Thingiverse
X axis end clamp by bunjatec
by Thingiverse
Last crawled date: 3 years ago
this clamps onto the end of the x axis to stop the rods pushing through allowing the belt to be tensioned.
requires 2x M3 nuts and bolts, the nut is retained in the Hex socket on the fixing
you will need to print :
1x end clamp
2x end clamp fixings
The clamp then holds the ends of the x stage rods and stops them poking out.
requires 2x M3 nuts and bolts, the nut is retained in the Hex socket on the fixing
you will need to print :
1x end clamp
2x end clamp fixings
The clamp then holds the ends of the x stage rods and stops them poking out.
Similar models
thingiverse
free
Adjustable Z End Stop for Prusa Mendel by Stroodies
...tment of the z end stop position.
hardware:
(6x) 3m nuts
(1x) 3m x 35mm bolt
(2x) 3m x 20mm bolt
(2x) 2m x 18mm bolt
(2x) 2m nuts
thingiverse
free
Clamp for X-axis rods on I3/P3 printer by Peter_I
...ter-center distance for rods is 46mm.
"anything" could be sensors for end-stops, magnets or jolly blinking led's.
thingiverse
free
12mm rig clamp by GrimbiXcode
...ode
thingiverse
12mm rod clamp
things you need for
2x m4 30mm screw hex (with nut head)
2x m4 nut
2x 12mm rods you want to clamp
thingiverse
free
HyperCube XY_Joiner_8mm_Alu_Rods Stronger by Pogasi
... 2x m3x35
and for clamp 4x m3x25
and 6x m3 selflocking nut.
thingiverse
free
MakerBot EndStop Support For Workbee/OX CNC by Patrickl91
...whole things :
2x m5x8 hex screw
2x m5 lockable nuts
edit 2018_06_11 - adding specific support for x axis. + update sketchup file
thingiverse
free
Prusa 50mm Spacing 8mm Rod X Axis Bar Clamp by wildBill83
...bars down so the belt can be tightend without damaging the x ends. print two and use one between carriage and x end on each side.
thingiverse
free
LowRider2 - z end stop by TheMaxx2804
...gn to clamp it on the rod with the possibility to fix and adjust it in the height if needed.
this is for the 25mm metric version.
thingiverse
free
Strap Clamp by RDX_x
...u need
4x strap clamp corner
2x strap clamp expander
10cm m5 rod
2x m5 nuts
2-4x big washers
1x strap 28x1,5mm x x meters length
thingiverse
free
X Axis End Stop Holder by plamari
...ned and hence moved easily when required, but not when bumped.
not sure if it is suitable for anything other than opto end stops.
thingiverse
free
Prusa i3 Zonestar P802M x axis steel rod clamp by Ahli
...se
this is for the end of the x axis to hold the steel rods in place.
be carful this is my first thing :)
greetings from germany
Bunjatec
thingiverse
free
Quadro spnner by bunjatec
...ne.
i'd recommend a thick wall with medium infill, making the area around the end of the tool solid. but hollow in the handle
thingiverse
free
solder holder by bunjatec
...t
bar prints upside down.
printed pla on glass with heated bed.
no supports, no finishing, ready to use straight off the printer.
thingiverse
free
prusa i3 Zonestar p802 Melzi 80mm fan holder and duct by bunjatec
...80mm fan holder and duct by bunjatec
thingiverse
80mm fan holder and duct for melzi pcb as comes with the prusa i3 zonestar p802
thingiverse
free
prusa i3 Zonestar p802 z leveing tool by bunjatec
...ss that could cause warping and gives a very straight part.(which is handy if you want to use it to calibrate/setup your printer)
thingiverse
free
prusa i3 Zonestar p802/Anet A8 mounting blocks by bunjatec
...o attach to a 18mm mdf sheet.
makes it much more dimensionally stable
as with any of my objects if you need cad file let me know.
thingiverse
free
prusa i3 Zonestar p802 filamnet feed clip by bunjatec
...7.7mm i think) i put a 3mm screw hole to tighten it, but it worked fine without.
prints without supports with the clip feature up
thingiverse
free
prusa i3 Zonestar p802 40mm fan cover and endstop by bunjatec
...ne that's 2mm thinner) and did a few other mods and cut away the can cover section, the old fan grille then fits on top fine.
thingiverse
free
prusa i3 Zonestar P802N P802NA Y idler by namelessexile
...prusa i3 zonestar p802n p802na infill 20% create by bunjatec edit for p802n by...
thingiverse
free
Tronxy X5SA tripple leadscrew upgrade by bunjatec
...en side plate it should be eliminated it's also a little low requiring the belt pulley to be mounted quite high on the shaft.
Clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp
thingiverse
free
Clamp
...clamp
thingiverse
clamp for vacform
thingiverse
free
Clamp by bexer
...clamp by bexer
thingiverse
clamp, one clamp for many possibilities!
thingiverse
free
clamp by kimduckkyo
...clamp by kimduckkyo
thingiverse
clamp
thingiverse
free
clamp by glukofinder
...clamp by glukofinder
thingiverse
clamp
thingiverse
free
Clamp Chain
...clamp chain
thingiverse
this is a clamp
thingiverse
free
Clamp by wslab
...clamp by wslab
thingiverse
clamp
thingiverse
free
CLAMP by leonk
...clamp by leonk
thingiverse
clamp
thingiverse
free
Clamp by jkorinek87
...clamp by jkorinek87
thingiverse
clamp
thingiverse
free
Clamp by Emmanuelgnanasekar
...clamp by emmanuelgnanasekar
thingiverse
this thing is a clamp model , it can be used for soft clamping things
Axis
thingiverse
free
Axis
...axis
thingiverse
had no dowels laying around so modeled an axis in 360
thingiverse
free
Axis
...axis
thingiverse
an right handed cartesian axis. notches indicate positive rotation direction.
thingiverse
free
CR10S X-axis & Y-axis spacer
...cr10s x-axis & y-axis spacer
thingiverse
4mm spacer for x-axis & y-axis on the cr10s.
thingiverse
free
AXYS KEYCHAIN
...axys keychain
thingiverse
polaris axys platform keychain
thingiverse
free
for Axis by bassemwagih
...for axis by bassemwagih
thingiverse
axis diameter = 1.3 cm
thingiverse
free
Axis Tree - 3 and 5 Axis by zefram
...and 5 axis by zefram
thingiverse
flexible 3 and 5 axis tree signpost to demonstrate or remind the axes on a 3 or 5 axis machine.
thingiverse
free
Linear Axis by wizard23
...linear axis by wizard23
thingiverse
a linear axis i wanted to test.
thingiverse
free
2 adjustable axis (Y-Z Axis) by NerdCorner
... (y-z axis) by nerdcorner
thingiverse
detailed explanation in my blogpost: https://nerd-corner.com/2-adjustable-axis-cad-design/
thingiverse
free
z axis motor holder for metal x axis to go from prusa I2 x axis to I3 x axis by brunoschoofs
...al x axis from aliexpress
that is like a prusa i3 x-axis to fit on your prusa i2
the bottom holder are comming to patience please
thingiverse
free
Z axis regulation
...z axis regulation
thingiverse
z axis regulation without synchronization, for artillery
End
thingiverse
free
32mm end cap ball end
...32mm end cap ball end
thingiverse
modified my previous design to have rounded cap ending.
thingiverse
free
Preonic End
...preonic end
thingiverse
end piece for the rev 2 preonic
thingiverse
free
vacuum end shop vac end by luiscollie
...verse
shop vac end with tight end for more suction....this fits standard shop vac end about 58 mm id.. easy to print standing up
thingiverse
free
end mill tray for 6 end mills by jeffcarlsbad
...end mill tray for 6 end mills by jeffcarlsbad
thingiverse
end mill tray for 6 end mills
thingiverse
free
end mill tray for 4 end mills by jeffcarlsbad
...end mill tray for 4 end mills by jeffcarlsbad
thingiverse
end mill tray for 4 end mills
thingiverse
free
Maze's End
...maze's end
thingiverse
this a fan work of the maze's end from magic: the gathering
thingiverse
free
Heim Rod End / End Stangen Gelenk by MBWolf
...heim rod end / end stangen gelenk by mbwolf
thingiverse
standard heim rod end / einfaches endstangengelenk
thingiverse
free
THE END IS NEAR Stencil
...the end is near stencil
thingiverse
the end is near
thingiverse
free
End stop by Ha3d
...end stop by ha3d
thingiverse
end stop
thingiverse
free
Book end by henrykaplan
...book end by henrykaplan
thingiverse
this is a book end.