Thingiverse
Ultimaker 3 Drybox by Dragon2781
by Thingiverse
Last crawled date: 3 years, 1 month ago
I finished my Drybox for my Ultimaker 3 using the original spool holder with the NFC function and some additional storage for two more spools.
I used some designes so I first want to give credit to:
@UltiArjanhttps://www.thingiverse.com/thing:1837907
I used his dehumidifier basket but I had to modify it to fit my dehumidifier.
@T70Ehttps://www.thingiverse.com/thing:2559491
I used his Ultimaker 3 Spool Holder Bracket. He did an awesome job, I used it as it is.
The parts you need:
The box is a 'Orthex Clipbox Smart Store Classic 31' with 50 x 39 x 26 cm
The dehumidifier is a 'Pingi LV-A300LC' and is normally used in cars. It is rechageable.
4x angle sheet metal to support the partition boards
2x PVC board (8 mm) with ca. 40 x 8 cm (I'v sawn them off on an angle of 85°)
Strong double sided duct tape (I used '3M VHB Tape 5952F')
Q&A:
Why is there a base under the spool holder?
-> The bottom (or now the back) of the box where the spool holder is mounted will bend when the front of the spool holder is not supported by a base.
Why don't you mount the spool holder deeper to avoid using a spool holder base?
-> When you load/unload a spool you need to pull up the front part of the spool holder.
Therefore you need space below. The base of the spool holder is not mounted. It's just sitting there.
Why is there just a hole and no filament outlet?
-> I first did some outlets but the filament is on a high angle at that point and it was jamming.
I think that the Dehumidifier is able to handle that little leak.
Why do you use two PVC boards instead of one big board?
-> I don't want to seal up the two parts of the box.
I used some designes so I first want to give credit to:
@UltiArjanhttps://www.thingiverse.com/thing:1837907
I used his dehumidifier basket but I had to modify it to fit my dehumidifier.
@T70Ehttps://www.thingiverse.com/thing:2559491
I used his Ultimaker 3 Spool Holder Bracket. He did an awesome job, I used it as it is.
The parts you need:
The box is a 'Orthex Clipbox Smart Store Classic 31' with 50 x 39 x 26 cm
The dehumidifier is a 'Pingi LV-A300LC' and is normally used in cars. It is rechageable.
4x angle sheet metal to support the partition boards
2x PVC board (8 mm) with ca. 40 x 8 cm (I'v sawn them off on an angle of 85°)
Strong double sided duct tape (I used '3M VHB Tape 5952F')
Q&A:
Why is there a base under the spool holder?
-> The bottom (or now the back) of the box where the spool holder is mounted will bend when the front of the spool holder is not supported by a base.
Why don't you mount the spool holder deeper to avoid using a spool holder base?
-> When you load/unload a spool you need to pull up the front part of the spool holder.
Therefore you need space below. The base of the spool holder is not mounted. It's just sitting there.
Why is there just a hole and no filament outlet?
-> I first did some outlets but the filament is on a high angle at that point and it was jamming.
I think that the Dehumidifier is able to handle that little leak.
Why do you use two PVC boards instead of one big board?
-> I don't want to seal up the two parts of the box.
Similar models
thingiverse
free
Rubbermaid Drybox Holder for CR10
...er to switch out rubbermaid dryboxes, instead of using one dedicated drybox and having to switch out filament spools when needed.
thingiverse
free
Vector 3 top mount spool holder by NickX
...lose if using a 1kg spool
rescaled to fit on the vector 3 print bed
you will need some pvc pipe and some strong double sided tape
thingiverse
free
Filament Spool Holder (Clamp to Shelf) by DDD_guy
... suggest another (or more) arm to support multiple spools. you'll also need two 3/4" end caps to hold the pvc in place.
thingiverse
free
Angled filament holder for Ultimaker 2 and flex filament by Noloxs
...y and the angles between the spool and the feeder.
the holder is designed for use with original ultimaker size filament spools.
thingiverse
free
Cable / Filament spool holder for the wall by hustle469
...mised, in terms of, printing time and filament usage. but it is very steady!
if you need extensions for screws, just let me know.
thingiverse
free
My IKEA Samla Drybox for 3-4 Filament Spools
... the 22 liter/6 gallon ikea samla box which will have enough space for 3-4 regular 1kg filament spools (depending on spool size).
thingiverse
free
3/4 PVC holders for Filament holder by Jhack82
...so that i can have a shorter filament holder.
edit: i ended up using a extra shelf i got from ikea's spare parts bin for $1.
thingiverse
free
support for filament hanger by Kmskelton
...stored in
use an adhesive to adhere the spool holder to the walls of the filament box
thread spools on pvc
rest pvc on the holder
thingiverse
free
Ultimaker 3 Front Mount Filament Guide by countspatula
...er - the cable cover can not be used with this guide. the white insert from the original guide can be put in this one if wanted.
thingiverse
free
Filament Spool Holder
...in mounting what i came up with may look similar to some of the other spool holders, but met...
Dragon2781
thingiverse
free
Happy Birthday (two color) by Dragon2781
...happy birthday (two color) by dragon2781
thingiverse
a happy birthday logo with a little connection-bar in two colors.
thingiverse
free
Microscope Slides Box by Dragon2781
...ilities for your microscope.
it fits:
25 slides
ocular usb camera
immersion oil
filter glass
box with glass covers for the slides
thingiverse
free
Fridge Rotary Button by Dragon2781
...ied to re-create it in tinkercad and want to share it with you.
i did 3 types with different hole sizes.
the one with 7mm fitted.
thingiverse
free
Helm Mount (Sailboat) by Dragon2781
...th you.
i recommend to print it sideways to get vertical layer lines.
that way it can resist the bending when you mount the helm.
thingiverse
free
Fuel Cap Tool by Dragon2781
...' or abs for the 'blade'.
layer hight = 0.1mm
infill of the blade = 100%
infill of the handle = 30%
no support needed
thingiverse
free
Miele Nozzle Adapter for Silicone hose by Dragon2781
...er to add a 10x14mm silicone hose. i use it to clean lego sets so i added a 'lego-brick-safety-filter'.
no support needed
thingiverse
free
Samus Gunship (Metroid) by Dragon2781
...till have to keep track of what part comes to what side (left, right or front) so please take a look at the file names.
have fun!
thingiverse
free
Metal Gear Rex with Stand (Metal Gear Solid) by Dragon2781
...way you have the best surface on top. i reccomend to keep the alignment as it is.
i used a lot of pva support to print the parts.
thingiverse
free
Fan Ring Light by Dragon2781
...ratel mini usb table fan, 12,5 cmhttps://www.amazon.de/gp/product/b07r5hksyl/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=utf8&psc=1
thingiverse
free
Aircon Exhaust Adapter by Dragon2781
...online service where i can order a pre-cut acryl window with the cut out of the rectangular exhaust and six holes for the clamps.
Drybox
thingiverse
free
Filament Drybox Trockenbox
...filament drybox trockenbox
thingiverse
i use this drybox for the storagebox of my filament.
thingiverse
free
Gravity Rewinder Drybox
...files. any future updated files and instructions have moved to https://www.prusaprinters.org/prints/25858-gravity-rewinder-drybox
thingiverse
free
Drybox nozzle by Shiyaku
...drybox nozzle by shiyaku
thingiverse
for 1.75mm
thingiverse
free
Drybox filament passthrough port by GameFan
...d into the wall of a drybox through a 12mm - 13mm hole and screwed into place from the other side.
suitable for 1.75mm filament.
thingiverse
free
Drybox Filament Tap
... drybox and screw the parts together from both sides. optionally add a suitable o-ring or some silicone to increase airtightness.
thingiverse
free
Samla Drybox Spool Holders
...d spools for ikea samla 22l drybox. measure your tube diameter and use openscad or online custimizer to create required stl files
thingiverse
free
M8 rod holder for Drybox
...with counterpart by wtlx.
i changed the cutouts for the nuts to be on the inside parts.
holds an m8 rod. mounting hardware is m3.
thingiverse
free
Silica gel container for Ikea 365 drybox
...silica gel container for ikea 365 drybox
thingiverse
modified silica gel box without hygrometer for the drybox from twotone74.
thingiverse
free
Filament drybox Lid with Window by Lambcook
...filament drybox lid with window to enable the spool to be seen. glue clear plastic film, such as spool wrapping, over the window.
thingiverse
free
Hefty Drybox by hayseedbyte
...hefty drybox by hayseedbyte
thingiverse
just a quick base to hold pvc in the bottom of a hefty air-tight container.
Ultimaker
3d_export
$5
deer christmas 3
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
deer christmas 2
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
deer christmas
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
deer christmas 5
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
papa noel - santa claus
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
hippopotamus planter pot
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
decoration planter pot cute girl 15
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
decoration planter pot cute girl 14
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
deer christmas 6 3d print model
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3d_export
$5
cute fat groot
...should use a good 3d printing software such as “ultimaker cura” with the option; “remove all holes” activated or...
3
turbosquid
$10
Mountain Bike 3 -3 of 3
...model mountain bike 3 (#3 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438752)
turbosquid
$6
Rock 3-3
...urbosquid
royalty free 3d model rock 3-3 for download as obj on turbosquid: 3d models for games, architecture, videos. (1628065)
turbosquid
$29
Books 150 pieces 3-3-3
...books 150 pieces 3-3-3 for download as max, obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1384033)
turbosquid
$3
Genesis 3 Clothing 3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
hinge 3
...hinge 3
3dexport
hinge 3
3ddd
$1
Розетка 3
...розетка 3
3ddd
розетка
розетка 3
turbosquid
$50
is-3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Mountain Bike 3 -2 of 3
...model mountain bike 3 (#2 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438750)
turbosquid
$10
Mountain Bike 1 -3 of 3
...model mountain bike 1 (#3 of 3) for download as fbx and blend on turbosquid: 3d models for games, architecture, videos. (1438743)
3d_export
$5
3 CATS
...3 cats
3dexport
3 cats pen holder