Thingiverse
The Beest by EvenErichsen
by Thingiverse
Last crawled date: 3 years ago
This is a working hand cranked power generator.
The rotor, in the picture, spins up to 1500 rpm, and produce about 30 watts.
I recommend building the rotor as seen in the fbx-file, for more power.
Needless to say – this is a huge print! Minimum 200+ hours....
On the hardware side you need 96 neodymium magnets (25mm diameter x 10mm),
about 1,3kg of enameled copper wire, preferably six steel plates, a pile of nuts & bolts, electronics - including an Arduino nano, display, bridge rectifier(s), diodes, capacitors, resistors, voltage regulators etc.
If you want to etch the PCB yourself, you will need a blank 160mm x 100mm copper board and your preferred chemicals.
Real-time model:http://www.justpressprint.no/3d-models/generator-v2/
Video:https://youtu.be/Z4HIWI0tqTk
Until I release a set of instructions, consider this a work of art ;)
The rotor, in the picture, spins up to 1500 rpm, and produce about 30 watts.
I recommend building the rotor as seen in the fbx-file, for more power.
Needless to say – this is a huge print! Minimum 200+ hours....
On the hardware side you need 96 neodymium magnets (25mm diameter x 10mm),
about 1,3kg of enameled copper wire, preferably six steel plates, a pile of nuts & bolts, electronics - including an Arduino nano, display, bridge rectifier(s), diodes, capacitors, resistors, voltage regulators etc.
If you want to etch the PCB yourself, you will need a blank 160mm x 100mm copper board and your preferred chemicals.
Real-time model:http://www.justpressprint.no/3d-models/generator-v2/
Video:https://youtu.be/Z4HIWI0tqTk
Until I release a set of instructions, consider this a work of art ;)
Similar models
thingiverse
free
The Hand Cranked Power Generator by EvenErichsen
...s close to 15 watts...
instructions will follow later..
use the attached 3d studio max-file to see finished assembly for now.
grabcad
free
Small VAWT vertical axis wind turbine C-rotor for 3D Printing
...r 48v
2 ball bearings
one nut and screw
power of this generator depends on what magnets and wires will you use.
enjoy testing :)
3dwarehouse
free
Small VAWT C-rotor type wind turbine for 3D printing
...what magnets and wires will you use. enjoy testing :) #3d_printable #crotor #small_wind_turbine #vawt #vertical_axis_wind_turbine
grabcad
free
MINI DIESEL GENERATOR CAD MODEL
...tor within the magnetic field produced by the stator induces an electrical current in the stator windings, producing electricity.
3dwarehouse
free
Wind Power Generator Rotor
...wind power generator rotor
3dwarehouse
thingiverse
free
Large Turbine Generator Model by Jedi_Craig
...he rotor on the collector housing slip rings. only the rotor needed printing support.
model is 2mm scale, very close to n scale.
grabcad
free
Variable Pitch Rotor
...variable pitch rotor
grabcad
wind power generator
grabcad
free
800mm Rotor Blade
... generic rotor blade for a helicopter head i was designing. i needed a blade to get good reference for over size, and clearances.
cg_trader
free
Variable Pitch Rotor
...variable pitch rotor
cg trader
wind power generator
grabcad
free
Copper Rotor
...copper rotor
grabcad
induction motor rotor
Evenerichsen
thingiverse
free
Kinect Grip by EvenErichsen
...ect sensor bar, which also can be used as a 3d-scanner.
it is adjustable, and ie. lets you easily scan stuff low to the ground.
thingiverse
free
Bulb Light by EvenErichsen
... add some weight.
also a canal for wiring(may be a bit tricky to get through).
the bulb is cut in two pieces and has to be glued.
thingiverse
free
Chocolate Milk Mixer by EvenErichsen
...t chocolate milk!
the stl has a footprint of 8,1 x 5,7 cm. the height is 13,5 cm.
you could of course scale it to your needs ;)
thingiverse
free
Shopping Bag Handle by EvenErichsen
...ich uses multiple photos taken from a slightly different angle to generate a 3d-mesh.
left and right grip.
no support needed.
thingiverse
free
DNA Helix by EvenErichsen
...ly be rearranged to fit your printer.
i used a 600 x 5 mm metal rod to slide the pieces over, it helps to keep it all together.
thingiverse
free
The Hand Cranked Power Generator by EvenErichsen
...s close to 15 watts...
instructions will follow later..
use the attached 3d studio max-file to see finished assembly for now.
Beest
thingiverse
free
The Beest - A Strandbeest Walker by fhareide
...nt for the legs measurement ratio as this is crucial for a smooth walk. i then started modelling the motor to exact measurements.
thingiverse
free
Beest with Gripper (Robert) by RazilBen
...troller and stop, maybe even back up couple steps will see
all printed with petg on anycubic mega x - no postprocessing required
grabcad
free
Theo Jansen Walking Beest
...theo jansen walking beest
grabcad
another walking mechanism.
cg_trader
$5
This is low poly 3d model of wild beest
...this is low poly 3d model of wild beest
cg trader
cg_trader
$15
Blender Monkey
...other characters. all textures are hand painted and work beest with shadles materials and outlines. textures are...
3dwarehouse
free
Beesting Alpha Minicar
... with 50 cal. auto's and a spiked bumper. please rate! #alpha_minicar #alpha_motorcars #beesting_minicar #minicar #mojomodels
3dwarehouse
free
giesbeek huis
...giesbeek huis 3dwarehouse beest wel...
3dwarehouse
free
giesbeek huis
...giesbeek huis 3dwarehouse beest wel...
3dwarehouse
free
hond
...hond 3dwarehouse een 3d hond #3d #3d_hond #beest #dier...