Thingiverse
SQ12 Lightweight Case by kamlooper
by Thingiverse
Last crawled date: 3 years ago
Lightweight case for the Quelima SQ12 camera. Stock case is around 9 grams, this one is printed from TPU and saves at least 5 grams. The infrared LEDs are eliminated on this design. Camera is friction fit into this case via dense foam lens surround. I used foam from a random rc product packing material and cut a 20x20x8mm cube, dremeled a 7mm center hole, sliced the foam in half to fit around the lens "shaft". Battery is inserted into the back of the case and then the camera board/foam is carefully worked into the case. With TPU you can flex it to get around the sightly protruding "usb" connector jack. Note that you will need to install the micro memory card after camera install. The friction fit of the foam holds the assembly snug, but may come out with a hard crash.
I put a hole at the back of the case to aid in removing the assembly, (pictures show a dremeled hole, stl file has the hole designed into it) note that you will be pushing on the battery so dont push too hard, I use a wood stir stick to help pry the camera board out while pushing from the back.. Again, be careful handing the camera guts, and pay extra attention to the ribbon, it is fragile.
The microphone is sitting on the side of the foam, but can be tuck in behind the assembly if not needed, or removed.
The mounting tab on the bottom is 17mm wide and 6mm tall. I mounted mine on a leader 120, you might need to edit this tab to suit your application. Since TPU can be hard to drill, I used a hot pin to poke a hole on the tab to accept a 2mm screw.
FYI I used a different lens on this camera as the stock one has a bit of a whitewash.
Have fun
I put a hole at the back of the case to aid in removing the assembly, (pictures show a dremeled hole, stl file has the hole designed into it) note that you will be pushing on the battery so dont push too hard, I use a wood stir stick to help pry the camera board out while pushing from the back.. Again, be careful handing the camera guts, and pay extra attention to the ribbon, it is fragile.
The microphone is sitting on the side of the foam, but can be tuck in behind the assembly if not needed, or removed.
The mounting tab on the bottom is 17mm wide and 6mm tall. I mounted mine on a leader 120, you might need to edit this tab to suit your application. Since TPU can be hard to drill, I used a hot pin to poke a hole on the tab to accept a 2mm screw.
FYI I used a different lens on this camera as the stock one has a bit of a whitewash.
Have fun
Similar models
thingiverse
free
DJ105 808 #16 camera mount by DirtyJ_Designs
...shed flight weight is around 12 grams.
this mount requires you print in a flexible material such as ninjaflex or some kinda tpu.
thingiverse
free
StereoPi Portable Enclosure
...able for mounting a simple push button.
the enclosure includes space for a battery pack but i was unable to acquire one that fit.
thingiverse
free
Lightweight Turnigy Action Camera Case by RotorGator
...mobius). the back panel has a cut-out allowing the led indicators to be seen. attach with a strap or velcro (i use 3m dual-lock).
thingiverse
free
20700 Battery Case by crazybob1215
...rse.com/thing:1415903). i did not include the retention tab and i added a ridge for better grip when pulling/pushing the lid off.
thingiverse
free
Xiaomi Yi Lens Protector and Mount by etracer
...e camera and is instead connected to the tabs, this style is potentially less robust. the failure point will likely be the tabs.
thingiverse
free
micro fpv camera case by MorganCoLLC
...er band to secure the back.
note: the lens hole may need a small amount of plastic shaved off depending on the printers accuracy.
thingiverse
free
DJI HD Camera lens cap with Pull Tab by Minute12
...he lens, is clean and smooth. tpu supports that are on the bottom of a surface are easy to remove on tpu, so it works out well.
thingiverse
free
Grommet Nest Security Camera by kmckernan
...rint 2x and sandwich the cable, there should be a friction fit into the hole.
can be painted later for a better low profile look.
thingiverse
free
Quanum V2 Lens Holder by GaryJohnson
...lens in quanum v2 at either extent depending how installed. friction fit around the lens arms, holds great without any adhesive.
thingiverse
free
C24 HARD TONEAU COVER by Jeremyslay1
...ll need to remove rear most tab of tool box pivot fingers.
fits under standard c24 bed topper for extra security and versatility.
Kamlooper
thingiverse
free
Ferrari Keychain by kamlooper
...int settings:
default settings, printer must be calibrated.
the one in the pictures was printed with pla
size:
18mm x 100mm x 4mm
thingiverse
free
Team C Gearcover Cap by kamlooper
...iverse
a cap for the team c gearcover, fits part to2005 found on the 2wd buggy, 2wd sc, 2wd stadium truck.
print with tpu or pla
thingiverse
free
Wizard x220 lightweight dual antenna mount by kamlooper
...
as title says, lightweight antenna mount, my own design.
inside diameter of tubes, 3.1mm, approx. 60º
printed in pla
%90 infill
thingiverse
free
Furibee Darkmax Antenna holder by kamlooper
...re to secure.
i can make another version with antennas pointing back upon request.
the darkmax is a great copter' by the way!
thingiverse
free
4 millimeter wrench for drones by kamlooper
...tom for a perfect fit.
it is 40mm long, 10mm wide at the wrench end, 6mm wide on the handle.
more tools to come as i invent them.
thingiverse
free
Leader 120 Offset Upper Brace by kamlooper
...reater range.
4mm forward offset
.5mm holes for micro tapping screws (i used tiny whoop screws)
.1 resolution
25% infill
tevo pla
thingiverse
free
Lizard 95 LED Holder by kamlooper
...p off and hold above the frame while installing this support, then reinstall strip, put screws in the side. done.
hope this helps
thingiverse
free
Atomstack Laser Power Switch Box by kamlooper
...ver build at your own risk!! my unit has a positive center on the plug/jack. be sure to triple check your polarity before using!!
thingiverse
free
215 Angel Wings Heart by fo0f5150ii
...gel wings heart by fo0f5150ii
thingiverse
a memorial heart for the 215 children found at the kamloops indian residential school.
Sq12
thingiverse
free
Libero SQ12 mount by Smtechmatane
...libero sq12 mount by smtechmatane
thingiverse
this a support for sq12 camera on top of libero 2.5
thingiverse
free
SQ12 Cam Mount by Tomakk
...sq12 cam mount by tomakk
thingiverse
here is an selfconstrusted quelima sq12 cam mount.
edit 07.07.2018:
v2 is now online.
thingiverse
free
SQ12 Cam Mount 40° by Tomakk
...sq12 cam mount 40° by tomakk
thingiverse
here is an sq12 cam mount with 40 degrees.
thingiverse
free
SQ12 camera mount by Habendanio
...
thingiverse
mount for sq12 camera to drone or rc vehicle.
1 set of files includes 30* tilt
files in openscad included to modify
thingiverse
free
SQ12 Casing by yoowicked
...fpv drone using a velcro strap or zip ties.
it has 30 degrees up tilt angle and it looks awesome with the led light it up.
enjoy!
thingiverse
free
SQ12 Bfight210 Mount 25° by Hackbert
...fight210 mount 25° by hackbert
thingiverse
sq12 mount for the bfight210
25° degrees
printed in tpu
two small zip ties to fix it.
thingiverse
free
Martian 2 sq12 mount by Kingc5464
...2 camera mount for a martain 2 drone.
i had to lay it flat on one side and add a lot of supports to get a decent print out of it.
thingiverse
free
SQ12 flat bottom mount by Mr_Teddy
...;s for the frame which has angled cam mount already.
just need some cable tie and 12mm velcro for the installation.
happy flight!
thingiverse
free
Kopis 1 ~ SQ12 Mount by robthomson
...:https://paypal.me/rtrctip
dont forget to drop past:https://www.rt-rc.comhttps://www.youtube.com/channel/ucput4zu-wag1nezn9ihbvug
thingiverse
free
SQ12 camera mount 30 degree by FreiGuy
...f you need to buy the camera, look on amazon for sq12 spy mini camera.
print with it laying on its side. have fun and fly fast.
Lightweight
design_connected
$11
Lightweight
...lightweight
designconnected
foscarini lightweight pendant lights computer generated 3d model. designed by tom dixon.
turbosquid
$15
Lightweight
...y free 3d model lightweight for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1361264)
turbosquid
$2
Lightweight Shield
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$29
Lightweight Pine Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Lightweight Task Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Chandelier Lightweight Foscarini
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
futuristic lightweight wheel
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
free
Lightweight structure system animated
...lightweight structure system animated
3dexport
https://www.dock4all.com/
turbosquid
$15
03 LIGHTWEIGHT PATTERN WALL
...ghtweight pattern wall for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1504846)
turbosquid
$15
02 LIGHTWEIGHT PATTERN WALL
...ghtweight pattern wall for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1504842)
Case
3d_export
$1
case
...case
3dexport
case
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case + cakes - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
showcase show-case glass case
glass-case for chips - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case shelving drawer
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case rack locker
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case drawer kitchen furniture
case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case cupboard shelving
glass case - 3d model for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case handbag suitcase
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
case suitcase
case 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Case
...case
archibase planet
locker case dresser
case - 3d model (*.gsm+*.3ds) for interior 3d visualization.