Thingiverse
Tripod Floor Lamp
by Thingiverse
Last crawled date: 4 years, 4 months ago
This project will guide you through the step-by-step to create a Tripod Floor Lamp.
It has a lot of steps, but they are not that difficult.
List of printed parts:
3 feet, 1 for each leg
1 core to mount the legs angled
1 lamp socket mount
1 bumper to protect the vertical rod (print this in some sort of flexible filament like TPU/TPE, if you don't have this kind of filament, I bet you can use any kind of bumper)
List of non-printed parts:
Here you find the list of materials to buy if you don't have them. However you might substitute some of the items if you wish. Read carefully
3 hardwood board. 1/2 in. x 2 in. x 4 ft. I don't know much about wood and I chose poplar, you can pick any kind of wood you prefer.
1 hardwood dowel. 1/2 in. x 48 in.
1 large shade. Large: 17" diameter, 11" high.
3 big thumb screws. 1/4 in.-20 x 1 in.
3 big nuts for the thumb screws above. 1/4 in.
1 small thumb screw. #10-32 x 1/2 in.
1 small nut for the small thumb screw above.
1 lamp cord
1 bulb socket
1 lamp harp
OPTIONAL:
You can paint/stain the wood to achieve the appearance you desire.
I decided to use Danish oil
Also sprayed the thumb screws and nuts with rust oleum
Assembling instructions:
01) Use the "core" to mark on the wood board the place to drill
02) Using 1/4in drill bit, drill the holes (1 hole for each leg)
03) Paint/stain the parts you want, if you desire to do so
04) Place the nuts on the "core"
05) Put the feet in place
06) Place the legs on the core and secure them using the larger thumb screw
07) Screw the small thumb screw on the small nut
08) Glue the bumper on the tip of the small thumb screw
09) Slide the small thumb screw on it's place, fitting the nut on it's place and use a drop of glue to hold, permanently, the nut in place. Be careful, you don't want to glue the nut and thumb screw together.
10) Assemble the socket, cord and the lamp harp.
11) Put the socket inside the "socket mount".
12) Insert the dowel on the "socket mount"
13) Place the dowel on it's position and secure it tightening the small thumb screw.
14) Place the light bulb on the socket
15) Put the shade
16) Turn it on and enjoy it!!
17) If you make one hit "Post a Make"
If you like this, check my Wall Lamp.
It has a lot of steps, but they are not that difficult.
List of printed parts:
3 feet, 1 for each leg
1 core to mount the legs angled
1 lamp socket mount
1 bumper to protect the vertical rod (print this in some sort of flexible filament like TPU/TPE, if you don't have this kind of filament, I bet you can use any kind of bumper)
List of non-printed parts:
Here you find the list of materials to buy if you don't have them. However you might substitute some of the items if you wish. Read carefully
3 hardwood board. 1/2 in. x 2 in. x 4 ft. I don't know much about wood and I chose poplar, you can pick any kind of wood you prefer.
1 hardwood dowel. 1/2 in. x 48 in.
1 large shade. Large: 17" diameter, 11" high.
3 big thumb screws. 1/4 in.-20 x 1 in.
3 big nuts for the thumb screws above. 1/4 in.
1 small thumb screw. #10-32 x 1/2 in.
1 small nut for the small thumb screw above.
1 lamp cord
1 bulb socket
1 lamp harp
OPTIONAL:
You can paint/stain the wood to achieve the appearance you desire.
I decided to use Danish oil
Also sprayed the thumb screws and nuts with rust oleum
Assembling instructions:
01) Use the "core" to mark on the wood board the place to drill
02) Using 1/4in drill bit, drill the holes (1 hole for each leg)
03) Paint/stain the parts you want, if you desire to do so
04) Place the nuts on the "core"
05) Put the feet in place
06) Place the legs on the core and secure them using the larger thumb screw
07) Screw the small thumb screw on the small nut
08) Glue the bumper on the tip of the small thumb screw
09) Slide the small thumb screw on it's place, fitting the nut on it's place and use a drop of glue to hold, permanently, the nut in place. Be careful, you don't want to glue the nut and thumb screw together.
10) Assemble the socket, cord and the lamp harp.
11) Put the socket inside the "socket mount".
12) Insert the dowel on the "socket mount"
13) Place the dowel on it's position and secure it tightening the small thumb screw.
14) Place the light bulb on the socket
15) Put the shade
16) Turn it on and enjoy it!!
17) If you make one hit "Post a Make"
If you like this, check my Wall Lamp.
Similar models
thingiverse
free
Roman Pilum by dragon3318
...ooden dowel at the end of the 25 mm round timber.
glue the wooden dowel into the 8 mm hole and place the pilum rear point on top.
thingiverse
free
Doweling Jig by photoresistor
...rotect the print from the rotating drill bit, and likely glue the spacer into place so it doesn't break loose as it heats up.
thingiverse
free
Ikea Januari Mounting Plate by Madda
...can't fall out, when screwing the lamp on.
i included the sketchup files, so you can cosumize this print to fit other models.
thingiverse
free
Fold-Up Baby Gym and Play Stand by geallen3106
... the small hole in each sleeve
7) assemble two legs on each side, large flat portion of leg should be facing each other.
8) enjoy
thingiverse
free
Micrometer Stand for Mitutoyo 293 Series, etc. by tetralite
...nting ears.
the 1/4" screw, when tightened, pushes the vertical tab against the frame of the micrometer to hold it in place.
thingiverse
free
Articulated Phone Mount by 1Prelude
...iameter 11.80mm)
whatever screws you want to attach to wall (mounting plate hole diameter is 3.5mm)
can use duct-tape in a pinch!
thingiverse
free
tcp115 and ND16FA-4 5/8" speaker
...he crossover , put the tweeter in and screw the woofer in place using m4 screws
step 10:
if you need help please leave a comment
thingiverse
free
Keychain smartphone stand by jeffjiang
...nut to get your desired tilting angle. i tried with iphone 6. it works fine with most angles either landscape or portrait. enjoy!
thingiverse
free
Simple FPV ground station by HugeOne
... generix vrx slide right in. there's a place for a 5.8 ghz vtx and small mount for another dowel to hold an omni rx antenna.
thingiverse
free
X-UAV Mini Talon "Better" Motor Mount by amnesia74
...uploaded the skp file just in case you want to modify something.
printed in abs, 100% infill, 0.20mm layer thickness, no support.
Tripod
thingiverse
free
Tripod
...tripod
thingiverse
tripod
thingiverse
free
Tripod
...tripod
thingiverse
parts for assembling a tripod from printed parts, aluminum tubes and a handful of hardware.
thingiverse
free
Tripod by KaidanAlenko
...tripod by kaidanalenko
thingiverse
a tripod
thingiverse
free
Tripod by YarikYar
...tripod by yarikyar
thingiverse
simple tripod
thingiverse
free
Tripod base
...tripod base
thingiverse
this is camera base for a tripod
thingiverse
free
Simple Tripod
...simple tripod
thingiverse
simple tripod m6x18..20
thingiverse
free
Tripod by sirajs
...tripod by sirajs
thingiverse
its a laboratory style tripod.
thingiverse
free
Tripod Part Neewer Tripod by TINKERING3D
...rinting useful?'
printed at 20% infill (test part)
final piece will be printed in 100% infill
please remix to fit your tripod
thingiverse
free
Tripod for selfie
...tripod for selfie
thingiverse
a tripod for the phone holder of the selfie stick.
thingiverse
free
Painters tripod
...painters tripod
thingiverse
this painters tripod should be printable with no supports.
Floor
thingiverse
free
flooring by WonderBread09
...flooring by wonderbread09
thingiverse
flooring
thingiverse
free
floor by akallabeth
...floor by akallabeth
thingiverse
floor for howa
thingiverse
free
Floor spacer for installing laminated flooring. by rice9300
...g laminated flooring. by rice9300
thingiverse
floor spacer for installing laminated flooring to set correct distance from walls.
thingiverse
free
Door floor guide
...door floor guide
thingiverse
door floor guide
thingiverse
free
floor slab by Vifzack
...floor slab by vifzack
thingiverse
this floor slab is for a cable channel.
thingiverse
free
Cover hole in floor
...cover hole in floor
thingiverse
used to cover holes in laminate flooring
thingiverse
free
floor pattern by hintss
...floor pattern by hintss
thingiverse
i found this pattern on a floor once.
thingiverse
free
Flooring Spacer by MeditatedStone0
...ooring spacer by meditatedstone0
thingiverse
flooring spacer 1/4 - 1/2 inch, 6mm -12mm
using to install my vinyl plank flooring
thingiverse
free
Stone Floor
...stone floor
thingiverse
for gaming and modeling
thingiverse
free
floor lamp by ayanev
...floor lamp by ayanev
thingiverse
stand for floor lamp, 27x27mm wood used.
Lamp
thingiverse
free
lamp
...lamp
thingiverse
lamp
thingiverse
free
lamp - lampe by syl39
... j'ai scanné l'original, la tete penchait. :)
by against the lamp has a fault, when i scanned the original, head bent. :)
thingiverse
free
lamp housing bedroom lamp bed lamp E27 by fpvgalaxy
...lamp housing bedroom lamp bed lamp e27 by fpvgalaxy
thingiverse
lamp housing
bedroom lamp
bed lamp
for e27
thingiverse
free
Ceil lamp and floor lamp, flower lamp, loto lamp
...e stripe that is shown in the photo. (in my case the diameter of the lamp container is 4.5 cm, the stripe is about 4.7 cm approx)
thingiverse
free
Lamp
...lamp
thingiverse
lamp (oil type)
plastics are flammable !!!!!!!!!!!!!!
https://youtu.be/itzg9abcggg
thingiverse
free
Lamp
...ingiverse
table lamp made of wood.
multiplex 4mm
lamp socket e10
1 wooden plate 1200 on 600 mm
on lasercut gravograph : 30 min.
thingiverse
free
lamp vintage / lampe vintage by syl39
...lamp vintage / lampe vintage by syl39
thingiverse
this is a vintage lamp
thingiverse
free
Lamp Shade
...lamp shade
thingiverse
lamp shade for an old floor lamp
thingiverse
free
lamp/lampe- light storm- lampe tempete by syl39
...d is printed flexismat filament-
lampe tempete, les roses se trouvent sur thingiverse, la tige est imprimé en filament flexismat
thingiverse
free
Lampe Lamp Leuchte by pawliksupreme
...lampe lamp leuchte by pawliksupreme
thingiverse
leuchte für schlafzimmer