric phone holder by databeestje
thingiverse
should be easy to print and modify for various phone sizes with or without cases.
thingiverse
free
Generic configurable PCB mount by databeestje
... wanted something fancier then just the seperate tubes.
so i connected them up, and you can configure the sizes in the scad file.
thingiverse
free
Weather Proof cable box by databeestje
...or even fits. i have not printed it yet.
supposedly a rubber band should be wrapped around the face to make a water tight seal.
thingiverse
free
RC 17mm Hex wheel nut wrench by databeestje
... nut wrench by databeestje
thingiverse
i was in need of a 17mm hex wheel nut wrench for my new 1/8th scale.
a wrench was born!
thingiverse
free
Bolderkar by databeestje
...aal af, maar het werkt allemaal goed genoeg, en met 90cm lang kan deze precies overdwars, opgevouwen in de kofferbak van de auto.
thingiverse
free
Gutter drain leaf guard by databeestje
...hat needs better sizing for a side vent.
openscad, so relatively easy to adjust, although i didn't make anything variables :)
thingiverse
free
18650 holder configurable by databeestje
...e cells from there.
you can configure half open or not with a true/false. it only makes sense on the 2 by x configuration though.
thingiverse
free
Clip on desk cable guide by databeestje
... 1 of the desks whilst sliding the other way for routing wires. also made a single desk clip but have not tried that variant yet.
thingiverse
free
Mendel90 large Herringbone gear by databeestje
...90.
in the picture the original gear is left, the new one for the mendel90 is on the right, just forget that one in the middle.
thingiverse
free
Lithium Maintenance Charger by databeestje
..., depending on which way you want to mount the charger boards. a fan with duct might be a solution in the longitudinal direction.
thingiverse
free
30mm thick Fluorescent Clips by databeestje
...m led ring from aliexpress, it wasn't really a common item. it ended up just as expensive as a new fluorescent, which is odd.
thingiverse
free
RC body post ring with a clip retainer. by databeestje
...warm, fold the eye around and then let it harden.
thread the body clip through the retainer hole and you have a clip with ring.
thingiverse
free
FlySky FS-GT3B camera mount by databeestje
...n while drawing this. multiply this by 1000 in repetier host for the proper scale, then it slices. will upload a fixed stl later.
thingiverse
free
Ball Bearing Bushings for foldable cart by databeestje
....
print with brim or support if you need to. might just get away without either.https://youtu.be/nc92dfsftfw
pla 195c, 20% infill
thingiverse
free
Light blocker for EV-Box charge station by databeestje
...the inner diameter is 98, the outer 130, and a depth of 11.5.
also featured in this picture, the j1772 holder from thingiverse.
thingiverse
free
Mast mount for 48mm OD Aluminium pipe by databeestje
...able enough for car transport.
i just thought i'd upload those parts here instead of sticking them under the turbine thing.
thingiverse
free
Mitsubishi i-Miev speaker adapter ring by databeestje
...g to the door using the 3 plates behind it for fixation, the supplied screws with the speakers work fine, otherwise use m4 bolts.
thingiverse
free
PetPorte Smartflap anti draft plug by databeestje
...aller then i thought, probably better make it 12mm instead of 10mm to get a 24mm wide opening for the fingers. see the scad file.
thingiverse
free
Samsung Galaxy S6 with Bumper case car mount by databeestje
...g the case when using this mount.
the hole pattern is from some generic hama or halfords car mount. pictures will follow later.
thingiverse
free
LRP S10 Blast Slipper Axle and rear driveshaft bearing cover by databeestje
... on the front for the driveshaft should prevent rocks and dirt from getting close to the bearing where a lot of sand will end up.
thingiverse
free
Hose connectors 25mm for PP barrel by databeestje
...few hose connectors with a 25.4 mm diameter so that the hose fits snugly and i can secure it to the barrel with stainless screws.
thingiverse
free
Short RC body post extension by databeestje
...event the extension from breaking.
also added a few simple 6x16mm rings, although pla is probably too hard to cushion the flex.
thingiverse
free
HongNor SCRT10 chassis mud guards by databeestje
...icture. also get a shower cap so you can protect you electric equipment from the elements, it should be mostly winter proof then.
thingiverse
free
Sony Xperia T car mount by databeestje
...xplains the "awkward" positioning. i use the phone for dashcam recording whilst on the road, and this makes more sense.
thingiverse
free
OpenSCAD Parametric Pulleys with mount holes derivative from 16627 by databeestje
...ley is as easy as drawing a cylinder with the motor shaft diameter in the bottom or top, but i didn't actually code for that.
thingiverse
free
Bandvagn 206 track model by databeestje
...driving the sprockets with a dogbone. 2 drive motors for directional control, similar for 2nd carriage if that ever comes around.
thingiverse
free
Lenz2 helical turbine by databeestje
...hat is a issue with the stl importer for sketchup.
these stl files are hole free and should go through slic3r without warnings.
thingiverse
free
Lenz2 Helical Turbine XL by databeestje
... so far, the 1st attempt had pretty severe warping and i broke it off early on. hoping i can solve by just printing it on a raft.