Thingiverse
"The HUM Box V1" Completed (Working Prototype) and (Sneak Preview "The HUM Box V2.0" Final) by 3D_PP
by Thingiverse
Last crawled date: 3 years ago
"The HUM Box V1" (Prototype Version)
The HUM Box is a creation of inspiration, picked up from the (H)ypercube-(U)ltimaker-Ivan (M)iranda Printers, and offcourse our own Tinkered version of the Ivan Miranda printer.
....This is a Finished working prototype....
....Printvolume 200x200x230....
....All parts are printed in PLA....
....First photo gives a View from the finished Prototype....
Once you created The HUM Box and dialed it in, you will notice that there is almost no need to re-adjust the level of the bed.
Neither is there a need for dual Z-endstops or a bed leveling sensor due the sturdy bed / frame build.
Be aware, Building the frame precise (equal lengths) and square (90 degrees angles) is mandatory on the success of your printer.
The reason we created The HUM Box:
We were not satisfied with the results of the Tinkered Ivan Miranda 300mmx300mmx500mm build, it's a nice printer as long as you don't go over the height limit of about 250mm. If you do, change the build to minimum 30x30 extrusions, better even 40x40.
Also a very high amount of Z-Wobble that almost can not be reduced.
Notes for The HUM Box V1:
Keep in mind that there is a lot of plastic used as we printed all parts with 100% infill, used filing / sanding / grinding / etc to come to the end prototype models in the design.
We kept the adjusted prototype printed parts on the printer but adjusted them digital.
Still, all parts look like the prototype, the parts are not optimized yet to use a minimum of plastic.
Future enhancements:
This most likely will come in an upgraded version, The HUM Box V2 (Optimized V1 printed parts).
Possible change in the X- and Y Carriages, holding a Chimera Hotend, running on a MKS 1.4 or MKS 1.5 and mounts for 40x40mm fans so we can use Noctua fans to reduce the noise even more.
Plans are also already on the table to create The HUM Box V2-L / The HUM Box V2-XL (2019/2020 or sooner if we have the time)
Print suggestion:
The 100% infill is not needed if you want to make The HUM Box, all up to you.
Most parts will do with 20 to 40% infill, 3 parameters, 4 top and bottom layers, at 0.2 layer height. All depends how sturdy you want to make it.
Print the "Mk2 Heat Bed Bracket" and the "Z T-Nut Bracket" or "Z M8-Nut Bracket" on 100% infill to avoid bending by tension.
Be sure to have the correct settings on your printer, all depends on your calibration and filament you use, print a square and circular calibration tower first so you can measure with your parts.
We happened to have a 2.3Kg spool of filament that had a 3.5% crimp factor.
We assume you have a perfect calibrated printer with the filament you use.
You swap filament and suddenly the dimensions are not correct anymore.
Two things you can do:
Re-calculate the steps and adjust them accordingly in for example Marlin and flash the eeprom, retest, rins and repeat till it is correct again. (To much of a hassle)
Calculate the percentage deviation on the filament crimp.
How to calculate the percentage deviation:
Formula to use: 100*(measured value-old value)/old value = percentage deviation
So for example after using the square tower:
The square extrusion will not fit in 20.5, meaning the new value is 20.6
The Deviation is then 100*(20.6-20)/20 = 3%.
This means that your filament has a 3% crimp.
Take your measurements in account and add the percentage in your slicer software when printing the parts. (Done)
Re-used parts:
Some Parts are used from the Tinkered Ivan Miranda Printer.
Both the X-Carriages with the Belt Clamps and the Y-carriage with the Belt Clamps.
E3D clamp
3x bracket clamp to hold the rods in place
The Extruder Holder.
A few of the clamps with cable tray.
End of Re-used parts
The X-Carriage Motor bridge is adjusted to hold both the Y and X Limit switches so do not use it from there, a new one will be posted here.
Clean Electrical Design:
We tried to reduce the sight of loose wires, most of the times always all over the place.
Some are still visible, but either running thru a chain, or in a guide on the 20x20 extrusions.
Part List (Buyers Guide):
Below is a Part list of items to buy or items you have already laying around.
This can also be build with the 20x20 V-slot extrusions, but that will drive the price up with about 60 euro.
You can also use many parts of the Tinkered Ivan Miranda Printer to build this one.
Square extrusions Dimensions 20x20x1.5
4 x L=100 Frame Cabinet
4 x L=325 Frame Z-Direction
6 x L=426 Frame X-Direction
6 x L=314 Frame Y-Direction
2 x L=415 (Bed support)
2 x L=140 (Bed support)
8 x 20x20 Corner Bracing (3 way 90 degrees) (we bought these in the local hardware store, about 2 euro each but we took measurements and we made an stl for it so you can print them if you like. Print them with 100% infill
2 x 12mm smooth hardened rod L=475 X-Axis Motor and Idler side
2 x 12mm smooth hardened rod L=300 Y-Axis
4 x 12mm smooth hardened rod L=350 Z-Axis
1 x 8mm smooth hardened rod L=280 X-Axis Transfer rod
2 x M8 Threaded Rod L=300 (or T8-? Lead Screw) (Brackets for either will be available) (Just what you prefer to use)
14 x LM12UU Linear Bearing
1 x 608RS Bearing
3 x Flexible Threaded Coupler 5-8 mm 25mm
3 x Omron SS-5GL2
2 x Pulley GT2 20T BORE 5
1 x Pulley GT2 20T BORE 8
4 x Nema 17 42x42mm stepper motor
1 x Nema 17 42x42mm stepper motor (Dual Axis)
2 x Fan 30 x 30 12V
4 x 3mm Thumb Screws
1 x E3D V6 short version
1 x 1mtr of PTFE tube
1 x Power flip switch (On/Off), IEC 3 Pin 320 C14, 250V with 10A Fuse
1 x 12V - 30Amp Power supply
1 x 30 Amp Mosfet, we prefer the MKS version, stays very cool on use
4 x Pressure springs for the heated bed, stirdy ones: 0.9mm wire thickness, 7.2mm outer diameter, 30mm length, 14 windings, flat start end end.
1 x 12V Computer Case Fan for electronics cooling (we used an Aero Cool with 200 mm diameter)
2 x Micro- or on/off switches, best to use on/off with build in led indicator to see if a fan is on or off, used for the extruder and cabinet fan to switch off if printer is not running.
1 x Anycubic Ultrabase 200 x 200 (with Heated bed of Anycubic, complete set)
1 x 1Mtr of 10x15 Cable Chain with 2 start and 2 end connectors
1 x 1Mtr of 7x7 Cable Chain with a start and end connector
M3 / M5 Bolts / Nuts (some M5 Nyloc Nuts) different lengths
Ferrules / Crimp connectors / Electronic Wires (use correct thickness)
GT2 6mm Belt (get a roll of 5 or 10 meter, not needed but you will have spare belt in case something goes wrong)
4 mm thick Plywood to make the electronics cabinet top and bottom (2 times 350x470mm)
Your preferred board. At the moment it is running on a Ramps 1.4 with standard stepper drivers and a graphical display.
Some Thick packaging Foam to use for sound / vibration dampening.
Handy to have:
Metric Drill Bits
Metric Hand Tap Threading Tools with corresponding drill bits
End stop connections used. (If you use X-Min you will have mirrored parts)
X-Max
Y-Min
Z-Min
Parts to print:
If you don't have the parts from https://www.thingiverse.com/thing:2668054
Go over there and get the following files to print.
X-carriage_Bridge_Motor_side
Cable_holder_V2_left_hand_side (2 times needed)
Cable_holder_V2_right_hand_side (2 times needed)
Bridge_Pulley_side
Y-Carriage_with_LM12UU
Y-Carriage_Belt_clamp (2 times needed)
E3D_clamp
New parts to print:
For the bed:
Z Axis Bearing Holder 1.0 (4 times needed)
Z T-Nut Bracket 1.0 (2 times needed) (If you plan to build it with a T8 leadscrew print those)
Z M8-Nut Bracket 1.0 (2 times needed) (If you plan to build it with a M8 leadscrew print those)
Z M8 Nut Blocker 1.0 (2 times needed) (If you plan to build it with a M8 leadscrew print those)
Mk2 Heat Bed Bracket 1.0 (4 times needed)
20 x 20 End Cap 1.0 (4 times needed)
For the frame:
20 x 20 Corner Bracing (3 way 90 degrees) 1.0 (8 times needed, buy or try to print)
Frame extender 1.0 (4 times needed)
Foot 1.0 (4 times needed)
Other parts:
X-Axis Bracket Front 1.0
X-Axis Bracket Front clamp 1.0
X-Axis Bracket Front motor 1.0
X-Axis Bracket Front motor clamp 1.0
X-Axis Bracket Back 1.0
X-Axis Bracket Back clamp 1.0
X-Axis Guide bracket 1.0
X-Axis Guide bracket clamp 1.0
Y-Axis Motor Bridge 1.0
Z-Axis Support Bottom (116mm) 1.0 (2 times needed)
Z-Axis Support Top (116mm) 1.0 (2 times needed)
Z_MIN switch holder 1.0
Bracket clamp 1.0 (3 times needed)
Motor bracket clamp 1.0
Belt Tensioner 1.0 (3 times needed)
Alignment of the Z-Axis Supports:
Use "X-Axis Bracket Front clamp 1.0" to align the Z-Axis support on top and bottom, alignment taken from the front of the printer with 0.5mm space between the bracket and Z-Axis supports. Align those parts first before placing the bottom box. You can flip the bracket 180 degrees to use on the right hand side.
Notes on the build:
Be sure that the Z-Axis rods have a snug fit in the Z-Axis supports.
All brackets that needs to be placed over the square extrusions of the frame, need to have a tight fit, though not need to be placed with the use of force.
For the print bed.
All brackets need to have a loose fit, but without any play
if your brackets for the heatbed have a snug fit, you can do the following trick to get them on a loose fit.
Slide the bracket over a piece of extrusion of about 100mm. This probably will need a bit of force to get them on, be sure that the bracket is about in the center of the extrusion.
Now get yourself a soldering iron and place it inside the extrusion and let it heat up.
Be patient and careful as the extrusion will get hot. Best is to use a towel to hold the extrusion when you start working on the bracket.
If the extrusion and the printed part reach the desired temperature, you will be able to start sliding the bracket over the extrusion.
Remove the soldering iron, switch it off and put it away on a safe spot.
Remove the bracket from the extrusion, let it cool down a bit, it will cool down faster then the extrusion, then place it back on the extrusion to slide it a few more times.
You should now have a loose fit without the need of using a file or sanding.
If you need to apply to much force to get the bracket on the extrusion, file it down first as it will not work with the above trick.
When assembling the bed frame, as shown on the first picture of the printer, the Mk2 Heat Bed Bracket 1.0 needs to be mounted at a 9.2mm distance from the Z Axis Bearing Holder 1.0. On the side where the Dual axis NEMA sits.
WARNING when you start printing:
Do NOT forget to switch on your cooling, else you will end up with a clogged extruder / overheated board.
Disclaimer:
3D_PP is not responsible for any damage / injuries what so ever in any kind of degree.
Building this printer is all at your own risk, as it is with all other builds you create.
Always shut down the Main Voltage Input when working on Electronic Components.
Know what you are doing, You are working with High Voltages and high temperatures.
Take NO Risks <<<
If you like our work, consider to make a small donation so we can keep on developing.
If you made one, please share a picture of your design.
The HUM Box is a creation of inspiration, picked up from the (H)ypercube-(U)ltimaker-Ivan (M)iranda Printers, and offcourse our own Tinkered version of the Ivan Miranda printer.
....This is a Finished working prototype....
....Printvolume 200x200x230....
....All parts are printed in PLA....
....First photo gives a View from the finished Prototype....
Once you created The HUM Box and dialed it in, you will notice that there is almost no need to re-adjust the level of the bed.
Neither is there a need for dual Z-endstops or a bed leveling sensor due the sturdy bed / frame build.
Be aware, Building the frame precise (equal lengths) and square (90 degrees angles) is mandatory on the success of your printer.
The reason we created The HUM Box:
We were not satisfied with the results of the Tinkered Ivan Miranda 300mmx300mmx500mm build, it's a nice printer as long as you don't go over the height limit of about 250mm. If you do, change the build to minimum 30x30 extrusions, better even 40x40.
Also a very high amount of Z-Wobble that almost can not be reduced.
Notes for The HUM Box V1:
Keep in mind that there is a lot of plastic used as we printed all parts with 100% infill, used filing / sanding / grinding / etc to come to the end prototype models in the design.
We kept the adjusted prototype printed parts on the printer but adjusted them digital.
Still, all parts look like the prototype, the parts are not optimized yet to use a minimum of plastic.
Future enhancements:
This most likely will come in an upgraded version, The HUM Box V2 (Optimized V1 printed parts).
Possible change in the X- and Y Carriages, holding a Chimera Hotend, running on a MKS 1.4 or MKS 1.5 and mounts for 40x40mm fans so we can use Noctua fans to reduce the noise even more.
Plans are also already on the table to create The HUM Box V2-L / The HUM Box V2-XL (2019/2020 or sooner if we have the time)
Print suggestion:
The 100% infill is not needed if you want to make The HUM Box, all up to you.
Most parts will do with 20 to 40% infill, 3 parameters, 4 top and bottom layers, at 0.2 layer height. All depends how sturdy you want to make it.
Print the "Mk2 Heat Bed Bracket" and the "Z T-Nut Bracket" or "Z M8-Nut Bracket" on 100% infill to avoid bending by tension.
Be sure to have the correct settings on your printer, all depends on your calibration and filament you use, print a square and circular calibration tower first so you can measure with your parts.
We happened to have a 2.3Kg spool of filament that had a 3.5% crimp factor.
We assume you have a perfect calibrated printer with the filament you use.
You swap filament and suddenly the dimensions are not correct anymore.
Two things you can do:
Re-calculate the steps and adjust them accordingly in for example Marlin and flash the eeprom, retest, rins and repeat till it is correct again. (To much of a hassle)
Calculate the percentage deviation on the filament crimp.
How to calculate the percentage deviation:
Formula to use: 100*(measured value-old value)/old value = percentage deviation
So for example after using the square tower:
The square extrusion will not fit in 20.5, meaning the new value is 20.6
The Deviation is then 100*(20.6-20)/20 = 3%.
This means that your filament has a 3% crimp.
Take your measurements in account and add the percentage in your slicer software when printing the parts. (Done)
Re-used parts:
Some Parts are used from the Tinkered Ivan Miranda Printer.
Both the X-Carriages with the Belt Clamps and the Y-carriage with the Belt Clamps.
E3D clamp
3x bracket clamp to hold the rods in place
The Extruder Holder.
A few of the clamps with cable tray.
End of Re-used parts
The X-Carriage Motor bridge is adjusted to hold both the Y and X Limit switches so do not use it from there, a new one will be posted here.
Clean Electrical Design:
We tried to reduce the sight of loose wires, most of the times always all over the place.
Some are still visible, but either running thru a chain, or in a guide on the 20x20 extrusions.
Part List (Buyers Guide):
Below is a Part list of items to buy or items you have already laying around.
This can also be build with the 20x20 V-slot extrusions, but that will drive the price up with about 60 euro.
You can also use many parts of the Tinkered Ivan Miranda Printer to build this one.
Square extrusions Dimensions 20x20x1.5
4 x L=100 Frame Cabinet
4 x L=325 Frame Z-Direction
6 x L=426 Frame X-Direction
6 x L=314 Frame Y-Direction
2 x L=415 (Bed support)
2 x L=140 (Bed support)
8 x 20x20 Corner Bracing (3 way 90 degrees) (we bought these in the local hardware store, about 2 euro each but we took measurements and we made an stl for it so you can print them if you like. Print them with 100% infill
2 x 12mm smooth hardened rod L=475 X-Axis Motor and Idler side
2 x 12mm smooth hardened rod L=300 Y-Axis
4 x 12mm smooth hardened rod L=350 Z-Axis
1 x 8mm smooth hardened rod L=280 X-Axis Transfer rod
2 x M8 Threaded Rod L=300 (or T8-? Lead Screw) (Brackets for either will be available) (Just what you prefer to use)
14 x LM12UU Linear Bearing
1 x 608RS Bearing
3 x Flexible Threaded Coupler 5-8 mm 25mm
3 x Omron SS-5GL2
2 x Pulley GT2 20T BORE 5
1 x Pulley GT2 20T BORE 8
4 x Nema 17 42x42mm stepper motor
1 x Nema 17 42x42mm stepper motor (Dual Axis)
2 x Fan 30 x 30 12V
4 x 3mm Thumb Screws
1 x E3D V6 short version
1 x 1mtr of PTFE tube
1 x Power flip switch (On/Off), IEC 3 Pin 320 C14, 250V with 10A Fuse
1 x 12V - 30Amp Power supply
1 x 30 Amp Mosfet, we prefer the MKS version, stays very cool on use
4 x Pressure springs for the heated bed, stirdy ones: 0.9mm wire thickness, 7.2mm outer diameter, 30mm length, 14 windings, flat start end end.
1 x 12V Computer Case Fan for electronics cooling (we used an Aero Cool with 200 mm diameter)
2 x Micro- or on/off switches, best to use on/off with build in led indicator to see if a fan is on or off, used for the extruder and cabinet fan to switch off if printer is not running.
1 x Anycubic Ultrabase 200 x 200 (with Heated bed of Anycubic, complete set)
1 x 1Mtr of 10x15 Cable Chain with 2 start and 2 end connectors
1 x 1Mtr of 7x7 Cable Chain with a start and end connector
M3 / M5 Bolts / Nuts (some M5 Nyloc Nuts) different lengths
Ferrules / Crimp connectors / Electronic Wires (use correct thickness)
GT2 6mm Belt (get a roll of 5 or 10 meter, not needed but you will have spare belt in case something goes wrong)
4 mm thick Plywood to make the electronics cabinet top and bottom (2 times 350x470mm)
Your preferred board. At the moment it is running on a Ramps 1.4 with standard stepper drivers and a graphical display.
Some Thick packaging Foam to use for sound / vibration dampening.
Handy to have:
Metric Drill Bits
Metric Hand Tap Threading Tools with corresponding drill bits
End stop connections used. (If you use X-Min you will have mirrored parts)
X-Max
Y-Min
Z-Min
Parts to print:
If you don't have the parts from https://www.thingiverse.com/thing:2668054
Go over there and get the following files to print.
X-carriage_Bridge_Motor_side
Cable_holder_V2_left_hand_side (2 times needed)
Cable_holder_V2_right_hand_side (2 times needed)
Bridge_Pulley_side
Y-Carriage_with_LM12UU
Y-Carriage_Belt_clamp (2 times needed)
E3D_clamp
New parts to print:
For the bed:
Z Axis Bearing Holder 1.0 (4 times needed)
Z T-Nut Bracket 1.0 (2 times needed) (If you plan to build it with a T8 leadscrew print those)
Z M8-Nut Bracket 1.0 (2 times needed) (If you plan to build it with a M8 leadscrew print those)
Z M8 Nut Blocker 1.0 (2 times needed) (If you plan to build it with a M8 leadscrew print those)
Mk2 Heat Bed Bracket 1.0 (4 times needed)
20 x 20 End Cap 1.0 (4 times needed)
For the frame:
20 x 20 Corner Bracing (3 way 90 degrees) 1.0 (8 times needed, buy or try to print)
Frame extender 1.0 (4 times needed)
Foot 1.0 (4 times needed)
Other parts:
X-Axis Bracket Front 1.0
X-Axis Bracket Front clamp 1.0
X-Axis Bracket Front motor 1.0
X-Axis Bracket Front motor clamp 1.0
X-Axis Bracket Back 1.0
X-Axis Bracket Back clamp 1.0
X-Axis Guide bracket 1.0
X-Axis Guide bracket clamp 1.0
Y-Axis Motor Bridge 1.0
Z-Axis Support Bottom (116mm) 1.0 (2 times needed)
Z-Axis Support Top (116mm) 1.0 (2 times needed)
Z_MIN switch holder 1.0
Bracket clamp 1.0 (3 times needed)
Motor bracket clamp 1.0
Belt Tensioner 1.0 (3 times needed)
Alignment of the Z-Axis Supports:
Use "X-Axis Bracket Front clamp 1.0" to align the Z-Axis support on top and bottom, alignment taken from the front of the printer with 0.5mm space between the bracket and Z-Axis supports. Align those parts first before placing the bottom box. You can flip the bracket 180 degrees to use on the right hand side.
Notes on the build:
Be sure that the Z-Axis rods have a snug fit in the Z-Axis supports.
All brackets that needs to be placed over the square extrusions of the frame, need to have a tight fit, though not need to be placed with the use of force.
For the print bed.
All brackets need to have a loose fit, but without any play
if your brackets for the heatbed have a snug fit, you can do the following trick to get them on a loose fit.
Slide the bracket over a piece of extrusion of about 100mm. This probably will need a bit of force to get them on, be sure that the bracket is about in the center of the extrusion.
Now get yourself a soldering iron and place it inside the extrusion and let it heat up.
Be patient and careful as the extrusion will get hot. Best is to use a towel to hold the extrusion when you start working on the bracket.
If the extrusion and the printed part reach the desired temperature, you will be able to start sliding the bracket over the extrusion.
Remove the soldering iron, switch it off and put it away on a safe spot.
Remove the bracket from the extrusion, let it cool down a bit, it will cool down faster then the extrusion, then place it back on the extrusion to slide it a few more times.
You should now have a loose fit without the need of using a file or sanding.
If you need to apply to much force to get the bracket on the extrusion, file it down first as it will not work with the above trick.
When assembling the bed frame, as shown on the first picture of the printer, the Mk2 Heat Bed Bracket 1.0 needs to be mounted at a 9.2mm distance from the Z Axis Bearing Holder 1.0. On the side where the Dual axis NEMA sits.
WARNING when you start printing:
Do NOT forget to switch on your cooling, else you will end up with a clogged extruder / overheated board.
Disclaimer:
3D_PP is not responsible for any damage / injuries what so ever in any kind of degree.
Building this printer is all at your own risk, as it is with all other builds you create.
Always shut down the Main Voltage Input when working on Electronic Components.
Know what you are doing, You are working with High Voltages and high temperatures.
Take NO Risks <<<
If you like our work, consider to make a small donation so we can keep on developing.
If you made one, please share a picture of your design.
Similar models
thingiverse
free
Prusa i3 Y Axis Bearing Rod Support by henryarnold
...mm cap screw and nut for the clamp. you'll also need the captive nut used with the extrusion which came with the printer kit.
thingiverse
free
Quad Rod CoreXY 3D Printer by MakersMic
...to the list of files.
parts list will be updated regularly to alleviate any discrepancies.
thanks for viewing and happy printing.
thingiverse
free
Refil 3D Mini Beast V1.1 Upgrades by refil3d
...me to comment below or join our facebook group https://www.facebook.com/groups/641612192699533/ and contribute to the discussion!
thingiverse
free
PrintrMatic 3D printer by thehair
...astruder)
pancake stepper nema 17 20mm (stepperonline)
other
various m3 and m4 bolts
m3 brass inserts used on all printed parts.
thingiverse
free
Printer base clamp and z-axis squaring mount by Westdale3D
...lamp (2 at either end of the y-axis). then the two square mount for z-axis pieces could be fastened the the platform and printer.
thingiverse
free
Tinkering the Ivan Miranda Big Printer to a smaller version (Completed) by 3D_PP
... off-course post them.
3dpp wish all the people that are building or planning on building this printer "happy printing"
thingiverse
free
Aluminium Extrusion Frame by ctheroux
...djustable foot available at http://www.thingiverse.com/thing:2250225
ivan miranda (http://ivanmiranda.com/) inspired this design.
thingiverse
free
Junior 1.0 linear bearing in the Z-right rod by sicicop
...ar bearing.
to hold the bearing is needed 4 m3x10mm screws and 4 nuts. also need 2 m3x8mm screws to attach in the x axis carriage
thingiverse
free
Smartcore Double Z Screw for Oilless Bushings by smerrett79
...s rod on the sides of the smartcore box frame.
you need to print two of each of the three parts to make a double z screw printer.
thingiverse
free
Refil 3D Mini Beast by refil3d
...!) £59
10 x f623zz flange ball bearing shielded 3 x 10 x 4mm £18
facebook group: https://www.facebook.com/groups/641612192699533/
Hum
turbosquid
$25
Hum Vee
...ee
turbosquid
royalty free 3d model hum vee for download as on turbosquid: 3d models for games, architecture, videos. (1246450)
3d_ocean
$5
Humming Bird
...rmats include an .ma, .mb, .obj, .fbx verts – 2530 faces – 2522 check out my other products, just click on my user name to see...
turbosquid
$3
HUM BIRD
...free 3d model hum bird for download as max, 3ds, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1672290)
turbosquid
$45
HUMMING BIRDS.MAX
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$30
Humming bird 3D Model
...l
3dexport
animal bird flying green humming hummingbird tropical wild wing kolibri
humming bird 3d model rmilushev 71438 3dexport
3d_export
$35
Humming bird
... zbrush 3ds max ztool obj fbx dae 3ds stl properties : 20*20*16 production time : 12 hours 161 gram models are drawn with zbrush.
turbosquid
free
ts mod hum
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
Hen and Humming bird Egg
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$29
humming bird pbr rigged low poly
...humming bird pbr rigged low poly
3dexport
3d_export
$5
spider ham
...ham 3dexport mighty muggs fan art of the spider hum to use it wherever you...
Sneak
turbosquid
$24
Beer Can 21st Amendment Sneak Attack 12fl oz
...r can 21st amendment sneak attack 12fl oz for download as max on turbosquid: 3d models for games, architecture, videos. (1178999)
3d_ocean
$30
Bedroom furniture 05
...table, chest of drawers, shelves, jewerly box, lamp, pictures, sneak... ...
3d_export
$5
spaceship bubble
...capsule with a glass-like material all around gives a sneak peak at the minimalistic seat, in front of which...
3d_export
$149
white american bald eagle
...look around<br>jump forward start<br>jump left<br>jump right<br>jump back<br>jump attack<br>sneak forward<br>sneak right<br>sneak left<br>sneak back<br>walk attack<br>walk jump start right foot<br>walk jump start...
3d_export
$129
star wars at-st walker rigged
...often flanking approaching at-ats and mopping up infantry that sneak past the larger walkers. the imperials used at-sts in...
thingiverse
free
sneaking thief
...sneaking thief
thingiverse
sneaking halfling thief
thingiverse
free
sneak-it by colin721
...sneak-it by colin721
thingiverse
support chaussure
sketchfab
$4
Day 4 - Sneaking Insect
...za.
here is a insect that can hidde in tree´s
@sculptjanuary - day 4 - sneaking insect - buy royalty free 3d model by 3dguimaraes
thingiverse
free
Sneak drinkcoaster by RaimonElctrncs
... (100 by 100 by 5 mm), to fit in my coasterholder:
https://www.thingiverse.com/thing:3130397
made with love by:
raimon of idealab
thingiverse
free
Sneak Attack! Logo by EllenTheEmu
...a 3d model of the sneak attack logo that i made in tinkercad. feel free to edit it/ use it for whatever you want (within reason).
Pp
3ddd
$1
PP 240 chair
...pp , 240 , pp mobler
стул pp240 фирмы pp mobler
design_connected
$16
PP 501-503
...pp 501-503
designconnected
pp mobler pp 501-503 computer generated 3d model. designed by wegner, hans.
turbosquid
$25
PP-502
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$8
PP Vase
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$11
PP 85 Tondern Table
... tondern table
designconnected
pp mobler pp 85 tondern table dining tables computer generated 3d model. designed by hans wegner.
turbosquid
$79
Walther PP 01 a
...ee 3d model walther pp 01 a for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1542938)
turbosquid
$35
PP-91 KEDR
...ty free 3d model pp-91 kedr for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1272160)
3d_export
$49
Audi PP Quattro 3D Model
...audi pp quattro 3d model
3dexport
audi pp quattro car vehical transportation
audi pp quattro 3d model mpavlos 9772 3dexport
turbosquid
$15
PP-91 Kedr
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
Walther PP pistol
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
V1
turbosquid
$35
v1
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
street tree v1
...street tree v1
3dexport
street tree v1
3d_export
$5
potato v1
...potato v1
3dexport
turbosquid
$20
Kitchen V1
...bosquid
royalty free 3d model kitchen v1 for download as max on turbosquid: 3d models for games, architecture, videos. (1153622)
turbosquid
$12
sofa v1
...turbosquid
royalty free 3d model sofa v1 for download as max on turbosquid: 3d models for games, architecture, videos. (1283267)
turbosquid
$3
Chair V1
...urbosquid
royalty free 3d model chair v1 for download as fbx on turbosquid: 3d models for games, architecture, videos. (1486093)
turbosquid
$15
Cupboard v1
...royalty free 3d model cupboard v1 for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1444568)
3d_export
$5
tram v1
...tram v1
3dexport
3d_export
$8
lumber car v1
...lumber car v1
3dexport
lumber car v1 printable, low poly model.
turbosquid
$20
DELTALIGHT v1
...free 3d model deltalight v1 for download as max, max, and obj on turbosquid: 3d models for games, architecture, videos. (1630928)
Prototype
3ddd
$1
iphone (prototype)
...e (prototype)
3ddd
iphone prototype телефон сотовый прототип , iphone
iphone (prototype)
turbosquid
$60
prototype
...y free 3d model prototype for download as , fbx, stl, and obj on turbosquid: 3d models for games, architecture, videos. (1516333)
turbosquid
free
prototype
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Prototype Crossbow
...squid
free 3d model prototype crossbow for download as blend on turbosquid: 3d models for games, architecture, videos. (1237541)
turbosquid
$25
Atlas Prototype
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Prototype Airplane
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
starship prototype
...y manufactured in boca chica ,texas by spacex. this prototype consist features like forward flaps, bottom flaps and landing legs.
design_connected
$11
Jellyfish Chandelier (prototype)
...sakai design associate jellyfish chandelier (prototype) pendant lights computer generated 3d model. designed by toshihiko sakai.
turbosquid
free
Prototype Plasma Rifle
...d
free 3d model prototype plasma rifle for download as blend on turbosquid: 3d models for games, architecture, videos. (1237576)
turbosquid
$15
Prototype CNC Router
... model prototype cnc router for download as iam, ige, and stl on turbosquid: 3d models for games, architecture, videos. (1667298)
V2
3d_export
free
Lamp v2
...lamp v2
3dexport
lamp v2 with solar panel
3d_export
$5
hammerhead v2
...hammerhead v2
3dexport
razer hammerhead v2 headphones, modeled in cinema 4d, render in corona
3d_export
$5
manometer v2
...manometer v2
3dexport
3d_export
$5
potato v2
...potato v2
3dexport
turbosquid
$52
Lifebuoys v2
...squid
royalty free 3d model lifebuoys v2 for download as fbx on turbosquid: 3d models for games, architecture, videos. (1560870)
turbosquid
$2
Mask v2
...turbosquid
royalty free 3d model mask v2 for download as stl on turbosquid: 3d models for games, architecture, videos. (1527741)
turbosquid
free
Flashlight V2
...d
free 3d model flashlight v2 for download as , obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1663559)
turbosquid
$29
Thanos v2
...
royalty free 3d model thanos v2 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1651077)
turbosquid
$29
Titan v2
...d
royalty free 3d model titan v2 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1540228)
turbosquid
$29
Frieza v2
...
royalty free 3d model frieza v2 for download as ztl and obj on turbosquid: 3d models for games, architecture, videos. (1701238)
Final
3ddd
$1
Ardecora-Finale
...ardecora-finale
3ddd
ardecora
ткань итальянского производителя ardecora, артикул finale. в архиве 7 цветов. ткань портьерная.
turbosquid
$3
Wheel Final
...osquid
royalty free 3d model wheel final for download as fbx on turbosquid: 3d models for games, architecture, videos. (1364402)
turbosquid
free
Final Sword
...osquid
royalty free 3d model final sword for download as max on turbosquid: 3d models for games, architecture, videos. (1428573)
turbosquid
$16
Yeti final
...lty free 3d model yeti final for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1374065)
turbosquid
$180
moto final
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$80
final cowboy.max
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$36
Final UZI
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
Gumout Final
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
money finals
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
guitar final
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
0
turbosquid
$12
Calligraphic Digit 0 Number 0
...hic digit 0 number 0 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389318)
3d_export
$6
set-0
...set-0
3dexport
turbosquid
$6
hedge 0
...yalty free 3d model hedge 0 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1450353)
turbosquid
$5
Nuber 0
...oyalty free 3d model nuber 0 for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1564674)
turbosquid
$22
0.jpg
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Steam Locomotive Fowler 4F 0-6-0
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Liquid Number 0
... model liquid number 0 for download as c4d, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1689919)
turbosquid
$45
Dragon360_perspShape_tmp.0.jpg
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$8
Rocks Debris 0
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$18
wood-guardrail-fence 0
...wood-guardrail-fence 0
3dexport
wood-guardrail-fence 0<br>3ds max 2015
Completed
turbosquid
$35
complete plan
...quid
royalty free 3d model complete plan for download as max on turbosquid: 3d models for games, architecture, videos. (1221693)
turbosquid
$10
COMPLETE WASHROOM
...
royalty free 3d model complete washroom for download as max on turbosquid: 3d models for games, architecture, videos. (1413853)
turbosquid
$1
Complete Office
...id
royalty free 3d model complete office for download as max on turbosquid: 3d models for games, architecture, videos. (1323641)
vizpark
$509
VP COMPLETE
...e is the ultimate collection of 3d archviz assets, including 900 3d models, 50 hdris, 100 tileable textures and pattern software.
turbosquid
$15
excercise complete
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
complete cabinet
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
complete Desk.lwo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Complete Wall Pack
...complete wall pack
3dexport
a complete set of 14 walls
3d_ocean
$12
Complete Model
... any other purpose. model includes, tree, street light, bench with urn, horse model. total poly and verts are 282,036 and 334,...
turbosquid
$80
sasuke complete susanoo
...oyalty free 3d model sasuke complete susanoo for download as on turbosquid: 3d models for games, architecture, videos. (1693376)
Preview
turbosquid
free
Material Preview Object
...l material preview object for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1207378)
turbosquid
free
Construction Objects Preview
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Industrial Objects Preview
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Ready Scene Preview
... model product turntable for download as ma, ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1538357)
turbosquid
free
Preview Living Room French Style
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
jers spiked robots 3ds pieces with previews
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
.45 ACP Low Polygon Preview Model
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Realistic Basemesh - Free Sample Preview - all models
...ew - all models for download as obj, fbx, blend, dae, and stl on turbosquid: 3d models for games, architecture, videos. (1425441)
3d_export
free
Download free Mr Preview Bedroom 3D Model
...rchitecture mentalray chair desk computer television tv real realistic
mr preview bedroom 3d model andrej.persolja 96624 3dexport
turbosquid
free
Realistic Human Basemesh - Male and Female - Free Sample Preview
... sample preview for download as obj, fbx, blend, dae, and stl on turbosquid: 3d models for games, architecture, videos. (1425443)
Box
archibase_planet
free
Box
...box
archibase planet
box carton cardboard box
box 2 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Box
...box
archibase planet
carton cardboard box box
box 1 - 3d model (*.3ds) for interior 3d visualization.
3d_export
$6
box
...box
3dexport
box
3d_export
$5
Box
...box
3dexport
box
3d_export
$5
box
...box
3dexport
box
3d_export
$5
box
...box
3dexport
box
archibase_planet
free
Box
...box
archibase planet
box box for paper notebook pencil
box - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Box
...box
archibase planet
box carton cardboard box
box n170111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Box
...box
archibase planet
box carton cardboard box
box n050411 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Boxes
...boxes
archibase planet
boxes box case bin
boxes n281213 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
Working
3d_export
$5
WORKING PLATFORM
...working platform
3dexport
working platform 4000x3000x1500mm
design_connected
$16
Working set
...working set
designconnected
smallaccents working set computer generated 3d model.
3ddd
free
Pinao / Stelar Works
...pinao / stelar works
3ddd
stelar works , stellar works
стулья pinao от stelar works
design_connected
$13
Work Lamp
...work lamp
designconnected
design house stockholm work lamp computer generated 3d model. designed by form us with love.
turbosquid
$6
Road Works
...turbosquid
royalty free 3d model road works for download as on turbosquid: 3d models for games, architecture, videos. (1151328)
3ddd
free
Stellar Works Lumar
...llar works , lumar , барный
stellar works lumar
turbosquid
$20
Work boots
...bosquid
royalty free 3d model work boots for download as stl on turbosquid: 3d models for games, architecture, videos. (1313566)
turbosquid
$8
Desk Work
...osquid
royalty free 3d model desk work for download as blend on turbosquid: 3d models for games, architecture, videos. (1381338)
turbosquid
$5
Work Desk
...osquid
royalty free 3d model work desk for download as blend on turbosquid: 3d models for games, architecture, videos. (1435344)
turbosquid
$1
Plant for work
...uid
royalty free 3d model plant for work for download as obj on turbosquid: 3d models for games, architecture, videos. (1557514)