26 626Pilot 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Planetary EZStruder Mount (geared stepper to EZStruder) by 626Pilot
...e the right screws to use with his, it's basically the same thing, so pick whichever one matches the screws you have on hand.
thingiverse
free
Rostock MAX 250mm Calibration Cylinder by 626Pilot
...bad delta rod length or printer radius setting in configuration.h) will have done so by 25cm in my experience.
slice as a vase.
thingiverse
free
Big & Tall Filament Holder Arm for Rostock MAX by 626Pilot
....update - 7-2-2014: rounded out the top edge of the arm, where it carries the spool. there should be less friction and noise now.
thingiverse
free
E3D Chimera/Cyclops mount for Rostock MAX by 626Pilot
...able management (removed one wire clip and took the tang out of the other), and added some stiffening strakes to the top surface.
thingiverse
free
Cable Clip for Trick Laser Rostock MAX METAL by 626Pilot
...e using unbrako #10-32 x 1/2 low-head caphead screws and 80/20 inc t-slot hw 10 series 10-32 roll-in t-nut w/ball spring #3922 n.
thingiverse
free
Rostock MAX Tower Alignment Clamps by 626Pilot
...jects are a higher priority for me right now, but if some people ask i'll set aside some time to finish the permanent clamps.
thingiverse
free
Smoothieboard 3/4/5X Mount for Rostock MAX by 626Pilot
...tabilize it while you do this. otherwise, you may shear off the top standoffs!
inspired by mhackney/eclecticangler's mount.
thingiverse
free
Endstop Z-Probe Mount for Rostock MAX/Orion/MAX Metal by 626Pilot
...itch to ensure that it always contacts the print surface when the end of the arm is lined up with those marks. this is important!
thingiverse
free
Ruby HallO Bed Leveling Probe by TheUnderDog
... tip and has only the magnet that came with the sensor due to the fact that its not permanent and it doesn't need to retract.
thingiverse
free
Azteeg X5 Mini Mount for Rostock MAX by 626Pilot
...#39;t have an account there, what the heck are you waiting for? it's hands down the best place to go for rostock max support.
thingiverse
free
Filament Spool Holder and Strain Relief Mast for Trick Laser MAX METAL by 626Pilot
...e using unbrako #10-32 x 1/2 low-head caphead screws and 80/20 inc t-slot hw 10 series 10-32 roll-in t-nut w/ball spring #3922 n.
thingiverse
free
LED Ring Snap Mount for Rostock MAX by 626Pilot
...nt the solder joints from working lose and failing over time. i recommend putting one of the zip ties close to the solder joints.
thingiverse
free
PanelDue Enclosure with Mount for Trick Laser Rostock MAX METAL by 626Pilot
...his is a remix of dc42's enclosure. it has a few new features, and the internal screw posts should print a little bit easier.
thingiverse
free
Cable Mast for Trick Laser Rostock MAX METAL by 626Pilot
...e using unbrako #10-32 x 1/2 low-head caphead screws and 80/20 inc t-slot hw 10 series 10-32 roll-in t-nut w/ball spring #3922 n.
thingiverse
free
Hall-Theta (Hall-O) Z-Probe Rostock MAX Mount by EskimoRuler
...unts for 626pilots hall-theta z-probe, but with 3 mounting holes that line up with the 3 main mounting holes for the rostock max.
thingiverse
free
Lucky 7 Blower Duct for E3D v6 Hot End (Rostock MAX / Orion) by 626Pilot
...g wood screws from mcmaster-carr.
.
one of the ducts is only a few millimeters from my heater block. there is no sign of melting.
thingiverse
free
Spacer for SSR mount for Trick Laser MAX Metal by 626Pilot
...inter is moved or jostled, and every now and then (at your discretion). you do not want your ssr to fall down inside the printer!
thingiverse
free
Counterweight System for Trick Laser Rostock MAX METAL by 626Pilot
...may fray even if that's not the case. it hasn't on my printer, but i can't promise it won't on anyone else's.
thingiverse
free
Dimensional Accuracy Calibration for Delta Printers by 626Pilot
... let me know whether or not this calibration system works for you, and whether you have any comments about how to make it better!
thingiverse
free
Low profile Rostock Max layer fan (E3D V6) by _jamesm
...(http://www.thingiverse.com/thing:137140). the normal layer fan will sit just a bit too low when using the 'tall' mount.
thingiverse
free
EZStruder Trick Laser Arm Mount for Rostock MAX/Orion/etc. by 626Pilot
... strictly up/down on the associated tower).
you can have three extruders (one per arm!) and still have room for another up top.
thingiverse
free
Hall-o Z-probe by daftscience
... magnetic arms it tends to stop the probe from retracting. i fixed this by placing another cube magnet behind the stationary one.
thingiverse
free
E3D versions 5 & 6 Bowden (groovemount) Hot End Mounting Plates for Rostock MAX & Orion by 626Pilot
...he time. hot wire it if you can. if you have the extruder heat turned on but the fan is turned off, the mounting plates may warp.
thingiverse
free
Hall-Theta (Hall-O) Z-Probe Bed Leveling Mount for Rostock MAX by 626Pilot
...just your filament flow to get these just right: enough pressure to keep it steady, but not enough to stop it from moving freely.
thingiverse
free
Delta Calibration for Rod Length by lstandage
...suring across the block from the side the tower number above the 50mm marking will indicate whether the rods need to be adjusted.
thingiverse
free
Rostock Max V2 Microswitch z-probe magnetic mount by jup2000
...
you will also need 6x 3/16" cube n48 magnets. i got mine on the cheap from amazon, but i've seen them on ebay as well.