Thingiverse
Terminal Block by bobnojio
by Thingiverse
Last crawled date: 3 years ago
a single-row terminal block for wiring.
requires nuts and bolts.
Im using a few of these to replace blade connectors in my vehicle, and a few for home projects as well.
Future:
if I have time, I might see if I can recess the nuts into the bottom of the part, so that it could be mounted flat onto a surface.
requires nuts and bolts.
Im using a few of these to replace blade connectors in my vehicle, and a few for home projects as well.
Future:
if I have time, I might see if I can recess the nuts into the bottom of the part, so that it could be mounted flat onto a surface.
Similar models
thingiverse
free
Motorcycle Battery Terminal Block - Nut Housing by 3P3D
...erminal.
print and install as shown in the pictures. this may need to be scaled to fit your specific nut and battery terminal.
thingiverse
free
Terminal block for M3 screw by t_colon
...se of 4p terminal block.
conclusion of contact points:
m3-10 screw
(wire or crimping terminal)
m3 washer
base
lag terminal
m3 nut
thingiverse
free
P10 Terminal Block Mount by ShinyObjects
...d of some screws are just slightly too big to fit in the upper part of the hole. i ended up using a #8 socket cap screw instead.
thingiverse
free
Terminal Strip - with recessed nuts by bobnojio
...oesnt have to be pretty!
note: ignore the pictures... i have recessed the nuts on this version! (reused pictures of previous)
3dwarehouse
free
Terminal Block
...terminal block
3dwarehouse
molex terminal block #block #electrical #terminal #wiring
grabcad
free
Terminal Blocks
...terminal blocks
grabcad
terminal blocks - barier blocks
thingiverse
free
Terminal Block by mustardkeenas
...down by an m3 bolt into a hex nut similary embedded into the bottom of the...
cg_trader
$20
electrical terminal block
...electrical terminal block
cg trader
electrical terminal block with terminals and ground terminals
grabcad
free
Terminal block
...terminal block
grabcad
terminal block
grabcad
free
Terminal block
...terminal block
grabcad
terminal block
Bobnojio
thingiverse
free
Button replacement for coat - beveled edges by bobnojio
...obnojio
thingiverse
i needed a button, so i made a button. and i beveled off the edges so that it wont cut my thread as easily.
thingiverse
free
Clash of Clans Bomb model by bobnojio
...and corrected the file. the original was slicing without the center sphere, and prints correctly after being run through netfab.
thingiverse
free
Vladimir Putin bust - no tie by bobnojio
...fter a lot of searching, i found a lot of high res 3d scans of putin, so i sculpted this one.
enjoy!
and please, tip me a coffee!
thingiverse
free
Rigidbot external PSU Mount by bobnojio
... loosen a side panel, or cut a hole in one to get it to be pretty.
printing my first one now. will add a make once it is done.
thingiverse
free
Terminal Strip - with recessed nuts by bobnojio
...oesnt have to be pretty!
note: ignore the pictures... i have recessed the nuts on this version! (reused pictures of previous)
thingiverse
free
Rigidbot tool caddy by bobnojio
...holes work quite well for allan keys.
caliper fits nicely.
added a v2 file -- wider hole for feeler gauge, wider hole for lube.
thingiverse
free
LED BusyLamp holder/stand by bobnojio
...d and resistor, sitting on top of my desk / cubicle wall
so that walk-up people can see im on the phone, before they interrupt me
thingiverse
free
Magnetic Phone Mount for Gym equipment by bobnojio
......)
v2 - wider hole for phone
slightly thinner band, hopefully more flex
smaller nubs to grab phone
better rounded back corner
thingiverse
free
RigidBot Tool Caddy by webdes03
...tweezers, straight tweezers, and two allen wrenches. inspired by bobnojio#39;s original rigidbot tool caddy, this version has been adapted...
Terminal
archibase_planet
free
Terminal
...planet
terminal payment terminal
terminal internet terminal point n140815 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...nal
archibase planet
payment terminal terminal equipment
terminal n190111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
terminator
...terminator
3dexport
terminator. for 3d print.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal
terminal 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal
terminal 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal
terminal 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal
terminal 4 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal equipment
terminal n181210 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal equipment
terminal n070211 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Terminal
...terminal
archibase planet
terminal rack post
fp terminal wh - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Block
archibase_planet
free
Blocks
...blocks
archibase planet
blocks bricks toy
toy blocks - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
Block
...block
3dexport
3d_export
$10
The guillotine and the block
...the guillotine and the block
3dexport
the guillotine and the block autocad 2013
3d_ocean
$8
Concrete Blocks
... blocks, barriers or cover for characters during a fire fight. each one has its own diffuse map, specular and normal map in tg...
archibase_planet
free
Glass block
...glass block
archibase planet
glass block brick
glass block n211009 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$99
city block
...city block
3dexport
city block 3d model. include max, obj and fbx files.
3d_ocean
$3
Concrete Blocks Textures
...res
3docean
block blocks concrete seamless wall walls
a couple of seamless textures with two differents sizes of concrete blocks.
3d_export
$5
plummer block
...plummer block
3dexport
this is an 3d model of plummer block assembly where seven parts are required to assemble this.
design_connected
$16
Block 2
...block 2
designconnected
henry pilcher block 2 computer generated 3d model. designed by pilcher, henry.
3d_export
$7
concrete blocks on pallets
...concrete blocks on pallets
3dexport
concrete blocks on pallets, 3 types of blocks. there are all the necessary textures.