Thingiverse
The "OptiCooler" dual fan duct part cooling solution for Wanhao Di3 by printingotb
by Thingiverse
Last crawled date: 3 years, 1 month ago
If this helped you, consider sending a tip to:
paypal.me/JonasIdebrant
What
This is a dual blower cooler that I have worked on for over a year in different variations.
It is designed to meet my specific requirements and I believe it turned out to perform really well. Also see my overhang-test: https://www.thingiverse.com/thing:2932808
The water test to see where the air goes is made at 50% fan speed:https://youtu.be/R7mXLyg_j9s
It prints without support and is relatively lightweight at 80g including all hardware. The stock fan and shroud weighs in at 60g. The fans and funnels are snap-on, making them easy to change or replace.
Why
Powerful 360° cooling at an acceptable noise level.
You may need to PID-tune after installing but I have made sure that the airflow cools the heated block very little.
Using two instead of one blowers allows me to run them slower for the same cooling effect, reducing noise.
When used at high speeds, it is possible to print overhangs and small parts faster, since with less effective cooling you would otherwise have to slow down in order for the part to cool enough between layers.
The nozzle is visible and accessible.
Since the funnels are snap on, it is really easy to work on the hotend without having to remove anything else.
Easy installation with only two screws.
Performance
I can print smooth overhangs well up to 70° and acceptable up to 75° at 0,2mm layer height.
I can print textured overhangs well up to 60° and acceptable up to 75°.
The cooling is even around an octagonal (8-sided) test-object with edges starting to curl up at 75°, in equal amounts on all sides.
Compatibility
V2.1 printers: Print the "SpacerPlasticblock"
V2.0 printers: Print the "SpacerAlublock", you need to tap the threads in the block all way through.
PLUS versions: Print the files beginning with PLUS... (no spacer needed)
Hotends: Works with the stock and Microswiss hotends.
The fan-bracket is adjustable in height and should hopefully work with the most common other hotends, like the E3D. It can be lowered 8mm. Let me know if it still doesn't work for you.
Feel free to remix this. (The Fusion 360 files are nightmare to edit. Use for reference)
Hardware needed:
Two 5015 blowers (get the correct voltage for your printer model). I recommended Sunon maglev. Europe: https://www.tme.eu/gb/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/
United States: https://www.digikey.com/products/en?mpart=MF50151VX-B00U-A99&v=259
Or: https://www.mouser.com/ProductDetail/sunon/mf50151vx-b00u-a99/?qs=EU6FO9ffTwfWIV5p3irB3g==&countrycode=US¤cycode=USD&fbclid=IwAR0wFwurbNkWSzftGayX_IARcvQ_58TQiMcHtuWG8VU60ZEf5CpqTO88v6s
A suitable connector to the wires (You need to get double wires in the connector, or just improvise without a connector).
Two M4x25mm (M4x20 works for the plus version)
Either hot glue or two M4x35mm and nuts for connecting the fans to each other. I use hot glue.
Print recommendations
0,16mm layer height.
3 walls for the FanBracket
4 walls for the Spacer
0% infill on all
You probably need a brim on the funnels.
If you are only printing at PLA temps, you can use PLA for this. PETG or ABS is recommended for anything hotter. But make sure you can print them with good layer adhesion. The funnels are only two walls thick.
Post porcessing
Break away the "Break away support" from the FanBracket.
Thoroughly remove any brim from the funnels .
Installation
See pictures
Assemble the screws, spacer and funnels.
Install it on the machine, the screws goes in the lower bearing block.
Make sure that the funnels are centred around the nozzle before tightening.
(If necessary, the entire hotend can be moved slightly by loosening the two screws holding the cold block from beneath).
Make sure the funnels are about 1-1.5mm above the nozzle.
Shorten the wires if you want.
Connect and solder the black wires to each other and the red wires to each other.
Use a suitable connector if you have one or improvise. Black goes to black, red to red.
Install the fans either one at a time and glue, screw or cable tie them together afterwards.
Or glue them together before installation and snap them in place. Insert the inner fan's left side first and then press down the outer fan.
Pro tip: preheat the fans on the heated bed at 50° to make the hot glue adhere well and give you some time for adjustment.
Check that the heater cartridge wires are not in contact with the funnels. Carefully bend them away if needed.
Re-check that the funnels are centred and print away! I usually print PLA at 50-75% (with the really powerful Sunon blowers).
If the hotend is having trouble keeping the temp up, do a PID-tune with the fans enabled at around 50% or what % you think you will print at.
Let me know if something is unclear!
paypal.me/JonasIdebrant
What
This is a dual blower cooler that I have worked on for over a year in different variations.
It is designed to meet my specific requirements and I believe it turned out to perform really well. Also see my overhang-test: https://www.thingiverse.com/thing:2932808
The water test to see where the air goes is made at 50% fan speed:https://youtu.be/R7mXLyg_j9s
It prints without support and is relatively lightweight at 80g including all hardware. The stock fan and shroud weighs in at 60g. The fans and funnels are snap-on, making them easy to change or replace.
Why
Powerful 360° cooling at an acceptable noise level.
You may need to PID-tune after installing but I have made sure that the airflow cools the heated block very little.
Using two instead of one blowers allows me to run them slower for the same cooling effect, reducing noise.
When used at high speeds, it is possible to print overhangs and small parts faster, since with less effective cooling you would otherwise have to slow down in order for the part to cool enough between layers.
The nozzle is visible and accessible.
Since the funnels are snap on, it is really easy to work on the hotend without having to remove anything else.
Easy installation with only two screws.
Performance
I can print smooth overhangs well up to 70° and acceptable up to 75° at 0,2mm layer height.
I can print textured overhangs well up to 60° and acceptable up to 75°.
The cooling is even around an octagonal (8-sided) test-object with edges starting to curl up at 75°, in equal amounts on all sides.
Compatibility
V2.1 printers: Print the "SpacerPlasticblock"
V2.0 printers: Print the "SpacerAlublock", you need to tap the threads in the block all way through.
PLUS versions: Print the files beginning with PLUS... (no spacer needed)
Hotends: Works with the stock and Microswiss hotends.
The fan-bracket is adjustable in height and should hopefully work with the most common other hotends, like the E3D. It can be lowered 8mm. Let me know if it still doesn't work for you.
Feel free to remix this. (The Fusion 360 files are nightmare to edit. Use for reference)
Hardware needed:
Two 5015 blowers (get the correct voltage for your printer model). I recommended Sunon maglev. Europe: https://www.tme.eu/gb/details/mf50151vx-a99/dc12v-fans/sunon/mf50151vx-b00u-a99/
United States: https://www.digikey.com/products/en?mpart=MF50151VX-B00U-A99&v=259
Or: https://www.mouser.com/ProductDetail/sunon/mf50151vx-b00u-a99/?qs=EU6FO9ffTwfWIV5p3irB3g==&countrycode=US¤cycode=USD&fbclid=IwAR0wFwurbNkWSzftGayX_IARcvQ_58TQiMcHtuWG8VU60ZEf5CpqTO88v6s
A suitable connector to the wires (You need to get double wires in the connector, or just improvise without a connector).
Two M4x25mm (M4x20 works for the plus version)
Either hot glue or two M4x35mm and nuts for connecting the fans to each other. I use hot glue.
Print recommendations
0,16mm layer height.
3 walls for the FanBracket
4 walls for the Spacer
0% infill on all
You probably need a brim on the funnels.
If you are only printing at PLA temps, you can use PLA for this. PETG or ABS is recommended for anything hotter. But make sure you can print them with good layer adhesion. The funnels are only two walls thick.
Post porcessing
Break away the "Break away support" from the FanBracket.
Thoroughly remove any brim from the funnels .
Installation
See pictures
Assemble the screws, spacer and funnels.
Install it on the machine, the screws goes in the lower bearing block.
Make sure that the funnels are centred around the nozzle before tightening.
(If necessary, the entire hotend can be moved slightly by loosening the two screws holding the cold block from beneath).
Make sure the funnels are about 1-1.5mm above the nozzle.
Shorten the wires if you want.
Connect and solder the black wires to each other and the red wires to each other.
Use a suitable connector if you have one or improvise. Black goes to black, red to red.
Install the fans either one at a time and glue, screw or cable tie them together afterwards.
Or glue them together before installation and snap them in place. Insert the inner fan's left side first and then press down the outer fan.
Pro tip: preheat the fans on the heated bed at 50° to make the hot glue adhere well and give you some time for adjustment.
Check that the heater cartridge wires are not in contact with the funnels. Carefully bend them away if needed.
Re-check that the funnels are centred and print away! I usually print PLA at 50-75% (with the really powerful Sunon blowers).
If the hotend is having trouble keeping the temp up, do a PID-tune with the fans enabled at around 50% or what % you think you will print at.
Let me know if something is unclear!
Similar models
thingiverse
free
Turbofan für Anycubic I3 Mega S by emmka
...for the anycubic i3 mega s
the housing is specially designed for the sunon 5015 fan (mf50151vx-b00u-a99), other fans may also fit
thingiverse
free
Radial Fan Mount 32mm pipe by MughtyWinky
...nt, which connects a 50 mm radial fan (sunon mf50151vx-b00u-a99) to a 32 mm pipe. used to controll the smoker via pid controller.
thingiverse
free
Lume 3d printer fan duct by Kswiorek
...se this printer probably is known only in poland.
added a better version, that doesnt' blow so much on the hotend. (tun2.stl)
thingiverse
free
Raise3D Pro2 Front Blower Fan Mount by doctorwily
...nload the part "body1" or "duct" (i believe they are the same part):https://www.thingiverse.com/thing:3691333
thingiverse
free
Anycubic i3 Mega fan duct for 5015 radial fan by D1_
...tall the fanbox around your hotend. at least with my setup...
don´t forget to choose the "support on build plate only".
thingiverse
free
Anycubic i3 Mega Sunon Fan Mod by warmans
... it onto the wires of the new one.
note: this will reduce the print volume by 5mm on the x-axis unless you move the limit switch.
thingiverse
free
Fan duct for Anycubic i3 Mega-S by Hotte70
...he installation:
fan: sunon 50 x 50 x 15 mm mf50151vx-a99
screws: m3 x 12, 2 pieces and m3 x 20, 1 piece
screw nut: m3, 1 piece
thingiverse
free
Anycubic Mega Hotend-Housing with Air Noozle (Mega-S, Mega-X, I3-Mega) by Lupfe
... the tight space you have to make the barcket, which holds the hotend, a bit thinner, so the sunon fan can fit under the housing.
thingiverse
free
Improved Bondtech BMG + E3D V6 + BLTouch carriage for BLV MGN12
... sunon mf50151vx-b00u-a99 blower fan - i found that this had a slightly larger aperture than the generic fan i was using earlier.
thingiverse
free
E3D hotend blower fan holder by dasaki
... it fits your setup.
if you are a curious maker / "tinker" / hacker, have a look at my blog:http://www.therandomlab.com
Opticooler
thingiverse
free
Another bltouch / 3d touch mount for Wanhao i3 / Maker Select by ej0rge
...by ej0rge thingiverse since i am upgrading to the opticooler on my di3v2.1 as soon as some m4x25mm screws...
thingiverse
free
Cooling test - Overhang test by printingotb
...made this to help me design and evaluate my opticooler cooling solution for wanhao di3. (it's what i used...
3dwarehouse
free
Opticool, Rotterdam, Nederland
...opticool, rotterdam, nederland
3dwarehouse
loods aan de keilestraat
3dwarehouse
free
Opticool, Rotterdam, Nederland
...opticool, rotterdam, nederland
3dwarehouse
loods aan de keilestraat
3dwarehouse
free
Opticool, Rotterdam, Nederland
...opticool, rotterdam, nederland
3dwarehouse
loods aan de keilestraat
Printingotb
thingiverse
free
DecapiCat by printingotb
...support under the tongue and the lowest part of he head.
attached my support settings but they are by no means the best settings.
thingiverse
free
Hinges by printingotb
...tertight and suitable for 3d-printing.
i have printed these in every material i have tried. pla, abs, petg, nylon all work well.
thingiverse
free
Robo Rally Twitch upgrade by printingotb
...ree supports + a modelled custom break away support under the middle.
a total 1.5 workdays to design, print and paint.
100% happy
thingiverse
free
Curve Overhang test *halved* by printingotb
...all lines works better than more but only if you allow the bottom skin on top of the walls, see picture from cura (yellow areas).
thingiverse
free
Anycubic kossel L+ Corner Supports and Bed holder by printingotb
...ee pictures for instructions.
the top corners can be used everywhere if you only want the corner supports and not the bed holder.
thingiverse
free
Z-Brace 0.5 by printingotb
...ble "helper" to get the holes right as well as easy to follow instructions.
https://www.youtube.com/watch?v=aglek3ychea
thingiverse
free
Spool core with sides for Eco refill by printingotb
...es.
cut-out for layer seam on inner diameter.
lots of holes for attaching the filament end
designated place for material sticker.
thingiverse
free
Stepper Smoother Box by printingotb
...ave one:https://www.thingiverse.com/thing:1997411
performance
see second picture, the issue was mild on my printer to begin with.
thingiverse
free
Simple topmounted spoolholder for enclosure by printingotb
...ss.
oh, and no need to mount it so close to the edge of your enclosure, i had a leaning ceiling just above my printer before :-p
thingiverse
free
CR10 2.3kg Spool Holder for controlbox by printingotb
...realized that there is not enough space for them lol.
feel free to remix this in any way you want :)
https://youtu.be/sw5s5zl6jey
Di3
thingiverse
free
Wanhao Di3 v2 Light / Wanhao Di3 v2 Beleuchtung by JMDesigns
...wanhao di3 v2 light / wanhao di3 v2 beleuchtung by jmdesigns
thingiverse
wanhao di3 v2 light / wanhao di3 v2 beleuchtung
thingiverse
free
Wanhao Di3 MagFix System by JMDesigns
...wanhao di3 magfix system by jmdesigns
thingiverse
wanhao di3 magfix system
thingiverse
free
Wanhao Di3 Silicone Softgrip by JMDesigns
...wanhao di3 silicone softgrip by jmdesigns
thingiverse
wanhao di3 silicone softgrip
thingiverse
free
Di3 rotary dial by 3Dplanner
...hingiverse
original model of jo3ri http://www.thingiverse.com/thing:33286 , adjusted for the di3.
layer 0.2
shell 2
fill 50%
pla
thingiverse
free
Di3 LCD Angler ( With Air Vents ) by diamonddrake
...3 lcd angler ( with air vents ) by diamonddrake
thingiverse
this is a remix of rtideas di3 lcd angler, i simply added air vents.
thingiverse
free
Di3 Hex Wrench Holder by BliNDF123
...de a hex wrench holder for the ones that come with the di3, stuck it to the side frame of my printer with some double sided tape.
thingiverse
free
E3D v6 mount for Wanhao Di3 by slimc
...w design http://www.thingiverse.com/thing:1657971
set of components that allow the e3d v6 hotend to be mounted on the wanhao di3.
thingiverse
free
Wanhao Di3 V2.1 Knob Grip by Hyperlinks
...
thingiverse
this is a remix for the di3 v2.1. it did not fit properly on my printer (too tall), so i scaled it down minus 7 mm.
thingiverse
free
Wanhao Di3+ filament cleaner by Alpin3D
...wanhao di3+ filament cleaner by alpin3d
thingiverse
v1.1
filament cleaner / sponge
v1.2
better filament control
thingiverse
free
Di3 Nozzle LED Mount by sprfly
...e cooler. uses a 3 led section of self adhesive strip leds. i tapped into the always on hotend fan to provide the 12v to my leds.
Wanhao
thingiverse
free
Wanhao Logo Plate / Wanhao Logo Schild by JMDesigns
...wanhao logo plate / wanhao logo schild by jmdesigns
thingiverse
wanhao logo plate / wanhao logo schild
thingiverse
free
Wanhao logo by nebtio
...wanhao logo by nebtio
thingiverse
wanhao logo
thingiverse
free
Wanhao keychain by Rein3003
...wanhao keychain by rein3003
thingiverse
a keychain with the logo of wanhao
thingiverse
free
Wanhao Di3 v2 Light / Wanhao Di3 v2 Beleuchtung by JMDesigns
...wanhao di3 v2 light / wanhao di3 v2 beleuchtung by jmdesigns
thingiverse
wanhao di3 v2 light / wanhao di3 v2 beleuchtung
thingiverse
free
TUSH For Wanhao by wtmi1992
...tush for wanhao by wtmi1992
thingiverse
the ultimate spool holder, modified for the top of the wanhao control box. fits snug.
thingiverse
free
fanduct wanhao d12 by theopoilmek
...fanduct wanhao d12 by theopoilmek
thingiverse
fanduct pour wanhao d12
thingiverse
free
Wanhao i3 Marlin by johan21
...wanhao i3 marlin by johan21
thingiverse
marlin for wanhao i3 rampsboard 1.4.
thingiverse
free
Wanhao Duplicator i3 by imagineering4
...wanhao duplicator i3 by imagineering4
thingiverse
these are the stl files for the improvements to the wanhao duplicator i3, v2
thingiverse
free
Wanhao D6 filament guard
...wanhao d6 filament guard
thingiverse
this is a filament guard for wanhao d6 machine to avoid the filament unrolling
thingiverse
free
Wanhao Duplicator i3 Model by Hilde3D
...wanhao duplicator i3 model by hilde3d
thingiverse
wanhao duplicator i3 model
Duct
turbosquid
$19
Duct Set
...d
royalty free 3d model duct set for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1145038)
turbosquid
$10
Duct Tape
...id
royalty free 3d model duct tape for download as ma and ma on turbosquid: 3d models for games, architecture, videos. (1580351)
turbosquid
free
Duct Tape
...
free 3d model duct tape for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1486518)
3d_ocean
$7
Air-duct
... ventilation
high quality industrial air duct ventilation model. created in cinema 4d but comes in various other formats as well.
turbosquid
$20
Air ducts
...lty free 3d model air ducts for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1262476)
3d_export
$10
Supply air duct
...supply air duct
3dexport
supply air duct with two axial fans and hangers
turbosquid
$2
Duct Tape
...e 3d model duct tape for download as obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1473972)
turbosquid
free
Duct Tape
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$3
Duct tape
...polys. includes: cinema 4d project. model in 3 formats (obj, fbx, 3ds). 6 .tga texture maps (albedo, ambient occlusion, diffus...
turbosquid
$40
Ventilation Duct PACK
...tion duct pack for download as ma, obj, fbx, and unitypackage on turbosquid: 3d models for games, architecture, videos. (1287068)
Dual
turbosquid
free
Dual Pistols
...ls
turbosquid
free 3d model dual pistols for download as fbx on turbosquid: 3d models for games, architecture, videos. (1320360)
turbosquid
$2
Dual Axe
...urbosquid
royalty free 3d model dual axe for download as fbx on turbosquid: 3d models for games, architecture, videos. (1332372)
turbosquid
$10
Dual Lesaths
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
плитка Dual Bianco (Испания)
...й плитки venis dual (испания). технические качества: устойчивость к стирания, отличная геометрия, отсутствие проблем при укладке.
turbosquid
$35
Dual Mesh Fonts
...ree 3d model dual mesh fonts for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1352989)
turbosquid
$29
Dual Flask with Bungs
...del dual flask with bungs for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1210512)
turbosquid
$19
Dual Socket Plug
...3d model dual socket plug for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1303912)
turbosquid
$13
Dual Adjustable Pulley
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Amoi N809 Dual
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Dual Turret Tank
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Fan
3d_export
$5
fan
...fan
3dexport
fan 3d model, table fan, fan, electric fan, ventilator
archibase_planet
free
Fan
...fan
archibase planet
fan large fan
fan out n260707 - 3d model for interior 3d visualization.
archibase_planet
free
Fan
...fan
archibase planet
fan ceiling fan ventilator
fan stealth n300615 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$15
fan
...fan
3dexport
is an ancient fan
3ddd
$1
Fan-C-Fan by marco gallegos
...n-c-fan by marco gallegos
3ddd
вентилятор , marco gallegos
fan-c-fan by marco gallegos
3d_export
$10
fan
...fan
3dexport
a detailed fan designed for home or space blowing is now available for only 19.99!
turbosquid
$1
Fan
...fan
turbosquid
free 3d model fan for download as on turbosquid: 3d models for games, architecture, videos. (1427865)
turbosquid
$14
Fan
...fan
turbosquid
royalty free 3d model fan for download as on turbosquid: 3d models for games, architecture, videos. (1415642)
3ddd
$1
Светильник Fan
...светильник fan
3ddd
fan , italamp
светильник fan, производитель italamp
turbosquid
$25
Fan
...fan
turbosquid
royalty free 3d model fan for download as c4d on turbosquid: 3d models for games, architecture, videos. (1483246)
Cooling
turbosquid
free
Cool Inc. Cool Box
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
cool penguin
...cool penguin
3dexport
cool penguin
turbosquid
$1
cooling
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$26
cooling tower
...ers.<br>model with full detail in real size. all nodes and bolted connections are built. it was designed for nuclear power.
3ddd
$1
Mantra Cool
...14 версиях и obj-файл, а также материал для включенного и для выключенного светильника. turbosmooth/meshsmooth при необходимости.
3d_export
$5
cool electric guitar
...cool electric guitar
3dexport
cool electric guitar
turbosquid
$5
Cooling glass
...quid
royalty free 3d model cooling glass for download as obj on turbosquid: 3d models for games, architecture, videos. (1193829)
turbosquid
$30
CPU Cooling
...royalty free 3d model cpu cooling for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1386263)
turbosquid
$5
Cool CLoud
...
royalty free 3d model cool cloud for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1572300)
3d_export
$5
table cooling fan
...table cooling fan
3dexport
table cooling fan made of black plastic. individual small size cooling fan for office desk.
Solution
3ddd
$1
Grammer / Solution
... кресло
офисное кресло solution фирмы grammer office. подробнее на www.grammer-office.com
3d_export
$48
TV Solution 3D Model
...solution 3d model
3dexport
tv solution interior dvd decor gypsum cornices spotlights
tv solution 3d model mr.kiwan 19449 3dexport
3d_export
$86
architectural solution 352a1
...architectural solution 352a1
3dexport
3dsmax 2017 3dsmax 2020 fbx obj map
3ddd
$1
Светильник польского производителя Aquaform Lighting Solution
...ution
3ddd
aquaform
светильник польского производителя aquaform lighting solution
модели:
tuba 111x1 distance
tuba 111x2 distance
3d_export
$20
lift internet solutions 3
...ly model of an industrial elevator. - materials are configured in 3ds max and corona render. - formats: fbx, obj, step, max 2020.
3ddd
$1
Светильник польского производителя Aquaform Lighting Solution
...
светильник польского производителя aquaform lighting solution
серия: tuba 111
модели:
tuba 111 on
tuba 111 on 23
tuba 111 on 34
3ddd
$1
Одинарный спот польского производителя Aquaform Lighting Solution
... aquaform
одинарный спот польского производителя aquaform lighting solution
модель: zuma 90
turbosquid
$25
Triple Hair Core Set Shampoo Serum Solution
... shampoo solution serum set for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1638904)
3ddd
$1
Поворотный светильник польского производителя Aquaform Lighting Solution
...воротный светильник польского производителя aquaform lighting solutionhttp://www.aquaformlighting.com/
модель: rotto
3ddd
$1
PotteryBarn ROLLING CABINET MEDIA SOLUTION
... телевизор , роллинг
279.4cm wide x 111.8cm high x 12.06cm deep
fits most 152.4cm tvs.
Part
3d_export
$5
Parts
...parts
3dexport
parts
3d_export
$5
Part
...part
3dexport
part
3d_export
$5
Part
...part
3dexport
machine part
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$30
fan part
...fan part
3dexport
this is a part of fan of pedastal
3d_export
$10
machine parts
...machine parts
3dexport
3d part modeling work ,contact for 3d work
turbosquid
$59
Mechanical Part
...id
royalty free 3d model mechanical part for download as c4d on turbosquid: 3d models for games, architecture, videos. (1410833)
turbosquid
$17
Road parts
...bosquid
royalty free 3d model road parts for download as 3ds on turbosquid: 3d models for games, architecture, videos. (1192967)
turbosquid
$9
Cutter Parts
...squid
royalty free 3d model cutter parts for download as stl on turbosquid: 3d models for games, architecture, videos. (1220010)