VoronoiBowl1 by bbinnard

...;5 lines constructed 2.00 mm>printed 2.01 mm>_5 lines i think that's useful information when designing technical parts.

...ader set of ready to print classic engagement rings sizes: 15 mm, 15.5 mm, 16 mm, 16.5 mm, 17 mm, 17.5 mm, 18 mm, 18.5 mm, 19 mm

...n: 86x88x11 mm superman: 100x70x11 mm green lantern: 79x79x11 mm batman: 90x51x10 mm aquaman: 92x77x10 mm flash:101x79x10 mm ◣_◢

...l hole (13.5 mm diameter, 2.5 mm high) is just finished, pause print, insert magnet, continue print. brim on, 0.1 mm layer height

...ed factor to 10%. setting print speed factor to 15%. setting print speed factor to 20%. print ended at: 00:35:56 and took 2:16:17

...are in millimeters: king - 73 mm queen - 66 mm bishop - 62 mm knight - 59 mm rook - 54 mm pawn - 46 mm chess board - 480x480 mm.

...el 3dexport ring 3d print model<br>size - 20 mm, h=17.3 mm<br>bracelet 3d print model<br>diam=70 mm, h=17.3 mm

...odel 3dexport ring 3d print model<br>size - 19 mm, h=14.9 mm<br>bracelet 3d print model<br>diam=70 mm, h=15 mm

... for 3d printing , two scales , for printing height 180 mm and printing height 100 mm . all parts are divided for easy printing .

...- holes were not a part of the print (slow drill on pla print worked fine for me) 126 mm l 64 mm w 19.96 mm h bottom length 20 mm

...thingiverse this bowl uses the same basic geometry as voronoibowl1 (http://www.thingiverse.com/thing:2208460), but with the voronoi shell replaced by a...

...the coffee pods. so i changed the parameters of voronoibowl1 to make it a lot larger. this one printed...

...owl1 cults this medium sized bow printed in about 23 1/2 hours using a layer height of 0.200 mm and a print speed of 100 mm/sec.

...this bowl uses the same basic geometry as voronoibowl1 (https://cults3d.com/en/home/voronoibowl1, but with the voronoi shell replaced by a hexagaonal...

...the coffee pods. so i changed the parameters of voronoibowl1 to make it a lot larger. this one printed...

...e1 by bbinnard thingiverse extensive info about this part is here: http://birkbinnard.com/blog/from-architecture-to-3d-printing/

...wiggle2 by bbinnard thingiverse large vase approx. 220 mm tall. 12 hours print time with 0.200 mm layer height.

... thingiverse this could be a small colander or fruit basket. using a layer height of 0.200 mm it printed in 16 hours 45 minutes.

...y bbinnard thingiverse a smaller, solid-walled version of previous open voronoi parts. print time 17:30 @ 0.200 mm layer height.

...first of 2 parts with the same shape. next one will have just the ribs. this print took 22 hours with a layer height of 0.200 mm.

... this vase is fairly large; the print shown here is scaled down to 65% and took 14.5 hours to print with a 0.200 mm layer height.

...amp; tray3 by bbinnard thingiverse oval-shaped planter and tray for small plants that may be too large for planter1 or planter2.

...round box with top by bbinnard thingiverse this round box has a tight fitting lid.

...e same basic geometry but has a different overall shape. it printed in a little less than 20 hours using a 0.200 mm layer height.