Thingiverse
WLED Powered Puck / Accent Light by mrspiffy
by Thingiverse
Last crawled date: 2 years, 9 months ago
Based on my previous WLED powered LED night light (https://www.thingiverse.com/thing:4816082), I shrunk the form factor to create a 1" x 2.5" puck light that can be stashed anywhere you need an accent light. This light is compatible with Home Assistant and the shades found on my night light page.
Build Instructions
Three simple parts to print, the puck base needs to be printed on a raft with support. The other parts can be printed normally. A little bit of hot glue secures the LED Ring to the base and once you've fed the wires through, put a spot of glue in the hole to secure them there.
The resistor that I used for the LED ring is 330 ohms.
Flip the base over and solder your leads to the Wemos D1 using the circuit diagram provided. Make sure that the processor faces down when you do this. Once wired up, slip the D1 into the processor plate. A dab of hot glue will help secure the D1 in the plate. Now line up the notches and snap the processor plate into the puck base and the puck shade over the LED's and you're done.
Programming
You can either program it with ESPHome or with WLED. Either way is compatible with Home Assistant.
I went the WLED route and there are several ways to do this listed here: https://github.com/Aircoookie/WLED/wiki/Install-WLED-binary.
The binary you will need is the WLED_x.x.x_ESP8266.bin for Wemos D1 mini, the processor used here.
Pro Tip: make sure you have a good USB data cable. There are a lot of crap cables out there.
BOM
These are affiliate links which help fund future projects here:
Wemos D1 mini: https://www.amazon.com/dp/B081PX9YFV?psc=1&linkCode=sl1&tag=ani101mantoo-20&linkId=e1666c58e99e05798235fd2858bc1942&language=en_US&ref_=as_li_ss_tl
12 LED Ring: https://www.amazon.com/dp/B081PX9YFV?psc=1&linkCode=sl1&tag=ani101mantoo-20&linkId=e1666c58e99e05798235fd2858bc1942&language=en_US&ref_=as_li_ss_tl
1 330 ohm resistor
some shrink tubing and hot glue
Build Instructions
Three simple parts to print, the puck base needs to be printed on a raft with support. The other parts can be printed normally. A little bit of hot glue secures the LED Ring to the base and once you've fed the wires through, put a spot of glue in the hole to secure them there.
The resistor that I used for the LED ring is 330 ohms.
Flip the base over and solder your leads to the Wemos D1 using the circuit diagram provided. Make sure that the processor faces down when you do this. Once wired up, slip the D1 into the processor plate. A dab of hot glue will help secure the D1 in the plate. Now line up the notches and snap the processor plate into the puck base and the puck shade over the LED's and you're done.
Programming
You can either program it with ESPHome or with WLED. Either way is compatible with Home Assistant.
I went the WLED route and there are several ways to do this listed here: https://github.com/Aircoookie/WLED/wiki/Install-WLED-binary.
The binary you will need is the WLED_x.x.x_ESP8266.bin for Wemos D1 mini, the processor used here.
Pro Tip: make sure you have a good USB data cable. There are a lot of crap cables out there.
BOM
These are affiliate links which help fund future projects here:
Wemos D1 mini: https://www.amazon.com/dp/B081PX9YFV?psc=1&linkCode=sl1&tag=ani101mantoo-20&linkId=e1666c58e99e05798235fd2858bc1942&language=en_US&ref_=as_li_ss_tl
12 LED Ring: https://www.amazon.com/dp/B081PX9YFV?psc=1&linkCode=sl1&tag=ani101mantoo-20&linkId=e1666c58e99e05798235fd2858bc1942&language=en_US&ref_=as_li_ss_tl
1 330 ohm resistor
some shrink tubing and hot glue
Similar models
thingiverse
free
Prusa Light Bar Simple Print by wbushee
...c=1&linkcode=sl1&tag=bluemonkeydev-20&linkid=4c12befa75c811732eb310b986c3f297&language=en_us&ref_=as_li_ss_tl
thingiverse
free
Simple WLED Powered Night Light by mrspiffy
...lithopane shade?
a larger 16 pixel ring can be used if the stump that centers the ring is widened.
post your makes and remakes!
thingiverse
free
RGB Youtube Play Button by KenMakesMistakes
...c=1&linkcode=sl1&tag=kenmakesmista-20&linkid=f2678d6d510fe6336c34cc36e0e6d247&language=en_us&ref_=as_li_ss_tl
thingiverse
free
Onefinity Monitor Arm Connector by cyberreefguru
...g=cyberreefgu0c-20&linkid=14415004f4b141eaae9525187bb68eb3&language=en_us&ref_=as_li_ss_tl (for 7" monitor only)
thingiverse
free
Spacecat - Launch pad v2 Case by jneubeck
...amp;psc=1&linkcode=sl1&tag=neubeck-20&linkid=5c1adcf1e26e86d2a2323754efe7a0b7&language=en_us&ref_=as_li_ss_tl
thingiverse
free
Seed organizer by reeseallen
...&psc=1&linkcode=sl1&tag=reeall-20&linkid=cfd0b80d7ba1f7ea99e5eb21ed0fb88f&language=en_us&ref_=as_li_ss_tl
thingiverse
free
Foam Core Spray Paint Booth by BenE
...p;sr=8-1&linkcode=sl1&tag=beneadie-20&linkid=e738a5d873a60e3d7ac15b0a6311327a&language=en_us&ref_=as_li_ss_tl
thingiverse
free
Batbox V1 by Nath042
...ode=sl1&tag=nath0420a-21&linkid=5c1eb5f14c82d8cef6cfb9bb1c3d425a&language=en_gb&ref_=as_li_ss_tl - battery holder
thingiverse
free
Engel Fridge Digital Temperature Controller by 2manytoyz
...ytoyz-20&linkid=0dcb3de269cda7d1567383449e50a585&language=en_us
as an amazon associate i earn from qualifying purchases.
thingiverse
free
Nightlight Bracket by ratranch
...7ddf82cd05992b55d8d644fc&language=en_us), allowing you to attach a custom cover. print on its side with build plate supports.
Mrspiffy
thingiverse
free
Laptop stand for larger laptops by mrspiffy
...laptop stand for larger laptops by mrspiffy
thingiverse
laptop stand for larger laptops. about 10 degree slope.
thingiverse
free
Shower curtain hanger by mrspiffy
...nting shower curtain hanger. fits up to 40mm rod. you can lay up four at a time on a 200x200 bed. print at 50% fill for strength.
thingiverse
free
Generic Coin Bank Plug by mrspiffy
...st the plug to a figure coin bank, so we printed a replacement. resize as necessary, should work for a variety of figural banks.
thingiverse
free
Pole Hook by mrspiffy
...erse.com/thing:1069028.
this has been sized to work with a 3/4" pole, you can easily scale this up or down to fit your pole.
thingiverse
free
Remixed Wanhao iiip filament guide by mrspiffy
...ixed filament guide for wanhao/iiip printers. this remix centers the filament on the spool and now has a slot for easy threading.
thingiverse
free
20 degree camera tilt base by mrspiffy
...lt base by mrspiffy
thingiverse
super simple 20 degree base for webcams with 4 inch round base. can be resized for 3 inch bases.
thingiverse
free
Remixed Shower Hook by mrspiffy
...crubbers, etc.
for heaver items like full sized towels, i recommend this hook instead: https://www.thingiverse.com/thing:4635388
thingiverse
free
Hand Hook by mrspiffy
... at 60% to get a size that would work with our pan lids. depending on how heavy your object to hang is, you should increase fill.
thingiverse
free
Carpet Corner Stiffener by mrspiffy
...hex fill for stiffness.
grooved side up. put your tape on the side without grooves and stick that to the underside of the carpet.
thingiverse
free
Tooth Brush Holder for Oral B CrossAction by mrspiffy
...ssaction line of electric toothbrushes. the top opening is 25mm across, so if your tooth brush is less than that, this will work.
Wled
thingiverse
free
WLED NodeMCU Case
...se
thingiverse
wled box for nodemcu to use with wled firmware to control ws2812b rgb ledshttps://github.com/aircoookie/wled/wiki
thingiverse
free
WLED ESP32 by Ulmerspatz
...wled esp32 by ulmerspatz
thingiverse
gehäuse für einen azdelivery esp32 zum bau eines wled controller.
r=470
c= 1000 µf/10v
thingiverse
free
WLED Nodemcu Box by Fabiolol
...wled nodemcu box by fabiolol
thingiverse
simple box to install nodemcu to control my ledstrips with amazing wled software.
thingiverse
free
WLED wemos shield box v1.0 by serg74
...wled wemos shield box v1.0 by serg74
thingiverse
wemos shield box for wled project
thingiverse
free
WLED shield box v1.5 by serg74
...wled shield box v1.5 by serg74
thingiverse
wled shield box v1.5. ir glass part have to printed from transparent material.
thingiverse
free
WLED case (ESP-01)
...led strip with button (on/off or change mode)
hardware: esp-01s (with 1mb spi flash)
firmware: https://github.com/aircoookie/wled
thingiverse
free
Wave lamp remix (WLED) by sliekas
... board (firmware for board is wled - https://github.com/aircoookie/wled)
addressable led strip (ws2812b 60leds/m), width - 10mm
thingiverse
free
WLED Box for ESP8266 Board by dapostol73
...d by dapostol73
thingiverse
quick little box i build for housing my wled esp8266 board behind my tv for my hyperion project leds
thingiverse
free
YEAH LED LAMP WS2812 36cm Stripe WLED
...812 36cm stripe wled
thingiverse
a shortened version of the lamp.
had a 36cm stripe laying around.
recommending aircookies wled
thingiverse
free
WLED shield box v1.5 with display by blazoncek
...wled shield box v1.5 with display by blazoncek
thingiverse
Puck
3d_ocean
$1
Hockey Puck
...sports
design hockey puck that can be used in articles and advertisements, magazines for sports games and everything to the time.
turbosquid
$10
Hockey Puck
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Hockey Puck
...model hockey puck for download as png, 3ds, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1356266)
turbosquid
free
Hockey Puck
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Hockey puck 3D Model
...hockey puck 3d model
3dexport
hockey puck spacer washer disk shim
hockey puck 3d model gizmo_fbi 28754 3dexport
3ddd
$1
Pouf Ijack Shuffle Puck
...pouf ijack shuffle puck
3ddd
пуф
pouf ijack shuffle puck
turbosquid
$10
Camerich Puck Ottoman
...model camerich puck ottoman for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1442488)
3d_export
$19
Hockey Stick Puck 3D Model
...play nhl sport winter equipment collection photorealistic detailed materials
hockey stick puck 3d model humster3d 69672 3dexport
humster3d
$15
3D model of Hockey Stick & Puck
...iled 3d model of hockey stick & puck in various file formats. all our 3d models were created maximally close to the original.
3d_export
$5
Hockey Puck
...ormats. preview images are rendered in cycles render.<br>i am happy to answer any questions you might have about the model.
Accent
3ddd
free
Contemporary Accent Chair
...contemporary accent chair
3ddd
accent
contemporary accent chairs with chrome base, set of 2, gray
3d_export
$5
Koi Wall Accent
...koi wall accent
3dexport
koi wall accent for decoration
3ddd
$1
Accent Mirrors
...accent mirrors
3ddd
зеркала
turbosquid
$45
accent chair
...squid
royalty free 3d model accent chair for download as 3ds on turbosquid: 3d models for games, architecture, videos. (1688654)
3d_export
$5
Dog wall accent
...dog wall accent
3dexport
dog silhoutte wall accent wood
turbosquid
$17
Accent Mirrors
...alty free 3d model accent mirrors for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1200829)
turbosquid
$20
Accent Chairs
...free 3d model accent chairs for download as max, max, and obj on turbosquid: 3d models for games, architecture, videos. (1636981)
turbosquid
$6
PASCAL ACCENT
...free 3d model pascal accent for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1216700)
turbosquid
$15
Westie Accent Chair and Westie Accent Ottoman - Gray
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
Accente Chandelier
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Powered
turbosquid
$100
power
...ower
turbosquid
royalty free 3d model power for download as on turbosquid: 3d models for games, architecture, videos. (1421990)
3d_export
$5
Power
...power
3dexport
3d_export
$5
power outlets
...power outlets
3dexport
power outlets
3ddd
$1
lion power
...lion power
3ddd
лев , статуя
lion power gold sculpture
3ddd
$1
Sea Power
...
компас , море , часы
часы с компасом sea power
3ddd
free
Meridiani / Power
...power
3ddd
meridiani , круглый
стол power производитель meridiani, диаметр 120,высота 67
3d_export
$5
Power Surge
...power surge
3dexport
the power surge is a all mesh carnival ride to lower in game part count and lag
turbosquid
$8
Airport Ground Power Unit (AXA Power )
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$50
Power Houser
...rbosquid
royalty free 3d model power houser for download as on turbosquid: 3d models for games, architecture, videos. (1333800)
3d_export
$5
power outlet
...power outlet
3dexport
power outlet<br>format file maya 2018, 3d max 2017, obj, fbx
Light
archibase_planet
free
Light
...light
archibase planet
lamp lighting light
light - s2 - 3d model for interior 3d visualization.
archibase_planet
free
Light
...light
archibase planet
light luminaire lighting
light l0465 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
lighting
...lighting
3dexport
lighting
3d_export
$5
lighting
...lighting
3dexport
lighting in livingroom
turbosquid
$3
Lighting Tree with Lights
...d model lighting tree with lights for download as max and 3ds on turbosquid: 3d models for games, architecture, videos. (1585507)
archibase_planet
free
Light
...light
archibase planet
luster lighting solution
light - s - 3d model for interior 3d visualization.
archibase_planet
free
Light
...light
archibase planet
luster lamp lighting
light 1 - 3d model for interior 3d visualization.
archibase_planet
free
Lights
...lights
archibase planet
surgical lights surgical lamp
surgical lights (floor) - 3d model for interior 3d visualization.
archibase_planet
free
Light
...light
archibase planet
lighting luminaire candlelight
light l0463 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$18
street light-lighting-light-xia bing
...
3dexport
street light-lighting-light-xia bing<br>max 2015 v-ray 3 max 2015<br>textures<br>all files in zip...