Thingiverse
Tippmann TMC Raptor Style Charging Handle by MattT32
by Thingiverse
Last crawled date: 3 years ago
Unlike the my line of Tippmann TMC triggers that are print and play with no modification, the Tippmann TMC Raptor Charging Handle takes a little bit more work to fit it into your gun. First you must cut the aluminum guide rod out of the original charging handle that came with the gun (the one you are replacing). You do this by cutting down the length of plastic on the bottom end of the charging handle that contains the aluminum guide rod. After you have the rod free from the original charging handle, I recommend trimming the rod at the end that goes into the charging handle by .05inches to get a proper fit. Next is the hard part because you have to wait. You have to either glue or epoxy the guide rod into the Raptor Charging Handle. Squeeze a little bit into the hole that the rod will go into, and a little on the rod itself, and insert it into the hole, and make sure you push it in all the way for a proper fit, you should know its all the way in when you know longer hear air bubbles rushing out when you push on it. Then wait until the glue is cured. Also a few individuals pointed a problem out to me, I design all my parts in US Imperial Inches as it is easier for me to visualize inches than millimeters, so be sure when you import any of my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
Similar models
thingiverse
free
Tippmann TMC A4 16inch Handguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC R5 Style Handguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Skeletonized Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC CMC Flat Style Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Elftman Style Skeletonized Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Blade Style Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Aero Precision M4E1 Style Handguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Troy Style Hanguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC mag speed loader and winder by titchgamer
... "squared" prototype stl's as well as the curved edged version incase anyone would want them.
please enjoy.
thanks.
thingiverse
free
Tippmann TMC Mag Winder by mostman
...ns.
one for use as a "keyring", snug fit so it stays in place.
two to use with a bit screw, one snug fit and one loose.
Mattt32
thingiverse
free
Tippmann TMC Ambidextrous Safety Lever by MattT32
...anufacturing difficulty, it is highly recommended that you do not print this part until it is confirmed to be a finished product.
thingiverse
free
Tippmann TMC Skeletonized Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Blade Style Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC LVOA Handguard by MattT32
...rs and then scale the design as it may throw some of the important measurements off and affect how the handguard fits as a whole.
thingiverse
free
Tippmann TMC CMC Flat Style Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Elftman Style Skeletonized Trigger by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC A4 16inch Handguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC R5 Style Handguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Troy Style Hanguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
thingiverse
free
Tippmann TMC Aero Precision M4E1 Style Handguard by MattT32
...my parts into your slicer, that you convert it to millimeters or change your slicer settings to inches to match the parts design.
Tippmann
thingiverse
free
CROSS M4 TIPPMANN 98/BT4 by tippmann
...8/bt4 by tippmann
thingiverse
bonjour,
j'ai un copain qui a cassé la parti intérieur de ça cross du coup je lui est refait.
thingiverse
free
Tippmann TCR TIPX Magazin Cap
...tippmann tcr tipx magazin cap
thingiverse
tippmann tcr tipx
thingiverse
free
Tippmann Cronus double trigger by mcmari
...tippmann cronus double trigger by mcmari
thingiverse
double trigger for tippmann cronus
thingiverse
free
M16 Buttstock for Tippmann TMC by Furry_F0X
...m16 buttstock for tippmann tmc by furry_f0x
thingiverse
m16 buttstock for tippmann tmc
thingiverse
free
Spinner by tippmann
...spinner by tippmann
thingiverse
bonjour, voici mon petit spinner
dimmensoin: 80x30mm
roulement utilisé: https://goo.gl/so9kqh
thingiverse
free
Buffer tube for Tippmann TMC by Furry_F0X
...ube for tippmann tmc by furry_f0x
thingiverse
this is a buffer tube for tippmann tmc. in case the factory one is broken or lost.
thingiverse
free
tippmann a5 buttstock by colonel_fr
...o buttstock for a paintball marker tippmann a5 that will match pretty good with ak47 or mp5 customizations
tip me - i'm broke
thingiverse
free
Pom Maker by tippmann
...pom maker by tippmann
thingiverse
pom maker
tuto: https://www.youtube.com/channel/ucpxe9zmqt6iytx-vfjeawgg
thingiverse
free
Tippmann 98 handle by Idiots_YouTube
...m attempting to make a nerf conversion of the tippmann 98, this will be put up within the month hopefully and will be successful.
thingiverse
free
Tippmann TCR Rear stock Picatinny by JJwyld
...tippmann tcr rear stock picatinny by jjwyld
thingiverse
this is to replace the mag holder on the rear stock of a tippmann tcr
Tmc
thingiverse
free
M16 Buttstock for Tippmann TMC by Furry_F0X
...m16 buttstock for tippmann tmc by furry_f0x
thingiverse
m16 buttstock for tippmann tmc
thingiverse
free
TMC dummy detent by fango1986
...tmc dummy detent by fango1986
thingiverse
.
thingiverse
free
TMC Paintball Wallmount by HappyHippoSnack
...tmc paintball wallmount by happyhipposnack
thingiverse
thingiverse
free
Buffer tube for Tippmann TMC by Furry_F0X
...ube for tippmann tmc by furry_f0x
thingiverse
this is a buffer tube for tippmann tmc. in case the factory one is broken or lost.
thingiverse
free
G36 KIT FOR PAINTBALL TIPPMAN TMC by alextribal
...g36 kit for paintball tippman tmc by alextribal
thingiverse
g36 kit for paintball tippman tmc
thingiverse
free
TMC Blackbeard V1.0
...changes and adaptations will follow.
the model may only be used for private purposes.
used for original handguard (tippmann tmc)
thingiverse
free
paintball tippmann TMC end cap by froNg
...paintball tippmann tmc end cap by frong
thingiverse
stock buffer tube replacement (reversible) for stock removal on tippmann tmc
thingiverse
free
TMC hand guard by Lauer3D
...ports only on the bed if you print as shown.
once printed, slide into the marker and drill out the mounting screw hole as needed.
thingiverse
free
Tippmann TMC HK416 Adapters
... which consists of two parts near the delta ring.
the barrel: freak to t98 adapter, freak back, freak 10" front apex adapter
thingiverse
free
TMC Paintball Wallmount by HappyHippoSnack
...it.
takes quiet long to print.
you need 6 screws and thats it. have fun :)
dont use pla! i think it will break, use at least petg
Raptor
thingiverse
free
Raptor by Boba_fps
...raptor by boba_fps
thingiverse
raptor
thingiverse
free
robotic raptor
...robotic raptor
thingiverse
raptor
thingiverse
free
Raptor Zapper2
...raptor zapper2
thingiverse
a mathematical sculpture - it resembles a raptor-like shape.
thingiverse
free
RAPTOR by vittweet
...raptor by vittweet
thingiverse
it is attack plane model the raptor from the avatar.
thingiverse
free
Raptor by xXJordanXxC
...raptor by xxjordanxxc
thingiverse
3d raptor
mouth is a little messy but looks amazing
thingiverse
free
Space Raptor head
...space raptor head
thingiverse
raptor
thingiverse
free
Ford Raptor by Mooffyman13
...ford raptor by mooffyman13
thingiverse
ford raptor
thingiverse
free
ford raptor by fevold
...ford raptor by fevold
thingiverse
ford raptor
thingiverse
free
Semirealistic Raptor by Navy_Workshop
...semirealistic raptor by navy_workshop
thingiverse
fursuit raptor base
thingiverse
free
Ford Raptor by fevold
...ford raptor by fevold
thingiverse
a model of a ford raptor
Charging
thingiverse
free
Fitbit Charge HR Charging Stand by philmcglass
... stand by philmcglass
thingiverse
a simple stand or holder for a fitbit charge hr for when the fitbit is not in use or charging.
thingiverse
free
Charge Arc
...charge arc
thingiverse
simple 45 degree charge arc for placing on the corner of units.
thingiverse
free
Fitbit Charge 2 Vertical Charging Stand by rickyzega
...harge 2 vertical charging stand by rickyzega
thingiverse
a vertical stand for docking a fitbit charge 2 while it's charging.
thingiverse
free
Cavalry charging
...cavalry charging
thingiverse
1800-1860 cavalry charging. this is french, russian, prussian or austrian cavalry.
thingiverse
free
Charge-Stack (Mobile phone charging stack)
...one charging stack)
thingiverse
a solution to tidy mobile phones on your desk, when you have multiple devices to charge at once.
thingiverse
free
Fitbit Charge HR Charging Clip by rikkert278
...ging.
very simple, quick and non polished design. but, it works! :d
openscad file is provided, feel free to remix and improve :)
thingiverse
free
M5Stack Charging stand
...m5stack charging stand
thingiverse
m5stack charging stand
thingiverse
free
CHARGE IPHONE by cbottone
...charge iphone by cbottone
thingiverse
support for charge apple iphone
thingiverse
free
Garmin Charging Adapter for Vogek Charging Station by rflemming
.... see the photos for reference.
https://www.amazon.com/charging-organizer-identification-smartphones-tablets-black/dp/b07fqfnfwx
thingiverse
free
Charging Doc by Fraunziii
...charging doc by fraunziii
thingiverse
samsung 3 in 1 charging doc.
Style
thingiverse
free
bracelet styles by aramisi
...bracelet styles by aramisi
thingiverse
bracelet styles
thingiverse
free
Style Builiding by nagato
...style builiding by nagato
thingiverse
style builiding
thingiverse
free
House Style by nagato
...house style by nagato
thingiverse
house style
thingiverse
free
Styling CORRIDOR by NANCHI
...styling corridor by nanchi
thingiverse
styling corridor
thingiverse
free
Sword Samurai Style
...sword samurai style
thingiverse
samurai style sword.
thingiverse
free
L89 Style Hood
...l89 style hood
thingiverse
1/25th scale l89 style hood
thingiverse
free
Fillamentum swatch style
...fillamentum swatch style
thingiverse
fillamentum swatch style: https://fillamentum.com/collections/samples_swatches
thingiverse
free
graffiti style by atze_peng
...graffiti style by atze_peng
thingiverse
hip hop dont stop!
3d graffiti style _ mebes
thingiverse
free
DECORATION STYLE CODING
...decoration style coding
thingiverse
a decoration in the style of coding > _
(no bicolor file)
blog : bit.ly/leofactory
thingiverse
free
MWO Style Thorn
...mwo style thorn
thingiverse
a work in progress on the thorn in an mwo style. version 3 coming soon!
Handle
thingiverse
free
handle
...handle
thingiverse
handle
thingiverse
free
handle
...handle
thingiverse
just a handle
thingiverse
free
handle
...handle
thingiverse
basic utencil handle
thingiverse
free
Handle lid handle cooked by ovidiun
...handle lid handle cooked by ovidiun
thingiverse
handle lid handle cooked , have inserted one nut m6
thingiverse
free
Handle, Halter, Goodman Handle by Ralf01
...handle, halter, goodman handle by ralf01
thingiverse
this is a handle for one torch for diving
thingiverse
free
Crank Handle
...crank handle
thingiverse
crank handle for any application that needs a handle for turn.
thingiverse
free
Handle, Halter, Goodman Handle by Ralf01
...handle, halter, goodman handle by ralf01
thingiverse
i designed this handle for my diving torch.
thingiverse
free
handle by Avtonomys
...handle by avtonomys
thingiverse
handle
thingiverse
free
Handle by Rustam
...handle by rustam
thingiverse
handle
thingiverse
free
Handle by TheBrunoSan
...handle by thebrunosan
thingiverse
a handle