Thingiverse
XT90 Power Bar by Zebble
by Thingiverse
Last crawled date: 3 years, 4 months ago
XT90 Power Distribution bar. Used for our 24V solar charging system at our flying field.
We used XT90-S sparkfree connectors as we were getting sparks at 24V with our previous banana plug distribution boxes.
Printed on ABS @ 25% infill. At least 2 outer layers so screws don't break walls when threaded.
Used 10AWG wire, but 8AWG or lower would be fine - adjust to your requirements.
Important to use wire with a silicone sleeve and leave the sleeve intact between connectors so it protects the print while soldering. I used a wire stripper to cut the silicon sleeve before and after the XT90 connectors, and then a slim wire cutter to cut between the two cuts and remove the sleeve. Lots of flux on the wire before soldering, and plenty of solder to create a positive electrical and mechanical connection.
Supports only required on the bottom, for the screw holes.
4 x M3x16 screws for end/input.
2 x M3x12 screws for bottom.
I used a bit of super glue on the top and bottom edge of each XT90 before quickly pushing it into the power bar. No need to glue the sides as there isn't enough contact on the sides.
When you install the End/Input, make sure the orientation is correct! The positive and negative should match the orientation of the 4 connectors on the top.
We used XT90-S sparkfree connectors as we were getting sparks at 24V with our previous banana plug distribution boxes.
Printed on ABS @ 25% infill. At least 2 outer layers so screws don't break walls when threaded.
Used 10AWG wire, but 8AWG or lower would be fine - adjust to your requirements.
Important to use wire with a silicone sleeve and leave the sleeve intact between connectors so it protects the print while soldering. I used a wire stripper to cut the silicon sleeve before and after the XT90 connectors, and then a slim wire cutter to cut between the two cuts and remove the sleeve. Lots of flux on the wire before soldering, and plenty of solder to create a positive electrical and mechanical connection.
Supports only required on the bottom, for the screw holes.
4 x M3x16 screws for end/input.
2 x M3x12 screws for bottom.
I used a bit of super glue on the top and bottom edge of each XT90 before quickly pushing it into the power bar. No need to glue the sides as there isn't enough contact on the sides.
When you install the End/Input, make sure the orientation is correct! The positive and negative should match the orientation of the 4 connectors on the top.
Similar models
thingiverse
free
Spade Connector Distribution Block by frankjay
...s version of the design but i'm confident it is the best one so far
i will have photos of the assembly steps uploaded shortly
grabcad
free
Terminal Connector with sleeve
...
this is brass terminal crimped with wire an added silicone sleeve terminal to protect connection between terminql and connector
thingiverse
free
Wago Power Bus Bracket - V13 by cheer4ftc
...n also use two of these back-to-back with intermediate wires bridging between the two sets to create an 8-input distribution bus.
thingiverse
free
Dyson charger plug shell by drors01
...shell by drors01 thingiverse dyson chargers for dc34 and similar models tend to develop bad connections near the end...
thingiverse
free
XT90 Panel Mount by georgebrooksuk
...ith male or female connectors. i have just printed with pla and superglued the xt90 in place once the wires have been soldered on
thingiverse
free
Ego Battery Adapter to XT60 by locnhinho
...solder. heat up the plate first add a blob of solder. then joint with the wire.
on the other end, solder to xt60 female connector
thingiverse
free
18650 holder 1S / 2S
...make sure they are correctly oriented. 1s instructions follow similar steps as described in the2s construction, however: solder two...
thingiverse
free
AA Battery Blank by CrispyDragon
...in each end, and solder a wire between the screws.
sand or file the ends of the screws to make it easier for the solder to stick.
thingiverse
free
Huxley power wire cover with switch by Inquisitor
...ingiverse
this is a cover for the soldered ends of the power input for a reprap huxley. it includes a hole for an on/off switch.
thingiverse
free
5S to 9v Voltage Reducer for FatShark Goggles by kah00na
... didn't take any pictures of it while i was assembling it... my bad. i'll make another eventually and add more pictures.
Zebble
thingiverse
free
GoPro3 Case for CrossFire Multicopter by Zebble
...gopro3 case for crossfire multicopter by zebble
thingiverse
very simple gopro3 case for crossfire multicopter.
thingiverse
free
Solder Spool Stand - 2 sizes by Zebble
...by zebble
thingiverse
remixed with sketchup. skp included.
2 stands now available - added larger stand for larger solder spool.
thingiverse
free
H-quad micro quadcopter landing gear by Zebble
...h-quad micro quadcopter landing gear by zebble
thingiverse
simple landing gear for ukarmy04's h-quad micro quadcopter.
thingiverse
free
Micro H-Quadcopter remix for smaller build platforms by Zebble
...rmy04's micro h-quad frame.
frame was split in half into two symmetrical pieces with the addition of keyed slide-in supports.
thingiverse
free
RCTimer Telemetry and CN06 GPS Holder by Zebble
...ot to interfere mechanically with the antenna in various mounting positions.
snug fit of both the gps and telemetry once glued.
thingiverse
free
Solder Spool Stand Improved by AndrewBCN
...a complete redesign of the solder spool stand by zebble (wade weppler), which is itself a remix of the...
Xt90
turbosquid
$3
xt90 connector male female set
... connector male female set for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1672898)
turbosquid
$3
XT90-S connector male female set
... connector male female set for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1673998)
turbosquid
$3
XT90-H connector male female set
... connector male female set for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1673979)
thingiverse
free
XT90 Holder by saschahelle
...xt90 holder by saschahelle
thingiverse
xt90 holder
thingiverse
free
Panel XT90 by Leon8121
...panel xt90 by leon8121
thingiverse
to hold your xt90 on your enclosure
thingiverse
free
XT90 holder for soldering
...xt90 holder for soldering
thingiverse
xt90 holder to make it easier to solder them, both male and female sides.
thingiverse
free
XT90 Cap by DanHanson
...xt90 cap by danhanson
thingiverse
this xt90 cap fits well and only uses .3 meters of 1.75mm filament.
thingiverse
free
XT90 XT60 HOLDER by jean5
...xt90 xt60 holder by jean5
thingiverse
xt90 xt60 holder
thingiverse
free
xt90 Plate - 2 fuse holders 2 XT90 female for power output by georgebrooksuk
...ingiverse
xt90 power output plate.
2 fuse holder hole, 2 slots for xt90 female connectors. superglue the xt90s in to secure them
thingiverse
free
XT90 Panel Mount by georgebrooksuk
...ith male or female connectors. i have just printed with pla and superglued the xt90 in place once the wires have been soldered on
Bar
archibase_planet
free
Bar
...bar
archibase planet
bar bar rack
bar 2 - 3d model for interior 3d visualization.
archibase_planet
free
Bars
...bars
archibase planet
horizontal bar parallel bars
parallel bars - 3d model for interior 3d visualization.
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
3d_export
$10
bar
...bar
3dexport
modern bar
Power
turbosquid
$100
power
...ower
turbosquid
royalty free 3d model power for download as on turbosquid: 3d models for games, architecture, videos. (1421990)
3d_export
$5
Power
...power
3dexport
3d_export
$5
power outlets
...power outlets
3dexport
power outlets
3ddd
$1
lion power
...lion power
3ddd
лев , статуя
lion power gold sculpture
3ddd
$1
Sea Power
...
компас , море , часы
часы с компасом sea power
3ddd
free
Meridiani / Power
...power
3ddd
meridiani , круглый
стол power производитель meridiani, диаметр 120,высота 67
3d_export
$5
Power Surge
...power surge
3dexport
the power surge is a all mesh carnival ride to lower in game part count and lag
turbosquid
$8
Airport Ground Power Unit (AXA Power )
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$50
Power Houser
...rbosquid
royalty free 3d model power houser for download as on turbosquid: 3d models for games, architecture, videos. (1333800)
3d_export
$5
power outlet
...power outlet
3dexport
power outlet<br>format file maya 2018, 3d max 2017, obj, fbx