Thingiverse
Snowgun / Air ejector / water spray by Zzat
by Thingiverse
Last crawled date: 3 years ago
Designed for snow making, only compressed air and a tank with (not pressured) water necessary. It can suck water from deep of more than 1 m. Water level must be below the snowgun position.
Assembly:
This thing contains of two 3D printable parts - ejector body and ejector nozzle (with variant B for basic usage and variant C for more power compressors). Then you need a compressor plug, 0,4 mm M6 nozzle for 3D printers and a hose with external diameter up to 9 mm.
Assembly the M6 nozzle for 3D printers. Power is depending on air pressure and a nozzle diameter. It is recommended to use 0,4 mm nozzle for hobby compressors and pressured air 0,6 to 0,8 MPa.
Also, it is necessary to screw-in a compressed air plug, see the picture. You can glue any pipe or hose with diameter up to 9 mm for water connection.
Use ejector nozzle B for first assembly with 0,4 mm 3D printer nozzle inside.
When it is fully assembled, connect the pressured air plug, place hose to the water and check functionality. Probably the hose will make bubbles instead of sucking the water. Then slowly screw-out the ejector nozzle until it will suck the water and start running. It makes too big water-drops if it is screwed-out too enough (low efficiency, high water consumption).
Notes:
For the best snow quality use pressured air with maximal possible pressure (max. 1,0 MPa). Then find the best nozzle diameter - your compressor probably is not designed for continuous working. Most of the hobby compressors are designed for cycles 2,5 min running with 7,5 min pause. Overloading can cause damage of your compressor!
When air is leaving the nozzle, it reduces pressure temperature and relative humidity also. It is the best possible enviroment for snow making.
Material: ABS, PETG
Resolution: 0,2 mm
Infill: 100%
Supports: No
Use at least 5 perimeters! There is pressured air inside.
Assembly:
This thing contains of two 3D printable parts - ejector body and ejector nozzle (with variant B for basic usage and variant C for more power compressors). Then you need a compressor plug, 0,4 mm M6 nozzle for 3D printers and a hose with external diameter up to 9 mm.
Assembly the M6 nozzle for 3D printers. Power is depending on air pressure and a nozzle diameter. It is recommended to use 0,4 mm nozzle for hobby compressors and pressured air 0,6 to 0,8 MPa.
Also, it is necessary to screw-in a compressed air plug, see the picture. You can glue any pipe or hose with diameter up to 9 mm for water connection.
Use ejector nozzle B for first assembly with 0,4 mm 3D printer nozzle inside.
When it is fully assembled, connect the pressured air plug, place hose to the water and check functionality. Probably the hose will make bubbles instead of sucking the water. Then slowly screw-out the ejector nozzle until it will suck the water and start running. It makes too big water-drops if it is screwed-out too enough (low efficiency, high water consumption).
Notes:
For the best snow quality use pressured air with maximal possible pressure (max. 1,0 MPa). Then find the best nozzle diameter - your compressor probably is not designed for continuous working. Most of the hobby compressors are designed for cycles 2,5 min running with 7,5 min pause. Overloading can cause damage of your compressor!
When air is leaving the nozzle, it reduces pressure temperature and relative humidity also. It is the best possible enviroment for snow making.
Material: ABS, PETG
Resolution: 0,2 mm
Infill: 100%
Supports: No
Use at least 5 perimeters! There is pressured air inside.
Similar models
thingiverse
free
Snowgun with external mixing by Zzat
...; water input (quick coupler for garden hose recommended), 3x m6 nozzle 0,4mm for 3d printers and a compressed air quick coupler.
thingiverse
free
Snowgun with external mixing by Zzat
... water input (quick coupler for garden hose recommended), 3x m6 nozzle 0,4 mm for 3d printers and a compressed air quick coupler.
grabcad
free
Piston air compressor
...piston air compressor
grabcad
piston stroke - 140 mm, piston diameter - 170 mm, outlet pressure - 0,6 mpa
grabcad
free
Rotary Screw Compressor (Industrial Compressed Air Treatment Plant)
..., the air gets pushed to the other end of the rotors (the ‘pressure side’) and new fresh air gets sucked in. (stp file is in rar)
grabcad
free
Rotary Screw Type Compressor
...advantage. the rotary screw compressors have additional advantages that make them perfect for mobile and stationary applications.
grabcad
free
Jet Engine
...led the turbine. the turbine is attached to the same shaft as the compressor. spinning the turbine causes the compressor to spin.
grabcad
free
COMPRESSOR ASSEMBLY
...compressor assembly
grabcad
compressor is used to as a source of compressed air.
grabcad
free
Viper 8 Jet Engine Compressor Assembly
...h turns to run the compressor and other accessories. finally the high temperature, high velocity air exits the exhaust as thrust.
thingiverse
free
Aquarium air hose holder by MCP1981
...contact with water has a recess to break the water surface tension and prevent water be sucked on the outer side of the aquarium.
grabcad
free
Jet engine with propeller shaft
...compressed air, burning the mixture in the combustor, and then passing the hot, high pressure air through a turbine and a nozzle.
Snowgun
thingiverse
free
Snowgun with external mixing by Zzat
...; water input (quick coupler for garden hose recommended), 3x m6 nozzle 0,4mm for 3d printers and a compressed air quick coupler.
thingiverse
free
Snowgun with external mixing by Zzat
... water input (quick coupler for garden hose recommended), 3x m6 nozzle 0,4 mm for 3d printers and a compressed air quick coupler.
cg_trader
$120
T60 snow gun
...t60 snow gun cg trader t60 snowgun ...
3dwarehouse
free
Snowgun
...snowgun
3dwarehouse
snowgun #snowgun
3dwarehouse
free
lenko snow gun
...my first lenko snow gun #fa540 #lenko #snow #snow_gun #snowgun ...
3dwarehouse
free
canon haute pression
...#cañon #chairlift #gondola #neige #nieve #ski #skilift #snow #snowboard #snowgun ...
3dwarehouse
free
canon a neige basse pression
...#canon #cañon #chairlift #neige #nieve #ski #skilift #snow #snowboard #snowgun ...
Zzat
thingiverse
free
Baby gingerbread cutter by Zzat
...baby gingerbread cutter by zzat
thingiverse
baby gingerbread cutter
thingiverse
free
Razor blade by Zzat
...razor blade by zzat
thingiverse
designed for commercial blades.
material: abs, petg
resolution: 0,2 mm
infill: 20%
supports: no
thingiverse
free
Don Bosco Salesians logo by Zzat
...don bosco salesians logo by zzat
thingiverse
don bosco salesians logo with possibility to wearing on clothes.
thingiverse
free
Filter box for resuscitation mask by Zzat
...e
designed for adding a filter inside and connecting to the resuscitation mask.
the mask is necessary to seals well on the face.
thingiverse
free
.22LR training cartridge for firearm by Zzat
... wrong dimensions, it could get stuck inside your firearm.
recommended material: abs, petg
resolution: 0,1mm or less
infill: 100%
thingiverse
free
2x screw nut M8, 45° rotated by Zzat
...ul for your own mechanical constructions based on m8 screw rods.
material: abs, petg
resolution: 0,2 mm
infill: 100%
supports: no
thingiverse
free
Cable holder for 3 phase circuit breaker by Zzat
...der for 3 phase circuit breaker mounted on a din rail
screws necessary
material: petg
resolution: 0,3 mm
infill: 20%
supports: no
thingiverse
free
Malagutti F12 Phantom scooter front light frame by Zzat
...hingiverse
front light frame for malagutti f12 phantom scooter
recommended material: petg
resolution: 0,2mm or less
infill: 100%
thingiverse
free
6.35mm Browning training cartridge for firearm by Zzat
... wrong dimensions, it could get stuck inside your firearm.
recommended material: abs, petg
resolution: 0,1mm or less
infill: 100%
thingiverse
free
9mm Luger training cartridge for firearm by Zzat
... wrong dimensions, it could get stuck inside your firearm.
recommended material: abs, petg
resolution: 0,1mm or less
infill: 100%
Ejector
3d_export
$6
dental ejector
...s to your saliva ejectors and parts must be sterilized or discarded with respect to the safety of your patients and your doctors.
3d_export
$12
dental ejector
...ctors and parts must be sterilized or discarded with respect to the safety of your patients and your doctors.<br>formato de
3d_export
$12
dental ejector and retractor kit
...s to your saliva ejectors and parts must be sterilized or discarded with respect to the safety of your patients and your doctors.
3d_export
$15
ejector with arc aspirator
...they are suitable for autoclaving. any questions or if you need a new model with different dimensions do not hesitate to write me
turbosquid
$65
Smith & Wesson Revolver
...royalty free 3d model smith & wesson .455 hand ejector for download as 3ds, obj, and fbx on turbosquid:...
3d_export
$10
2-Plate Plastic Injection Molding Equipment
...the essential parts such as: core & cavity, plates, ejector pins, cooling channel, gate & runner system, sprue bush,...
3d_export
$600
us air force f-35 bf-4 lightning ii with pilot
...realistic etos system, detailed animated internal bay, detailed external ejector rack, animated landing gears, over 22 articulated...
3d_export
$600
us air force f-35 af-10 lightning ii with pilot
...realistic etos system, detailed animated internal bay, detailed external ejector rack, animated landing gears, over 22 articulated elements.<br>-------------------------------------------------------------<br>camelot inc....
3dfindit
free
Ejectors
...ejectors
3dfind.it
catalog: arag
sketchfab
$8
Medical Ejector
...s another way for your character to administrate a health dose. - medical ejector - buy royalty free 3d model by shockwavegamez01
Spray
3d_export
$5
spray
...spray
3dexport
spray paint can
archibase_planet
free
Spray
...spray
archibase planet
spray bathroom ware
spray - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
sanitary ware spray
spray - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
spray sanitary ware
spray - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
spray sanitary ware
spray n260911 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
spray bottle
spray n050313 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
hair spray makeup preparation
spray 1- 3d model for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
hair spray makeup preparation
spray 2 - 3d model for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
hair spray makeup preparation
spray 3 - 3d model for interior 3d visualization.
archibase_planet
free
Spray
...spray
archibase planet
spray sanitary ware aerosol
spray - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Water
turbosquid
$2
water bin water tank
...e 3d model water bin water tank for download as blend and obj on turbosquid: 3d models for games, architecture, videos. (1594026)
archibase_planet
free
Water purifier
... purifier water purification water treatment
water purifier n050914 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
3d_ocean
$6
glass water
...glass water
3docean
clear glass glass water
glass filled with water
3ddd
$1
Watering pot
...watering pot
3ddd
watering pot лейка поливалка , лейка
watering pot
3d_ocean
$12
Water Dispenser
...dispenser furnishings lowpoly water
this is a water dispenser hot water for tea is winter and summer is cold for souls. have fun!
3d_ocean
$2
Water
...water
3docean
this is a tile able, hand painted water texture tile. included is one versions at 512×512 pixels in .tga format.
3d_export
$6
water tanker
...water tanker
3dexport
water tanker
3d_export
$6
water bottle
...water bottle
3dexport
water bottle
3d_export
$5
water bottle
...water bottle
3dexport
water bottle
3d_export
$5
water thermos
...water thermos
3dexport
water thermos
Air
3ddd
$1
Calligaris air
...calligaris air
3ddd
air , calligaris
cтул calligaris air
3ddd
$1
Air freshener
...air freshener
3ddd
air freshener , освежитель
air freshener
design_connected
$16
Air
...air
designconnected
flexform air lounge chairs computer generated 3d model. designed by antonio citterio.
turbosquid
$250
Heat pump air air
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
air
...air
3dexport
3ddd
$1
Кухня AIR
...кухня air
3ddd
air , мария
кухня air фабрики "мария"
3ddd
$1
Лампа AIR
...лампа air
3ddd
boconcept , air
настольная лампа air, boconcept. в50½xø32см
3d_export
$40
air deflector
...air deflector
3dexport
air deflector
3d_export
$15
air purifier
...air purifier
3dexport
air purifier
3d_export
$5
macbook air
...macbook air
3dexport
macbook air