Thingiverse
Sunlu Filament Dryer Hanging Spool Roller by Chambeers
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a top mount spool hanger I made for the Sunlu Filament Dryer. I was having issues with the stock roller placement, the spool would turn a little sideways and bind up and jump around a little. This eventually caused a 48 hour print to fail with the expensive CarbonX Nylon so I decided to make these.
No hardware or tools required this relocates the Sunlu rollers and bearings that come with the dryer.
Step 1: Carefully remove the factory rollers with the bearings one side at a time. There is plenty of room to do this without ripping the insulation or breaking the pocket they fit into.
Step 2: Pull the bearings off and put a small drop of superglue on the roller shafts that go inside the bearing, then reassemble the roller and bearings back together.
Step 3: Insert the printed parts from the file with the circles where the bearings used to be.
Step 4: Lower your filament spool into the dryer with only one of the rollers in the hole of the spool at first (lines up much easier than trying to do both rollers at the same time) then do the other while the spool is hanging.
The spool will wobble a bit until the lid is shut but the bearings make contact with the lid for excellent support.
If using PLA I'd recommend printing with 100% infill to avoid any issues at max dryer temperatures. I printed all of mine with CarbonX Nylon that I had left on the spool at 20% infill.
No hardware or tools required this relocates the Sunlu rollers and bearings that come with the dryer.
Step 1: Carefully remove the factory rollers with the bearings one side at a time. There is plenty of room to do this without ripping the insulation or breaking the pocket they fit into.
Step 2: Pull the bearings off and put a small drop of superglue on the roller shafts that go inside the bearing, then reassemble the roller and bearings back together.
Step 3: Insert the printed parts from the file with the circles where the bearings used to be.
Step 4: Lower your filament spool into the dryer with only one of the rollers in the hole of the spool at first (lines up much easier than trying to do both rollers at the same time) then do the other while the spool is hanging.
The spool will wobble a bit until the lid is shut but the bearings make contact with the lid for excellent support.
If using PLA I'd recommend printing with 100% infill to avoid any issues at max dryer temperatures. I printed all of mine with CarbonX Nylon that I had left on the spool at 20% infill.
Similar models
thingiverse
free
Sunlu Filament Dryer Spool Roller Support by kinyas01
...egs was not vertical and stable. i designed a part in order to keep vertical and stable to legs.
you can print it as 100% infill.
thingiverse
free
Filament Dryer / Dehydrator spool roller / spool holder by Petclaud
...to insert the 608 bearing in the roller. make sure the bearing is flush at the top of the hole of the filament roller base plate.
thingiverse
free
Sunlu Filiment Dryer Mount for Wanhao i3 or Similar clone by Chambeers
...lds the sunlu dryer in place while allowing the dryer to be easily lifted up and out for cleaning, maintenance, or spool changes.
thingiverse
free
SUNLU Filament Dryer Top PTFE Connector by Sledhead92
...tside to connect the bowden tube which i run to my hot end.
i printed with standard (good) settings in cura for my ender 5 pro.
thingiverse
free
Filament Spool Roller Small half roll - Snap Fit 6x19x6mm Bearings 626zz by TyCreek
...oot to make a filament roller pair. the 626 bearings have a 6mm hole and are 6mm wide by 19mm outside diameter (size of a penny).
thingiverse
free
Filament Spool Roller (v2) for 70mm and 120mm Spools by marcope82
...e82
thingiverse
a simple filament spool roller for spools up to 70mm.
i used 608zz skateboard bearings from amazon.
have fun! :)
thingiverse
free
Spool Roller
... i didn't already have kicking around; ergo, i designed my own.
parts required to complete:
4 m6 x 16mm screws
4 626 bearings
thingiverse
free
Rob's CarbonX X-Frame Whoop by robthomson
...a ducted whoop - then the e010s frame or similar is hard to beat! i print with carbonx nylon...
thingiverse
free
Rob's CarbonX Deadcat-Frame Whoop by robthomson
...a ducted whoop - then the e010s frame or similar is hard to beat! i print with carbonx nylon...
thingiverse
free
Filament Spool Hub with Print In Place Bearings by BoomZilla1
...rom 3d mars and the hole was bigger. use the original hubs for spools up to around 54mm and the large version for ones up to 57mm
Sunlu
thingiverse
free
box sunlu by cncbuster
...box sunlu by cncbuster
thingiverse
sunlu dryer box filament
thingiverse
free
Filament Clip (for Sunlu) by lucarossetti
...filament clip (for sunlu) by lucarossetti
thingiverse
this is a filament clip for sunlu filament
thingiverse
free
Sunlu direct extruder by masbytes
...sunlu direct extruder by masbytes
thingiverse
adapter for direct extruder for sunlu s8
thingiverse
free
sunlu centric spool holder
...of the spool, for sunlu filaments and sunlu s8 spool holder. the diameter inside is 20mm an de out side is 71,5. its fits perfect
thingiverse
free
Filament Holder SUNLU Filament by TrisiT
...filament holder sunlu filament by trisit
thingiverse
remix for the sunlu filament rolls.
thingiverse
free
Sunlu Spool Holder
...ng:1241566
holder is 90mm wide to accommodate the larger inner diameter sunlu spools
this is tested on sulu pla & petg spools
thingiverse
free
SUNLU S8 Z-Endstop
...sunlu s8 z-endstop
thingiverse
i designed a quick and dirty solution for the horrable original z endstop holder of the sunlu s8
thingiverse
free
Smooth Fang Mount Sunlu S8
...smooth fang mount sunlu s8
thingiverse
smooth fang mount to sunlu s8 printer
thingiverse
free
SUNLU S8 Fan Duct by CalebC90
...sunlu s8 fan duct by calebc90
thingiverse
sunlu s8 fan duct and part cooling duct.
thingiverse
free
SUNLU FILAMENT by umitakin
...sunlu filament by umitakin
thingiverse
filament makarasını tutmak için hazırlanmıştır.
Dryer
thingiverse
free
Towel Dryer
...towel dryer
thingiverse
towel dryer
thingiverse
free
pasta dryer
...pasta dryer
thingiverse
pasta dryer. no support needed to print.
thingiverse
free
Dryer latch by baberlevi
...dryer latch by baberlevi
thingiverse
improved dryer latch for frigidaire affinity dryer
thingiverse
free
Pasta Dryer
...pasta dryer
thingiverse
pasta dryer for long-medium length pastas or noddles. enjoy!
thingiverse
free
Telescope dryer
...telescope dryer
thingiverse
you need just a feew bags of silika gel dryer
thingiverse
free
Holder dryer by baksser
...holder dryer by baksser
thingiverse
holder dryer
thingiverse
free
WETSUIT DRYER by qba1
...wetsuit dryer by qba1
thingiverse
wetsuit dryer
thingiverse
free
Dryer Dial by mgl1998
...dryer dial by mgl1998
thingiverse
universal dryer dial. use as replacement of your broken or no working dial for your dryer.
thingiverse
free
Sock Dryer by Liang0108
...sock dryer by liang0108
thingiverse
sock dryer model.
thingiverse
free
Cup Dryer by Firnas
...rse
cup dryer ? ???
?? ?? ? ?? ?? ??? ?? ?? ?? ??
? ??? 2? ?????.
? ???? ???? ?? ? ?? ??????
??? ?? ????? ?? ?? ???? ?? ?? ????,
Roller
thingiverse
free
Roller
...roller
thingiverse
roller for a 75mm tape gun.
thingiverse
free
Rollers on Track Rollers
...physics exercise "roller's on track". i won't link to the exercises as this will short-circuit some learning.
thingiverse
free
roller by Warwick3D
...roller by warwick3d
thingiverse
roller
thingiverse
free
roller by justinbarrera14
...roller by justinbarrera14
thingiverse
roller
thingiverse
free
Roller by shvanmajd
...roller by shvanmajd
thingiverse
roller
thingiverse
free
roller by justinbarrera14
...roller by justinbarrera14
thingiverse
roller 1
thingiverse
free
Roller by sekom
...roller by sekom
thingiverse
roller toy
thingiverse
free
lint roller
...lint roller
thingiverse
for sticky lint rollers
thingiverse
free
roller cookie
...roller cookie
thingiverse
roller cokie form
thingiverse
free
fidget roller
... in your hand
print the caps once and the rollers twice
i recommend printing the lids on 100% infill and the rollers on about 10%
Hanging
thingiverse
free
Hanged
...hanged
thingiverse
a hanged.
you can support me on https://www.patreon.com/schlossbauer if you like my work.
thingiverse
free
Hanging hook
...hanging hook
thingiverse
bathroom hanging hook
thingiverse
free
hanging by cerapersa
...hanging by cerapersa
thingiverse
hanging towel radiator
thingiverse
free
for hanging by yoyoek1
...for hanging by yoyoek1
thingiverse
i use it for hanging a backpack.
thingiverse
free
Hanging Basket
...hanging basket
thingiverse
made a thing that could be attached to some rope to hang something with it.
thingiverse
free
hanging bracket by DBosch
...hanging bracket by dbosch
thingiverse
hanging bracket
thingiverse
free
Hanging bridge by BlackConcept
...hanging bridge by blackconcept
thingiverse
a model of a hanging bridge
thingiverse
free
Hanging hook by jzprice1
...hanging hook by jzprice1
thingiverse
hook to hang things with
thingiverse
free
Hang glider by Kachalot
...hang glider by kachalot
thingiverse
a little hang-glider
thingiverse
free
hanging scale by Yoctopuce
...you can find more infromation on this hanging scale in our blog:https://www.yoctopuce.com/en/article/implementing-a-hanging-scale
Spool
thingiverse
free
Spool Support For Anycubic Spool Holder and AMZ3D Spools by Kobaratsu
... amz3d spools by kobaratsu
thingiverse
spool axis support to avoid jerks on spool, using anycubic spool holder and amz3d spools
thingiverse
free
Spool adapter for Warhorse spool
...spool adapter for warhorse spool
thingiverse
a simple spool adapter to use abs warhorse spool with a 72 mm hole diameter.
thingiverse
free
Spool holder for 1KG Spools by angkor
...spool holder for 1kg spools by angkor
thingiverse
spool holder for 1kg spools
thingiverse
free
Spool holder
...spool holder
thingiverse
i use this spool holder for up to 1kg spools and should fit all spools.
thingiverse
free
Spool assembler
... empty spool with this spool assembler
just cut an empty spool in half , put your filament and assemble with this spool assembler
thingiverse
free
Small Spool and Spool Stand by Beckman13
...ool holder are meant for 50 gram flexible filaments. the two sides of the spool holder are meant to slide together and interlock.
thingiverse
free
spool spindle cap for 25mm spools by Seadevil
...spool spindle cap for 25mm spools by seadevil
thingiverse
spool spindle cap for 25mm spools
thingiverse
free
spool ! by St0rmingBr4in
...spool ! by st0rmingbr4in
thingiverse
this is a spool !
thingiverse
free
Spool Holder for large spools by dmonkey
...y
thingiverse
a spool holder that you can attach to the back of a makerbot replicator that can hold large filament spools (1kg)
thingiverse
free
Spool roll
...spool roll
thingiverse
spool roll
Filament
thingiverse
free
Filament holder for 1,75mm filament by Boschlike
...ent holder for 1,75mm filament by boschlike
thingiverse
filament holder for 1,75mm filament.
mountable on the prusa mk3s+ frame.
thingiverse
free
Filament Holder SUNLU Filament by TrisiT
...filament holder sunlu filament by trisit
thingiverse
remix for the sunlu filament rolls.
thingiverse
free
Filament stand
...filament stand
thingiverse
basic filament stand for filament coils with bigger diameter.
thingiverse
free
Filament Holder
...filament holder
thingiverse
this filament stand is to hold the filament without using the as-built location
thingiverse
free
Filament clip
... clip
really easy to print and use. no hole to insert the filament. the filament stay in place because pressed against the spool.
thingiverse
free
Filament hanger
...filament hanger
thingiverse
hanger for filaments. it helps you organize your filaments and work space.
thingiverse
free
filament holder
...filament holder
thingiverse
filament holder
thingiverse
free
Filament Cradle
...filament cradle
thingiverse
filament cradle
thingiverse
free
Filament Holder (Filament Spool) by herenkeskin
...filament holder (filament spool) by herenkeskin
thingiverse
this is a filament holder. i printed this part on my tevo tarantula.
thingiverse
free
Pyramid Filament Mount with Filament Sensor by wlbillmartin
...pyramid filament mount with filament sensor by wlbillmartin
thingiverse
pyramid filament mount with filament sensor
(9:30)