Thingiverse
Wanhao D9 bed spacer by Sidewayswizzard
by Thingiverse
Last crawled date: 3 years ago
The cap screws that hold the rollers under the bed were rubbing on the frame behind the main box and the deck was rubbing on the rear stop switch. I also noted that the screws holding the rollers under the bed were cantered when properly tensioned. The flanged end of the spacers give a little more support under the bed which has solved the issue of the wheels being cantered. The spacers are 2mm taller so you need to ditch the spring washers to keep the screw length, it was a must in my case as like I mentioned the head of the screw was rubbing on the frame. Ditching the spring washer gave it clearance and the extra bed height stopped it hitting the rear switch
Similar models
thingiverse
free
Spring Guide Remix by dpears
...n raising the z-axis stop switch to the upper set of holes in order to combat the added z-height of the spring guides and washer.
thingiverse
free
Replicator Heated Build Platform Washer/Spacer Replacements by mechamithrandir
...echamithrandir
thingiverse
instead of using washers or spacers to hold up the springs on the replicator. i used printed spacers.
thingiverse
free
Hotbed clip and washer by ksevin
...in place.
the washers avoid the tearing of the electrical circuit under the hotbed. i strongly recommend the use of the washers.
thingiverse
free
PRINTinZ Z-axis End Stop Spacer for QIDI Tech I by mWagner84
... i which allows the print bed to accommodate a printinz bed plate. it clips into the bed frame and wraps around the drive screw.
thingiverse
free
Prusa i3 Migbot Z Axis stop switch spacer by DarkShadowX5
... away from the wires. comes with a nut holder for easy adjustments.
i printed it with 0.2 layer height, 100% infill for strength.
thingiverse
free
End stop - Limit switch Holder (Tevo Tarantula) V2 by ErratikMantis
...ly generic part.
the part that holds the screw is spaced from the wheel bearing by a spring washer. the hole is for an m3 screw.
thingiverse
free
120mm Spacer by ls7corvete
... there is no hole for screws, just a bump to hold things in place.
not much left of the original file, but i included it anyways.
thingiverse
free
8mm hotbed spring washers with insulation support by red6rick
..., and hold up a 4mm cork sheet under the bed for insulation. overall, this cuts my heat-up time in half with virtually no effort.
thingiverse
free
Ender 3 and Ender 5 bed leveling spring spacer with capture nut
... the spacers and then put the bed back on your carriage and put on the bed leveling wheels. you will now have a much stiffer bed.
cults
free
Bed, Roller, Stop
...ay down on it . . this stops it from wandering around i have rollers under the bed about 2 inches across ad 2 inches in diameter
Sidewayswizzard
thingiverse
free
Lego bogie by Sidewayswizzard
...0mm long. holes in the wheels are slightly undersized for a slight press fit on the axle, you may need to ream the hole slightly.
thingiverse
free
Magazine coupler for 10rnd mags by Sidewayswizzard
...e a little hot glue to keep the mags in place, printing at 99% scale might get a press fit. check your local laws before printing
thingiverse
free
Lego Bogie by Sidewayswizzard
...makes an easy to obtain axle. superglue one side onto the main bogie, put the assembled axles in and then glue the other side on.
D9
3d_export
$12
industrial desk lamp d9
... real object. 3. lights and cameras are included in the scenes renders using vray * renders are made in 3ds max 2018 using vray 5
3ddd
free
Ceramica Bardelli (Fornasettiana)
...плитки: bianco extra, l.111, c&c; a1, c&c; a9, c&c; d9 c&c; d3, nero...
thingiverse
free
splitter d9 by jkiki
...splitter d9 by jkiki
thingiverse
thingiverse
free
D9 Hotend Blower by RidHS
...d9 hotend blower by ridhs
thingiverse
modified d9 hotend blower to provide more direct nozzle cooling
thingiverse
free
D9 Dozer with Bar Armor by ThudOne
...d9 dozer with bar armor by thudone
thingiverse
d9 dozer with bar armor ho scale.
israeli and us army version.
thingiverse
free
Wanhao D9 Cable relief for MK10 by OZ9HMN
...wanhao d9 cable relief for mk10 by oz9hmn
thingiverse
wanhao d9 cable relief for mk10
thingiverse
free
Rocket model. Engine D6 or D9. by qlrs
...rocket model. engine d6 or d9. by qlrs
thingiverse
rocket model. engine d6 or d9.
thingiverse
free
RS232 / SUB-D9 box by vidiq
...as to create a female-to-female crossing adapter for fluke-45. the design is tuned for my printer with 0.4 nozzle and 0.2 height.
thingiverse
free
WANHAO DUPLICATOR D9 300 Bed Levelling knob by bubu1882
...wanhao duplicator d9 300 bed levelling knob by bubu1882
thingiverse
wanhao duplicator d9 300 bed levelling knob
thingiverse
free
WANHAO DUPLICATOR D9 400 Bed Levelling knob by bubu1882
...wanhao duplicator d9 400 bed levelling knob by bubu1882
thingiverse
wanhao duplicator d9 400 bed levelling knob
Wanhao
thingiverse
free
Wanhao Logo Plate / Wanhao Logo Schild by JMDesigns
...wanhao logo plate / wanhao logo schild by jmdesigns
thingiverse
wanhao logo plate / wanhao logo schild
thingiverse
free
Wanhao logo by nebtio
...wanhao logo by nebtio
thingiverse
wanhao logo
thingiverse
free
Wanhao keychain by Rein3003
...wanhao keychain by rein3003
thingiverse
a keychain with the logo of wanhao
thingiverse
free
Wanhao Di3 v2 Light / Wanhao Di3 v2 Beleuchtung by JMDesigns
...wanhao di3 v2 light / wanhao di3 v2 beleuchtung by jmdesigns
thingiverse
wanhao di3 v2 light / wanhao di3 v2 beleuchtung
thingiverse
free
TUSH For Wanhao by wtmi1992
...tush for wanhao by wtmi1992
thingiverse
the ultimate spool holder, modified for the top of the wanhao control box. fits snug.
thingiverse
free
fanduct wanhao d12 by theopoilmek
...fanduct wanhao d12 by theopoilmek
thingiverse
fanduct pour wanhao d12
thingiverse
free
Wanhao i3 Marlin by johan21
...wanhao i3 marlin by johan21
thingiverse
marlin for wanhao i3 rampsboard 1.4.
thingiverse
free
Wanhao Duplicator i3 by imagineering4
...wanhao duplicator i3 by imagineering4
thingiverse
these are the stl files for the improvements to the wanhao duplicator i3, v2
thingiverse
free
Wanhao D6 filament guard
...wanhao d6 filament guard
thingiverse
this is a filament guard for wanhao d6 machine to avoid the filament unrolling
thingiverse
free
Wanhao Duplicator i3 Model by Hilde3D
...wanhao duplicator i3 model by hilde3d
thingiverse
wanhao duplicator i3 model
Spacer
turbosquid
$55
Spacer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$60
grendizer & double spacer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Hex Spacers M3 Male-Female
... spacers m3 male-female
3dexport
hex spacers m3 male-female with length from 5mm to 60mm for printed circuit boards. step files.
3d_export
$5
industrial lift - spacer crane
...crane<br>- 500 kg<br>- render 3ds max 2020 and corona renderer.<br>- formats: max 2020, max 2017, obj, fbx, stp
3d_export
$5
spacer hanging light
...lampshades: any total number of lamps: 6 polys: 18 546 verts: 19 045 https://imperiumloft.ru/lyustry-175/ev_a048924-eurosvet.html
turbosquid
$5
Industrial lift Spacer crane Renaissance construction
...naissance construction for download as max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1571898)
3d_export
$7
industrial lift - spacer crane renaissance construction
...ction<br>- 750 kg<br>- render 3ds max 2020 and corona renderer.<br>- formats: max 2020, max 2017, obj, fbx, stp
3d_export
$10
Spacer Sliding Wardrobe 1200 Hanger
...painter available for all software<br>ue4. ue5. blender. maya. 3d max. unity. c4d.<br>formats: .obj .gltf .fbx .blend
3d_export
$5
Hockey puck 3D Model
...hockey puck 3d model 3dexport hockey puck spacer washer disk shim hockey puck 3d model gizmo_fbi 28754...
3d_export
$5
Front 30mm Lift Kit for 1996-2004 Nissan Pathfinder and 1997-2003 Infiniti QX4
...terrano r50, regulus 1997-2003 infiniti qx4 - front strut spacer ...
Bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
Bed
...bed
3ddd
bed , постельное белье , постель
bed
3d_export
$7
bed adairs bed
...rs bed
3dexport
bed adairs bed in modern style. if you want a smoother surface, please turn on turbosmooth in the modifier list.