Thingiverse
TuneFast Harp by makefast
by Thingiverse
Last crawled date: 3 years ago
The TuneFast Harp is a 3D printed musical instrument that uses a single-string to create an 8-note diatonic harp.
The total cost with all hardware is under $7 per harp and only takes around 3 hours to print.
Hear what it sounds like with a metal string https://youtu.be/fx9zlmGFXBQ and with a nylon string https://youtu.be/yGjTQOmBWsM.
UPDATE: A new version of the harp (AHarp22_v04.stl, shown below with blue PLA) has been modified from the original to include a parabolic sound reflector (focusing the sound 8-10cm away from the string) and a clipped corner (to reduce total material used). Files are also included to print your own M3 washers and the final M3 spacer to reduce the parts list a bit.
--
We designed the harp to be easy to assemble and fairly quick to print so that even young makers with shared resources could try it out as makerspace/classroom projects.
Parts List
You’ll need a handful of parts to complete this project. Everything is reasonably inexpensive, but many of the parts come in larger packs so you may want to plan to make a few and scale your quantities accordingly.
Here’s what you’ll need for each harp:
1 x Right-handed Guitar Tuner ($1.25/each, typically comes in a pack of 6)
9 x M3x20mm bolts/nuts (~$0.10/each for large quantities; or consider a M3 bolts/nuts multipack)
8 x 3124mm V-Groove Bearings ($0.33/each, comes in pack of 20 but account for the possibility of a couple bad bearings per pack at these prices)
1 x Nylon guitar string ($0.50/each, or use 25-50 lb test fishing line). You can also use a thin metal guitar string (9-17 gauge) but be careful not to over tighten.
~100g of PLA (or similarly rigid filament) to print the parts:
1 x harp base (file: AHarp20_v07.stl)
1 x final spacer (file: AHarp21_v03_M3Bushing_6x4.stl)
9 x washer (file: AHarp21_v03_M3Washer.stl)
Optional parts (for those with washers/spacers around):
1 x M3 6x4 Spacer ($0.35/each, or use a nylon spacer if you prefer)
9 x M3 Belleville Washer ($0.07/each, sold in packs of 100)
Print It Out
Our print time came out to around 3 hours total on a TAZ6 printing PLA with high speed settings and 30% infill.
Generally, the harp works well printed with fairly large layer heights (i.e. coarse/fast settings), but make sure you use at least 30% infill (to increase strength) and print with stiff plastic (PLA works well; ABS is strong, but it’s significantly less stiff than PLA and that’s what we’re looking for here).
Assemble the Harp
After the print is complete, remove it from the print bed and clean up any defects from the print process (we didn’t really need to do anything, but your mileage may vary depending on which printer/filament you use). In particular, make sure there aren’t any extra strands or printer blobs that would interfere with the bearings.
Add the 8 bearings using an M3x20mm bolt, nut, and washer (we prefer metal belleville washers, but you can even print your own M3 washers). The washer should go between the bearing and the printed part to keep the bearing from touching and interfering with its ability to smoothly rotate. Tighten the bolt firmly, but not so tight that it causes the bearing to rub.
Next, add the spacer for the shortest/highest note (we don't use a bearing here because of space constraints and the minimal displacement under tension so close to the end of the string).
Now, double check that each of the bearings can rotate smoothly. If there’s additional friction in any of the bearings, the string won’t be under uniform tension and thus alter the relative tuning of some of the notes. If any bearing is rubbing, just loosen it, inspect/clean any surfaces, and slowly re-tighten.
Then install the guitar tuner in the remaining hole. Hand tighten in place with the knob facing outward. Screw it in place from the bottom and fully tighten the nut.
Finally, string it up. If using a ball end string (common for electric guitar strings), just feed it through the small hole by the spacer. If using a nylon string, tie a knot in it first near the end then feed it through.
Now weave the string back and forth, holding it firmly enough that it doesn’t slide off of the bearings as you go. After the last bearing, thread the string through the hole in the metal shaft of the tuner and turn the knob to tighten it in place. Bring the string just upto tension so it holds in place for tuning. Trim off any excess string that sticks out past the tuning peg so it doesn’t get in the way or poke you later.
Tune It Up
Since all of the notes are produced from a single string under constant tension, all of the notes should be relatively in tune as soon as the string is somewhat tight. By further tightening the string, all of the notes will increase in frequency, allowing it to be tuned to any desired key.
Two things to keep in mind as you’re tuning:
You may need to sequentially push on each of the strings after adjusting the tuning to make sure the tension is even across all the notes. This is particularly important if any of the bearing are rubbing (i.e. have significantly higher friction).
You can only tighten the string so much before something bends/breaks, so adjust it slowly at first to understand its range for a given string size.
Note that the harp also works well with steel strings, but they require about twice as much tension which can deform the printed part a bit more and make it trickier to play in-tune (especially when using thicker low strings). The other downside of using a metal string is that it can be pokey/dangerous when things break or things are flopping around as you string the instrument. Just work carefully and be mindful of others around you.
Play It!
We hope you enjoy playing this experimental single-string diatonic harp. When properly built, it produces a pleasant sound and holds its tuning quite well.
The TuneFast Harp is intended to be a hands-on tool for learning about how stringed instruments work as well as a springboard for designing and printing your own custom stringed objects.
A final note for the musically inclined that feel limited by only having 8 notes to choose from: keep in mind that you can use chord inversions to play chords that go beyond the harp's limited range. For example a G Major chord (G-B-D) can be played in the 1st inversion (B-D-G) or 2nd inversion (D-G-B) to fit within the harp.
The total cost with all hardware is under $7 per harp and only takes around 3 hours to print.
Hear what it sounds like with a metal string https://youtu.be/fx9zlmGFXBQ and with a nylon string https://youtu.be/yGjTQOmBWsM.
UPDATE: A new version of the harp (AHarp22_v04.stl, shown below with blue PLA) has been modified from the original to include a parabolic sound reflector (focusing the sound 8-10cm away from the string) and a clipped corner (to reduce total material used). Files are also included to print your own M3 washers and the final M3 spacer to reduce the parts list a bit.
--
We designed the harp to be easy to assemble and fairly quick to print so that even young makers with shared resources could try it out as makerspace/classroom projects.
Parts List
You’ll need a handful of parts to complete this project. Everything is reasonably inexpensive, but many of the parts come in larger packs so you may want to plan to make a few and scale your quantities accordingly.
Here’s what you’ll need for each harp:
1 x Right-handed Guitar Tuner ($1.25/each, typically comes in a pack of 6)
9 x M3x20mm bolts/nuts (~$0.10/each for large quantities; or consider a M3 bolts/nuts multipack)
8 x 3124mm V-Groove Bearings ($0.33/each, comes in pack of 20 but account for the possibility of a couple bad bearings per pack at these prices)
1 x Nylon guitar string ($0.50/each, or use 25-50 lb test fishing line). You can also use a thin metal guitar string (9-17 gauge) but be careful not to over tighten.
~100g of PLA (or similarly rigid filament) to print the parts:
1 x harp base (file: AHarp20_v07.stl)
1 x final spacer (file: AHarp21_v03_M3Bushing_6x4.stl)
9 x washer (file: AHarp21_v03_M3Washer.stl)
Optional parts (for those with washers/spacers around):
1 x M3 6x4 Spacer ($0.35/each, or use a nylon spacer if you prefer)
9 x M3 Belleville Washer ($0.07/each, sold in packs of 100)
Print It Out
Our print time came out to around 3 hours total on a TAZ6 printing PLA with high speed settings and 30% infill.
Generally, the harp works well printed with fairly large layer heights (i.e. coarse/fast settings), but make sure you use at least 30% infill (to increase strength) and print with stiff plastic (PLA works well; ABS is strong, but it’s significantly less stiff than PLA and that’s what we’re looking for here).
Assemble the Harp
After the print is complete, remove it from the print bed and clean up any defects from the print process (we didn’t really need to do anything, but your mileage may vary depending on which printer/filament you use). In particular, make sure there aren’t any extra strands or printer blobs that would interfere with the bearings.
Add the 8 bearings using an M3x20mm bolt, nut, and washer (we prefer metal belleville washers, but you can even print your own M3 washers). The washer should go between the bearing and the printed part to keep the bearing from touching and interfering with its ability to smoothly rotate. Tighten the bolt firmly, but not so tight that it causes the bearing to rub.
Next, add the spacer for the shortest/highest note (we don't use a bearing here because of space constraints and the minimal displacement under tension so close to the end of the string).
Now, double check that each of the bearings can rotate smoothly. If there’s additional friction in any of the bearings, the string won’t be under uniform tension and thus alter the relative tuning of some of the notes. If any bearing is rubbing, just loosen it, inspect/clean any surfaces, and slowly re-tighten.
Then install the guitar tuner in the remaining hole. Hand tighten in place with the knob facing outward. Screw it in place from the bottom and fully tighten the nut.
Finally, string it up. If using a ball end string (common for electric guitar strings), just feed it through the small hole by the spacer. If using a nylon string, tie a knot in it first near the end then feed it through.
Now weave the string back and forth, holding it firmly enough that it doesn’t slide off of the bearings as you go. After the last bearing, thread the string through the hole in the metal shaft of the tuner and turn the knob to tighten it in place. Bring the string just upto tension so it holds in place for tuning. Trim off any excess string that sticks out past the tuning peg so it doesn’t get in the way or poke you later.
Tune It Up
Since all of the notes are produced from a single string under constant tension, all of the notes should be relatively in tune as soon as the string is somewhat tight. By further tightening the string, all of the notes will increase in frequency, allowing it to be tuned to any desired key.
Two things to keep in mind as you’re tuning:
You may need to sequentially push on each of the strings after adjusting the tuning to make sure the tension is even across all the notes. This is particularly important if any of the bearing are rubbing (i.e. have significantly higher friction).
You can only tighten the string so much before something bends/breaks, so adjust it slowly at first to understand its range for a given string size.
Note that the harp also works well with steel strings, but they require about twice as much tension which can deform the printed part a bit more and make it trickier to play in-tune (especially when using thicker low strings). The other downside of using a metal string is that it can be pokey/dangerous when things break or things are flopping around as you string the instrument. Just work carefully and be mindful of others around you.
Play It!
We hope you enjoy playing this experimental single-string diatonic harp. When properly built, it produces a pleasant sound and holds its tuning quite well.
The TuneFast Harp is intended to be a hands-on tool for learning about how stringed instruments work as well as a springboard for designing and printing your own custom stringed objects.
A final note for the musically inclined that feel limited by only having 8 notes to choose from: keep in mind that you can use chord inversions to play chords that go beyond the harp's limited range. For example a G Major chord (G-B-D) can be played in the 1st inversion (B-D-G) or 2nd inversion (D-G-B) to fit within the harp.
Similar models
thingiverse
free
Tronxy X1 Bed Tensioner by bearofbarham
...les will need to be drilled and the tensioner secured. note do not over tighten the tensioner screw only small amounts are needed
thingiverse
free
Tunefast Harp with cone by disoculated
...hat the resonant cone tends to sound "better" when covered with the palm of your hand when playing. at least imho :)
grabcad
free
Baby Harp 11 Strings Woodworking Project Kids Harp
...ar. unfortunately i don't remember what key i tuned mine to so you're gonna have to experiment. plans are also available.
thingiverse
free
Cadet Pedals Inner Pedal Bracket Bearings by polly_wog
...od contact.
to install all of these you will need to print:
4x bearing washer
6x inner bearing spacer
2x bearing spacer w/ washer
thingiverse
free
Printrbot Simple X Tensioner v2 by Drathus
...ng tension by tightening the screw.
stl includes two parts, which are mirrors of each other; one for each end of the print bed.
thingiverse
free
TronXY X3 and X1 Tensioner Bearing Spacer by Creat3DPrints
...m wide. you could add some extra packing washers, but i also found the guide washers to be very loose.
this is a very simple fix.
thingiverse
free
Anet A8 Y-belt tensioner V2 by YoshiCat
...vot point.
i used three m3 washers on the bearings, one between the bearings and the other two between the bearing and the frame.
3dwarehouse
free
acoutic guitar with lcd
...acoutic guitar with lcd
3dwarehouse
the lcd can let you know what chords you play every time you string. #guitars
thingiverse
free
Belt idlers' spacers and washers for Tevo Tarantula by AterLux
...ng precision with 0.4 nozzle. so, the printed part should fit precisely.
do not owertight the screws.
100% infill is recommended
grabcad
free
NYLON SPACERS & NYLON WASHERS
...://www.vital-parts.co.uk/standard-nylon-washers-705-p.asp
washers:
https://www.vital-parts.co.uk/standard-nylon-washers-705-p.asp
Tunefast
thingiverse
free
TuneFast Harp - CNC Version by pXnEmerica
...tunefast harp - cnc version by pxnemerica
thingiverse
tunefast
thingiverse
free
Tunefast Harp with cone by disoculated
...hat the resonant cone tends to sound "better" when covered with the palm of your hand when playing. at least imho :)
thingiverse
free
TuneFast Harp on the Cheap by CaptObvious
... warm soldering iron, touch the spots where screws should go to. this starts the holes in the exact right spot for your hardware.
thingiverse
free
VGroove Pulley by geartechbrandon
...a vgroove pulley wheel to match specifications for the tunefast harp. two files are offered, one with exact dimensions...
thingiverse
free
Minimal Metric Washers (for M3 and M4 hardware) by makefast
...when you need them (for example, when building the tunefast ...
Makefast
thingiverse
free
Maraca with paused addition of sand by makefast
...3d printer's bed can help to reduce shrinkage.
minimize the time you pause the print to retain strong bonding between layers.
thingiverse
free
Can Chiller with paused addition of water by makefast
...ter or yourself if you pour liquid onto hot or electrified components!
more info at http://makefastworkshop.com/hacks/?p=20160920
thingiverse
free
Minimal Metric Washers (for M3 and M4 hardware) by makefast
...t a time and stocking your hardware bins so they're around when you need them (for example, when building the tunefast harp).
thingiverse
free
Finger Tracers - Preschool / Kindergarten Numbers for Learning by makefast
...sh to remix/edit to include other shapes, letters, symbols, etc. and is released as public domain (i.e. use it however you like).
thingiverse
free
Ball Bearing with paused addition of BBs by makefast
... the extruder is hot and can easily hurt yourself or your printer if you get something in the wrong place while it's running.
thingiverse
free
Belgian Speculoos Cookie Molds by makefast
...ape. while less decorative, this makes trimming off the inevitable squished-out dough much easier than scalloped or fluted sides.
thingiverse
free
LRTee: Last Resort 22mm Ventilator Tubing Splitter by makefast
... and flow restriction devices for multiple patient lung ventilation
ventilator circuit splitters - reinforced & thicker walls
thingiverse
free
Melusina Sculpture - 3D Scan of the Luxembourg Legend by makefast
...l 1883 text about melusina.
please support luxembourg's artists by visiting next time you're in the area. villmols merci!
thingiverse
free
Tunefast Harp with cone by disoculated
...a more elaborate (perhaps too much so) version of makefast#39;s tunefast harp. key features of this remix: reinforcement struts...
Harp
archibase_planet
free
Harp
...harp
archibase planet
harp musical instrument
harp n281213 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
design_connected
$16
Harp
...harp
designconnected
jørgen christensens snedkeri harp computer generated 3d model. designed by høvelskov, jørgen.
turbosquid
$18
Harp
...rp
turbosquid
royalty free 3d model harp for download as c4d on turbosquid: 3d models for games, architecture, videos. (1458753)
turbosquid
$14
Harp
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Roda / HARP 359
...roda / harp 359
3ddd
roda
roda harp 359 armchair
3d_export
$15
Harp 3D Model
...er pedal medieval musician celtic folk orchestra band musical classical classic chordophones
harp 3d model firdz3d 75447 3dexport
archive3d
free
Harp 3D Model
...harp 3d model
archive3d
harp - 3d model for interior 3d visualization.
3d_export
free
Harp
... 4096 -available formats: 3d s max _v ray blender obj -suitable for close-ups animation game interior design architectural object
turbosquid
free
Celtic Harp
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Jew's harp
...#39;s harp for download as 3ds, obj, fbx, blend, dae, and stl on turbosquid: 3d models for games, architecture, videos. (1394285)