Thingiverse
Sovol SV01 SV02 SV03 Power Off Autoswitch by ThingsDesigner
by Thingiverse
Last crawled date: 3 years, 3 months ago
Für Deutsch bitte nach unten scrollen.
Automatic switch-off after printing, the simplest solution for the Sovol SV01/02/03.
This is the useful accessory that is missing from the SV01/02/03. A simple device to automatically turn off the printer after printing has finished.
If you don't trust yourself to solder this cable yourself, because you are working on a live cable, you can also buy a pre-assembled power cable in my shop, which is easy to attach without risk. Link is here:
http://www.keng.de/shop/product_info.php?cPath=1283_1284&products_id=18096
I do not assume any liability or guarantee for these self-assembly instructions. Everyone who works on live cables should be aware of the risk and what they are doing. Everything here is done at your own risk!
There are many expensive solutions out there involving relays, crafts, and accessories. This, on the other hand, is simple, inexpensive and quick to implement.
The idea behind it all was to put the on/off switch on the printer where it can turn itself off. The best place then turned out to be a point to the right of the X-axis that the printing carriage cannot normally reach due to the software end stops. This position is also more accessible for turning the printer on and off manually.
There are two possible solutions that I have already successfully implemented:
1) A modified power cable, which is connected instead of the supplied cable. This does not change anything on the printer itself and you can buy it in my shop, see above.
2) A short power cable, which is also connected to the on/off switch of the printer and can take over its task elsewhere. This solution is described below.
We need:
The housing from the STL here (please turn it in the slicer by 90 °, support is not necessary)
An approx. 75 cm long flat power cable (H03VV-F according to DIN VDE 0281)
An on/off switch (rocker switch) for 220V (e.g. from an old PC power supply, 21x15mm / 19x13mm)
Two matching cable lugs with lugs for connection to the existing switch
Soldering accessories and a steady hand
Method:
First the existing power cable is pulled out of the printer and the device is de-energized.
The two Allen screws that attach the housing with the on/off switch to the printer are loosened and the housing is carefully pulled forward. Now you can see two red wires going to the switch. Our additional cable is attached to this two wires. I decided on a solution with flat plugs with a branch, then I can still use the old switch. But you can also connect the new cable only with the two red cables and thus put the old switch out of operation, as you like.
On the other side, the cable is pulled through the new housing and soldered to the new switch (attach the switch with 0 down). The ventilation slot near by the power switch can be used as a cable passage.
Now the new switch only needs to be attached to the X-axis at the top right. To do this, loosen the screw, ideally put an Allen key through it from the other side so that the roll holder does not fall apart, attach the switch and screw everything tight again.
So that the printer now switches itself off after printing, the G-code in the slicer has to be adjusted a little:
Here is my attitude towards Cura:
In the device settings for Cura, insert the following in the section "End G code" above the last command "M84 X Y E":
; Auto-OFF
G4 S120; Pause 120 sec.
G28 X; Home X for safety
M211 S0; SW end stop off
G1 X302; goto power-off position
; If not powered off:
M211 S1; SW end stop on
The entire end of G-code then looks like this:
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-6 Z0.2 F2400 ;Retract and raise Z
G1 Z10 ;Raise Z more
G1 X0 Y240 F3000 ;Wipe out
G90 ;Absolute positionning
G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed
; Auto-OFF
G4 S60 ; Pause 120 sec.
G28 X ; Home X for safety
M211 S0 ; SW-Endstop off
G1 X302 ; goto Power-Off-Position
; If not powered off:
M211 S1
M84 X Y E ;Disable all steppers but Z
If necessary, the command G1 X302 must be adjusted somewhat if the printer does not hit the switch correctly (manufacturing tolerance) or if the whole thing is used with a different printer. Since the software end stops are deactivated, you should be particularly careful here, otherwise it will literally crash.
If everything has been done correctly, you can leave the old on/off switch in the 0 position and only switch the printer on and off with the new switch.
If you don't want the printer to switch itself off every time, e.g. because you sit next to it and want to start a new print immediately, then you can simply turn on the old switch and the printer will always stay on.
I hope you like this simple solution and that it finds many users.
DEUTSCH:
Automatisches Ausschalten nach dem Druckvorgang, die einfachste Lösung für den Sovol SV01/02/03.
Dies ist das nützliche Zubehör, was beim Sovol fehlt. Eine einfache Vorrichtung, um den Drucker nach Beenden des Druckvorgangs automatisch auszuschalten.
Wer sich nicht zutraut, dieses Kabel selbst anzulöten, da man ja an einem stromführenden Kabel arbeitet, der kann auch in meinem Shop ein fertig konfektioniertes Stromkabel kaufen, welches ohne Risiko und einfach anzubringen ist. Link ist hier:
http://www.keng.de/shop/product_info.php?cPath=1283_1284&products_id=18096
Für diese Selbstbauanleitung hier übernehme ich keinerlei Haftung oder Garantie. Jeder, der an stromführenden Kabeln arbeitet, sollte sich des Risikos bewusst sein und wissen, was er macht. Alles hier geschieht auf eigene Gefahr!
Es gibt viele teure Lösungen mit Relais, Bastelarbeit und Zubehör. Diese hier dagegen ist einfach und preiswert und auch schnell umzusetzen.
Die Idee hinter dem ganzen war, den Ein-/Ausschalter dort am Drucker anzubringen, wo er sich selbst ausschalten kann. Als bester Platz hat sich dann eine Stelle rechts an der X-Achse herausgestellt, die der Druckschlitten normalerweise durch die Software-Endstops nicht erreichen kann. Diese Position ist auch besser zum manuellen Ein- und Ausschalten des Druckers erreichbar.
Hiefür gibt es zwei Lösungswege, die ich schon erfolgreich umgesetzt habe:
1) Ein modifiziertes Stromkabel, welches anstelle des mitgelieferten Kabels angeschlossen wird. Dies verändert nichts am Drucker selbst und man kann es bei mir im Shop kaufen, s.o..
2) Ein kurzes Stromkabel, welches an den Ein-/Ausschalter des Druckers zusätzlich angeschlossen wird und dessen Aufgabe an anderer Stelle übernehmen kann. Dies Lösung wird im folgenden beschrieben.
Wir benötigen:
Das Gehäuse von der STL hier (bitte im Slicer um 90° drehen, Support ist nicht nötig)
Ein ca. 60 cm langes flaches Stromkabel (H03VV-F nach DIN VDE 0281)
Einen Ein-/Ausschalter (Wippschalter) für 220V (z.B. von einem alten PC-Netzteil, 21x15mm / 19x13mm)
Zwei passende Kabelschuhe mit Lasche zum Anschluss an den vorhandenen Schalter
Löt-Zubehör und eine ruhige Hand
Vorgehensweise:
Zuerst wird das vorhandene Stromkabel aus dem Drucker gezogen und das Gerät stromlos gemacht.
Die zwei Schrauben, die das Gehäuse mit dem Ein-/Ausschalter am Drucker befestigen werden gelöst und das Gehäuse vorsichtig nach vorne gezogen. Jetzt sieht man zwei rote Kabel, die zum Schalter gehen. An diese Kabel wird unser zusätzliches Kabel befestigt. Ich habe mich für eine Lösung mit Flachsteckern mit Abzweig entschieden, dann kann ich den alten Schalter noch zusätzlich benutzen. Man kann aber auch das neue Kabel nur mit den zwei roten Kabeln verbinden und den alten Schalter somit außer Betrieb setzen, wie es einem beliebt.
Auf der anderen Seite wird das Kabel durch das neue Gehäuse gezogen und an den neuen Schalter angelötet (den Schalter mit 0 nach unten anbringen). Als Kabeldurchgang bieten sich die Lüftungsschlitze rechts neben dem Stromschalter an.
Jetzt muss der neue Schalter nur noch oben rechts an der X-Achse befestigt werden. Hierzu die Schraube lösen, am besten von der anderen Seite einen Imbußschlüssel durchstecken, damit die Rollenhalterung nicht auseinanderfällt, den Schalter anbringen und alles wieder fest schrauben.
Damit der Drucker sich nach dem Druck jetzt selbst ausschaltet, muss noch der G-Code im Slicer etwas angepasst werden:
Hier meine Einstellung für Cura:
In den Geräteeinstellungen für Cura fügt man in der Sektion "Ende G-Code" über dem letzten Befehl "M84 X Y E" folgendes ein:
; Auto-OFF
G4 S120 ; Pause 120 sec.
G28 X ; Home X for safety
M211 S0 ; SW-Endstop off
G1 X302 ; goto Power-Off-Position
; If not powered off:
M211 S1; SW end stop on
Der gesamte Ende G-Code sieht dann folgendermaßen aus:
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-6 Z0.2 F2400 ;Retract and raise Z
G1 Z10 ;Raise Z more
G1 X0 Y240 F3000 ;Wipe out
G90 ;Absolute positionning
G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed
; Auto-OFF
G4 S60 ; Pause 120 sec.
G28 X ; Home X for safety
M211 S0 ; SW-Endstop off
G1 X302 ; goto Power-Off-Position
; If not powered off:
M211 S1
M84 X Y E ;Disable all steppers but Z
Der Befehl G1 X302 ist nötigenfalls etwas anzupassen, falls der Drucker den Ausschalter nicht richtig trifft (Fertigungstoleranz) oder das ganze bei einem anderen Drucker eingesetzt wird. Da die Software-Endstops deaktiviert sind, sollte man hier besonders aufpassen, sonst kracht es im wahrsten Sinne des Wortes.
Wenn alles richtig gemacht wurde kann man den alten Ein-/Ausschalter in der 0-Stellung belassen und schaltet den Drucker nur noch mit dem neuen Schalter Ein und Aus.
Wenn man nicht möchte, dass sich der Drucker jedes mal selbst ausschaltet, weil man z.B. daneben sitzt und sofort einen neuen Druck starten möchte, dann kann man den alten Schalter einfach ebenfalls einschalten und der Drucker bleibt immer an.
Ich hoffe, diese simple Lösung gefällt und findet viele Nutzer.
Automatic switch-off after printing, the simplest solution for the Sovol SV01/02/03.
This is the useful accessory that is missing from the SV01/02/03. A simple device to automatically turn off the printer after printing has finished.
If you don't trust yourself to solder this cable yourself, because you are working on a live cable, you can also buy a pre-assembled power cable in my shop, which is easy to attach without risk. Link is here:
http://www.keng.de/shop/product_info.php?cPath=1283_1284&products_id=18096
I do not assume any liability or guarantee for these self-assembly instructions. Everyone who works on live cables should be aware of the risk and what they are doing. Everything here is done at your own risk!
There are many expensive solutions out there involving relays, crafts, and accessories. This, on the other hand, is simple, inexpensive and quick to implement.
The idea behind it all was to put the on/off switch on the printer where it can turn itself off. The best place then turned out to be a point to the right of the X-axis that the printing carriage cannot normally reach due to the software end stops. This position is also more accessible for turning the printer on and off manually.
There are two possible solutions that I have already successfully implemented:
1) A modified power cable, which is connected instead of the supplied cable. This does not change anything on the printer itself and you can buy it in my shop, see above.
2) A short power cable, which is also connected to the on/off switch of the printer and can take over its task elsewhere. This solution is described below.
We need:
The housing from the STL here (please turn it in the slicer by 90 °, support is not necessary)
An approx. 75 cm long flat power cable (H03VV-F according to DIN VDE 0281)
An on/off switch (rocker switch) for 220V (e.g. from an old PC power supply, 21x15mm / 19x13mm)
Two matching cable lugs with lugs for connection to the existing switch
Soldering accessories and a steady hand
Method:
First the existing power cable is pulled out of the printer and the device is de-energized.
The two Allen screws that attach the housing with the on/off switch to the printer are loosened and the housing is carefully pulled forward. Now you can see two red wires going to the switch. Our additional cable is attached to this two wires. I decided on a solution with flat plugs with a branch, then I can still use the old switch. But you can also connect the new cable only with the two red cables and thus put the old switch out of operation, as you like.
On the other side, the cable is pulled through the new housing and soldered to the new switch (attach the switch with 0 down). The ventilation slot near by the power switch can be used as a cable passage.
Now the new switch only needs to be attached to the X-axis at the top right. To do this, loosen the screw, ideally put an Allen key through it from the other side so that the roll holder does not fall apart, attach the switch and screw everything tight again.
So that the printer now switches itself off after printing, the G-code in the slicer has to be adjusted a little:
Here is my attitude towards Cura:
In the device settings for Cura, insert the following in the section "End G code" above the last command "M84 X Y E":
; Auto-OFF
G4 S120; Pause 120 sec.
G28 X; Home X for safety
M211 S0; SW end stop off
G1 X302; goto power-off position
; If not powered off:
M211 S1; SW end stop on
The entire end of G-code then looks like this:
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-6 Z0.2 F2400 ;Retract and raise Z
G1 Z10 ;Raise Z more
G1 X0 Y240 F3000 ;Wipe out
G90 ;Absolute positionning
G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed
; Auto-OFF
G4 S60 ; Pause 120 sec.
G28 X ; Home X for safety
M211 S0 ; SW-Endstop off
G1 X302 ; goto Power-Off-Position
; If not powered off:
M211 S1
M84 X Y E ;Disable all steppers but Z
If necessary, the command G1 X302 must be adjusted somewhat if the printer does not hit the switch correctly (manufacturing tolerance) or if the whole thing is used with a different printer. Since the software end stops are deactivated, you should be particularly careful here, otherwise it will literally crash.
If everything has been done correctly, you can leave the old on/off switch in the 0 position and only switch the printer on and off with the new switch.
If you don't want the printer to switch itself off every time, e.g. because you sit next to it and want to start a new print immediately, then you can simply turn on the old switch and the printer will always stay on.
I hope you like this simple solution and that it finds many users.
DEUTSCH:
Automatisches Ausschalten nach dem Druckvorgang, die einfachste Lösung für den Sovol SV01/02/03.
Dies ist das nützliche Zubehör, was beim Sovol fehlt. Eine einfache Vorrichtung, um den Drucker nach Beenden des Druckvorgangs automatisch auszuschalten.
Wer sich nicht zutraut, dieses Kabel selbst anzulöten, da man ja an einem stromführenden Kabel arbeitet, der kann auch in meinem Shop ein fertig konfektioniertes Stromkabel kaufen, welches ohne Risiko und einfach anzubringen ist. Link ist hier:
http://www.keng.de/shop/product_info.php?cPath=1283_1284&products_id=18096
Für diese Selbstbauanleitung hier übernehme ich keinerlei Haftung oder Garantie. Jeder, der an stromführenden Kabeln arbeitet, sollte sich des Risikos bewusst sein und wissen, was er macht. Alles hier geschieht auf eigene Gefahr!
Es gibt viele teure Lösungen mit Relais, Bastelarbeit und Zubehör. Diese hier dagegen ist einfach und preiswert und auch schnell umzusetzen.
Die Idee hinter dem ganzen war, den Ein-/Ausschalter dort am Drucker anzubringen, wo er sich selbst ausschalten kann. Als bester Platz hat sich dann eine Stelle rechts an der X-Achse herausgestellt, die der Druckschlitten normalerweise durch die Software-Endstops nicht erreichen kann. Diese Position ist auch besser zum manuellen Ein- und Ausschalten des Druckers erreichbar.
Hiefür gibt es zwei Lösungswege, die ich schon erfolgreich umgesetzt habe:
1) Ein modifiziertes Stromkabel, welches anstelle des mitgelieferten Kabels angeschlossen wird. Dies verändert nichts am Drucker selbst und man kann es bei mir im Shop kaufen, s.o..
2) Ein kurzes Stromkabel, welches an den Ein-/Ausschalter des Druckers zusätzlich angeschlossen wird und dessen Aufgabe an anderer Stelle übernehmen kann. Dies Lösung wird im folgenden beschrieben.
Wir benötigen:
Das Gehäuse von der STL hier (bitte im Slicer um 90° drehen, Support ist nicht nötig)
Ein ca. 60 cm langes flaches Stromkabel (H03VV-F nach DIN VDE 0281)
Einen Ein-/Ausschalter (Wippschalter) für 220V (z.B. von einem alten PC-Netzteil, 21x15mm / 19x13mm)
Zwei passende Kabelschuhe mit Lasche zum Anschluss an den vorhandenen Schalter
Löt-Zubehör und eine ruhige Hand
Vorgehensweise:
Zuerst wird das vorhandene Stromkabel aus dem Drucker gezogen und das Gerät stromlos gemacht.
Die zwei Schrauben, die das Gehäuse mit dem Ein-/Ausschalter am Drucker befestigen werden gelöst und das Gehäuse vorsichtig nach vorne gezogen. Jetzt sieht man zwei rote Kabel, die zum Schalter gehen. An diese Kabel wird unser zusätzliches Kabel befestigt. Ich habe mich für eine Lösung mit Flachsteckern mit Abzweig entschieden, dann kann ich den alten Schalter noch zusätzlich benutzen. Man kann aber auch das neue Kabel nur mit den zwei roten Kabeln verbinden und den alten Schalter somit außer Betrieb setzen, wie es einem beliebt.
Auf der anderen Seite wird das Kabel durch das neue Gehäuse gezogen und an den neuen Schalter angelötet (den Schalter mit 0 nach unten anbringen). Als Kabeldurchgang bieten sich die Lüftungsschlitze rechts neben dem Stromschalter an.
Jetzt muss der neue Schalter nur noch oben rechts an der X-Achse befestigt werden. Hierzu die Schraube lösen, am besten von der anderen Seite einen Imbußschlüssel durchstecken, damit die Rollenhalterung nicht auseinanderfällt, den Schalter anbringen und alles wieder fest schrauben.
Damit der Drucker sich nach dem Druck jetzt selbst ausschaltet, muss noch der G-Code im Slicer etwas angepasst werden:
Hier meine Einstellung für Cura:
In den Geräteeinstellungen für Cura fügt man in der Sektion "Ende G-Code" über dem letzten Befehl "M84 X Y E" folgendes ein:
; Auto-OFF
G4 S120 ; Pause 120 sec.
G28 X ; Home X for safety
M211 S0 ; SW-Endstop off
G1 X302 ; goto Power-Off-Position
; If not powered off:
M211 S1; SW end stop on
Der gesamte Ende G-Code sieht dann folgendermaßen aus:
G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-6 Z0.2 F2400 ;Retract and raise Z
G1 Z10 ;Raise Z more
G1 X0 Y240 F3000 ;Wipe out
G90 ;Absolute positionning
G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed
; Auto-OFF
G4 S60 ; Pause 120 sec.
G28 X ; Home X for safety
M211 S0 ; SW-Endstop off
G1 X302 ; goto Power-Off-Position
; If not powered off:
M211 S1
M84 X Y E ;Disable all steppers but Z
Der Befehl G1 X302 ist nötigenfalls etwas anzupassen, falls der Drucker den Ausschalter nicht richtig trifft (Fertigungstoleranz) oder das ganze bei einem anderen Drucker eingesetzt wird. Da die Software-Endstops deaktiviert sind, sollte man hier besonders aufpassen, sonst kracht es im wahrsten Sinne des Wortes.
Wenn alles richtig gemacht wurde kann man den alten Ein-/Ausschalter in der 0-Stellung belassen und schaltet den Drucker nur noch mit dem neuen Schalter Ein und Aus.
Wenn man nicht möchte, dass sich der Drucker jedes mal selbst ausschaltet, weil man z.B. daneben sitzt und sofort einen neuen Druck starten möchte, dann kann man den alten Schalter einfach ebenfalls einschalten und der Drucker bleibt immer an.
Ich hoffe, diese simple Lösung gefällt und findet viele Nutzer.
Similar models
thingiverse
free
Creality Ender-3 Power Off Autoswitch by ThingsDesigner
...er einfach ebenfalls einschalten und der drucker bleibt immer an.
ich hoffe, diese simple lösung gefällt und findet viele nutzer.
thingiverse
free
BIQU BX Power Off Autoswitch by ThingsDesigner
...er.
deutsche user: bitte, wenn ihr mich unterstützen wollt, schaut doch auch einmal in meinen shophttps://www.3d-arbeitsplatz.de/
thingiverse
free
Creality CR-6 SE Power Off Autoswitch by ThingsDesigner
...er einfach ebenfalls einschalten und der drucker bleibt immer an.
ich hoffe, diese simple lösung gefällt und findet viele nutzer.
thingiverse
free
Oberwagenlaterne by stephanbrunker
... brücke über der öffnung halbwegs sauber gedruckt wird. die druckteile wurden danach abgeschliffen und mit acteon dampfbehandelt.
thingiverse
free
Kabeleinführung by da-Jimbo
...mkabel über einer laminatholzdecke zu haben.
das kabel wird inkl. stecker durch die klappe geführt und über der decke angesteckt.
thingiverse
free
Astra ashtray cover USB Panel / Opel Astra H USB Einsatz für Aschenbecher by DuWeisWer
...footwell.
!expertise and tools are required for the wireing!
!improper installation can lead to injury and damage to the vehicle!
thingiverse
free
Penhalter für Apple Pencil by SirThommes
...ehörkabels (4mm).
so kann man jetzt das kabel seitlich herausführen. ich hoffe, das ich den einen oder anderen damit helfen kann.
thingiverse
free
Sidewinder X1 Messuhrhalter by AFUDirk
...zu gefaehrlich war, wenn der extruder
nach links faehrt, habe ich eine version gemacht, die auf den bauteilluefter gesteckt wird.
thingiverse
free
Tronxy XY-2 Pro / XY2 Pro Wartungshalter Service Stellung by Flore84
...ht auf den druckerteilen liegt.
für den halterkopf ist eine unterstützung sinnvoll damit die aufnahme für den rahmen besser wird.
thingiverse
free
Sovol SV02 Power Off Autoswitch Rev. by Ilmdruck
... everyone who works on live cables should be aware of the risk and what they are doing. everything here is done at your own risk!
Autoswitch
thingiverse
free
iSocket Autoswitch Under Table Mount
...t for the cables. mirror it horizontally in your slicing program if you want it to point the other direction and show the labels.
thingiverse
free
Dual Block outlet cover with support for Tool/Vac Autoswitch by mikeyroth
...tool/vac autoswitch by mikeyroth
thingiverse
i wanted an outlet cover to support a tool/vac auto switch. here is my design .
thingiverse
free
Autoswitch OFF for Tevo's Black Widow by guss67
.... * message me here
designed in inventor
if you enjoy and want to support my work you can donate me on the link below,
thank you!
thingiverse
free
Sovol SV02 Power Off Autoswitch Rev. by Ilmdruck
... everyone who works on live cables should be aware of the risk and what they are doing. everything here is done at your own risk!
thingiverse
free
BIQU BX Power Off Autoswitch by ThingsDesigner
...er.
deutsche user: bitte, wenn ihr mich unterstützen wollt, schaut doch auch einmal in meinen shophttps://www.3d-arbeitsplatz.de/
thingiverse
free
Creality Ender-3 Power Off Autoswitch by ThingsDesigner
...er einfach ebenfalls einschalten und der drucker bleibt immer an.
ich hoffe, diese simple lösung gefällt und findet viele nutzer.
thingiverse
free
Creality CR-6 SE Power Off Autoswitch by ThingsDesigner
...er einfach ebenfalls einschalten und der drucker bleibt immer an.
ich hoffe, diese simple lösung gefällt und findet viele nutzer.
3dwarehouse
free
Kramer VP 211 Autoswitch
...kramer vp 211 autoswitch
3dwarehouse
kramer vp 211 autoswitch #211 #autoswitch #kramer #vp
Thingsdesigner
thingiverse
free
QR Code Cover for Sovol SV01 by ThingsDesigner
...l sv01 by thingsdesigner
thingiverse
i don´t want the qr code, so i replaced it with a cover like i do with my cr-6 and ender-3.
thingiverse
free
QR Code Cover for Creality Ender-3 by ThingsDesigner
...y ender-3 by thingsdesigner
thingiverse
i don´t like the qr code on my ender-3. so i designed a cover with the ender logo on it.
thingiverse
free
Satsana Remix for Ender 3V2 and Ender 3 with All Metal Hotend, BLTouch / 5015 Fan by ThingsDesigner
...an the normal one (see pictures). so i shortened the satsana as well.
this is a remix ofhttps://www.thingiverse.com/thing:4647053
thingiverse
free
Creality CR-6 SE Raspberry Pi 4 Case by ThingsDesigner
...flat on my bed and the back part with cura tree support.
for the camera mount you need two m3 screws and nuts from the grave box.
thingiverse
free
BIQU BX Power Off Autoswitch by ThingsDesigner
...er.
deutsche user: bitte, wenn ihr mich unterstützen wollt, schaut doch auch einmal in meinen shophttps://www.3d-arbeitsplatz.de/
thingiverse
free
Creality Ender-3 Power Off Autoswitch by ThingsDesigner
...er einfach ebenfalls einschalten und der drucker bleibt immer an.
ich hoffe, diese simple lösung gefällt und findet viele nutzer.
thingiverse
free
Sovol SV02 Power Off Autoswitch Rev. by Ilmdruck
...not be mounted on the rail as in the thingsdesigner solution, i changed the bracket. i just put the...
thingiverse
free
Creality CR-6 SE Power Off Autoswitch by ThingsDesigner
...er einfach ebenfalls einschalten und der drucker bleibt immer an.
ich hoffe, diese simple lösung gefällt und findet viele nutzer.
thingiverse
free
Ender 3 V2 Power Off Auto switch shutdown by omarhaasan
...3, ender 3 pro, cr6se and may others. ( thingsdesigner ) design very useful but required to un-screw bolt...
Sv02
thingiverse
free
Sovol SV02 Direct Drive Mod by dgarrett420
...sovol sv02 direct drive mod by dgarrett420
thingiverse
sv02 direct drive mod
thingiverse
free
BLT Bracket for Sovol SV02 with Mixing Hotend by Kotty
...2 with mixing hotend by kotty
thingiverse
this is a bl-touch bracket holder for using a mixing hotend at the sovol sv02 printer.
thingiverse
free
SV02 Fan Duct by RedSquirrelHobbies
...with the bed.
these will hit your bed clips if you're not careful!
print with petg and they will last longer!
happy printing!
thingiverse
free
Bracket for Laser Module SV02/Ender 3/pro / Ender 5/pro by Sovol
...v02: https://sovol3d.com/products/sovol-sv02-dual-extrusion-3d-printer
sovol laser module:https://sovol3d.com/products/laser-kits
thingiverse
free
Clip-On Purge Bucket / Wipe for Sovol SV02 by ThKu
...o multi-material use (imho):https://github.com/smartavionics/cura/releases
i have also attached my machine and extruder profiles.
thingiverse
free
Butterfly [sovol sv02] by Thundyt
...ering and spade. star may need minor sanding but should push fit into the space tightly and not need anything else to secure it.
thingiverse
free
Filament-Führungs-Rolle für SOVOL SV02 by MX-Trainer
...rwendung der rollen mit lager, werden 2 st. 608er kugellager benötigt.
ich habe die rolle aus tpu und den halter aus pla gedruckt
thingiverse
free
REMIX from Thundernut's ore Dual extrusion minecraft ore block by Ollie7802
...wanted to print the ore in one on my sv02 dual printer, so i...
thingiverse
free
Dual Color - Ghostship Benchy by FiveNights
...- ghostship benchy by fivenights thingiverse i recommend sovol sv02 3d printer (easy-to-use, dual-color 3d printer) remixed from jdmac174...
thingiverse
free
Sovol SV02 Power Off Autoswitch Rev. by Ilmdruck
... everyone who works on live cables should be aware of the risk and what they are doing. everything here is done at your own risk!
Sv03
thingiverse
free
SV03 Sovol LCD Cover by djcosmic2
...ol lcd cover by djcosmic2
thingiverse
modified by adding a cut on the left-hand side so it will fit over the sv03 lcd side mount
thingiverse
free
Sovol SV03 Ribbon Cable Holder by wliver
...or can use double sided tape. print long side down to use less support.
pla, 20-25% printed down on long side 0.2 with sovol sv03
thingiverse
free
Dial Indicator holder Sovol SV03 printer by BSA-LLC
...ter to better level the bed. its made in several pieces for ease of printing and variability of people's own dial indicators.
thingiverse
free
Sovol SV03 Tool Tray by Extech
...nsor bracket. i can post that as well if people are interested in it. i’m working on designing one for the sv01 and the sv03 now.
thingiverse
free
Sovol SV01 & SV03 Hemera Mounting plate by GreameGB
...otor current needs to be set to 940)
(filament sensor for some reason i had to set filament sensor inverting to "true")
thingiverse
free
Sovol SV01 & SV03 Hemera Mounting plate by GreameGB
...otor current needs to be set to 940)
(filament sensor for some reason i had to set filament sensor inverting to "true")
thingiverse
free
Sovol SV01 SV03 Titan Extruder E3D V6 by coffejunkie_de
...ust add hex nuts for bltouch mount and adjust bracket for pancake stepper.
v11 gives you 2mm extra space between tray and bracket
thingiverse
free
Sovol SV03 Diagonal Bracing Parts by BSA-LLC
...ur #6 machine screws to hold the eye bolts to the eye bolt plates. you can add super glue to the eye bolts to insure a tight fit.
thingiverse
free
Braket for Laser Module SV01 by Sovol
...sovol laser module: https://sovol3d.com/products/laser-kits sovol sv01: https://sovol3d.com/products/sv01-direct-drive-printer sovol sv03: https://sovol3d.com/products/sv03 ...
thingiverse
free
Sovol Dragonfly Part Cooling Fan Duct by bjaurelio
...not as long as the stock hotend on the sv01/sv03 ...
Sv01
design_connected
$16
Svarga SV01 Carpet
...svarga sv01 carpet
designconnected
mischioff svarga sv01 carpet computer generated 3d model.
thingiverse
free
Sovol SV01 Rail Cover
...sovol sv01 rail cover
thingiverse
this is a rail cover for the sovol sv01 printer
thingiverse
free
Sovol SV01 BLTouch Mount
...sovol sv01 bltouch mount
thingiverse
bltouch mount for sovol sv01, nozzle offset of -33, -11.
thingiverse
free
Sovol SV01 Logitech C270 Mount
...sovol sv01 logitech c270 mount
thingiverse
camera mount for sovol sv01
thingiverse
free
Sovol SV01 Rail Cover by Flamingbrad
...sovol sv01 rail cover by flamingbrad
thingiverse
added sovol logo for sv01 users
thingiverse
free
Zugentlastung Kabelführung Sovol SV01 by pcmaik
...zugentlastung kabelführung sovol sv01 by pcmaik
thingiverse
kabelführung für den sovol sv01
thingiverse
free
Sovol SV01 BLT base by Sir_Stig
...sovol sv01 blt base by sir_stig
thingiverse
just a remix for a sovol sv01 baseplate.
thingiverse
free
Braket for Laser Module SV01 by Sovol
...ducts/laser-kits
sovol sv01: https://sovol3d.com/products/sv01-direct-drive-printer
sovol sv03: https://sovol3d.com/products/sv03
thingiverse
free
SV01 Damper Foot (Fully Printable)
...sv01 damper foot (fully printable)
thingiverse
a nice and easy fully printable damper foot for the sv01
made with pla and tpu
thingiverse
free
X-Axis template for Sovol SV01 by piervania
...x-axis template for sovol sv01 by piervania
thingiverse
x-axis template for sovol sv01
Sovol
thingiverse
free
Sovol Knob
...sovol knob
thingiverse
replacement knob for sovol sv01
thingiverse
free
Template for Sovol FEP Film by Sovol
...e
on the sovol fep film, you need to drip holes, this template will help you and give you the correct position of all the holes.
thingiverse
free
Sovol 3d printed Comb by Sovol
... printed comb is comfortable and hair safe to use, it will give you tha same using experience as the comb you order in the store,
thingiverse
free
sovol cover
...sovol cover
thingiverse
this will make a cover for the circuit board on the back of the sovol screen. use supports.
thingiverse
free
SOVOL Bedhandle
...sovol bedhandle
thingiverse
a bed handle for the sovol printer
use support
for stock springs and the 10mm yellow springs
thingiverse
free
Sovol Lighting Logo Sign by Sovol
...r with auto leveling :https://sovol3d.com/products/sv03
buy sovol pla&tpu filament : https://sovol3d.com/collections/filament
thingiverse
free
Sovol SV01 Rail Cover
...sovol sv01 rail cover
thingiverse
this is a rail cover for the sovol sv01 printer
thingiverse
free
Sovol SV01 BLTouch Mount
...sovol sv01 bltouch mount
thingiverse
bltouch mount for sovol sv01, nozzle offset of -33, -11.
thingiverse
free
Sovol dial knob with finger
...sovol dial knob with finger
thingiverse
knob for sovol sv01 control panel. same as other, just added a finger.
thingiverse
free
Sovol SV01 Logitech C270 Mount
...sovol sv01 logitech c270 mount
thingiverse
camera mount for sovol sv01
Power
turbosquid
$100
power
...ower
turbosquid
royalty free 3d model power for download as on turbosquid: 3d models for games, architecture, videos. (1421990)
3d_export
$5
Power
...power
3dexport
3d_export
$5
power outlets
...power outlets
3dexport
power outlets
3ddd
$1
lion power
...lion power
3ddd
лев , статуя
lion power gold sculpture
3ddd
$1
Sea Power
...
компас , море , часы
часы с компасом sea power
3ddd
free
Meridiani / Power
...power
3ddd
meridiani , круглый
стол power производитель meridiani, диаметр 120,высота 67
3d_export
$5
Power Surge
...power surge
3dexport
the power surge is a all mesh carnival ride to lower in game part count and lag
turbosquid
$8
Airport Ground Power Unit (AXA Power )
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$50
Power Houser
...rbosquid
royalty free 3d model power houser for download as on turbosquid: 3d models for games, architecture, videos. (1333800)
3d_export
$5
power outlet
...power outlet
3dexport
power outlet<br>format file maya 2018, 3d max 2017, obj, fbx