Similar models
thingiverse
free
Balz Fidget by Nicolas_T
...aring and 6x 10mm ballbearing.
the bearings snaps into the holes when printed in abs. pla will leave some play on the 10mm balls.
thingiverse
free
Snap-On Y-Flag by Herbsti
...snap-on y-flag by herbsti
thingiverse
easy to install flag for 10mm rods
thingiverse
free
Linear carriage 10mm in 2 versions by Minic24
... without bearing but with groove for snap ring. 35x40x25mm
for bearing: 19x29x10mm
no with bearing dummy and snap ring (20x1mm)
thingiverse
free
Ender 3 Snap On 10mm LED Light Bar
... 10mm wide and 15cm length led strips
fixation replaced by a snap-on system inspired by https://www.thingiverse.com/thing:3015832
thingiverse
free
Mini vibrating motor snap-fit holster by AKAMEDIASYSTEM
...d 10mm long, with a little collar at the top to grip a 2.5mm diameter bearing housing (which is built into the motor in question)
thingiverse
free
Snap Stick, Bar, Interlocking, Math by lgbu
...arious lengths and see how children can make with them. as alwasys, remember to observe safety rules when working with children.
thingiverse
free
Snap cable organizer with screw mount by Achuyman
... to print, it takes me 6 minutes to print one, and helps me to stay somewhat organised.
it holds 20mm x 10mm, scale up if needed.
thingiverse
free
Magnetic Snapping Toothbrush Holder by jhwblender
...magnetic snapping toothbrush holder by jhwblender
thingiverse
magnetic tooth brush holder.
requires 1 magnet of size 10mm by 2mm
thingiverse
free
snap buckle by alexandrestcyr
...snap buckle by alexandrestcyr
thingiverse
2 pieces printed snap buckle , snap well!!!
thingiverse
free
RCX 1804 2400kv Motor Mount (10mm Carbon Box Tubing) by wilsonp195
...ng problematic, snap onto box tubing and secure with 3mm nylon nut and bolt.
medium quality slic3r print settings recommended.
Filler
thingiverse
free
Fillerment end holder by nattyward789987
...fillerment end holder by nattyward789987
thingiverse
neat fillerment
thingiverse
free
Outlet filler plate by Coder96
...outlet filler plate by coder96
thingiverse
outlet filler plate
thingiverse
free
Dual Filler bracket by Sindrg
...dual filler bracket by sindrg
thingiverse
a remix that holds two fillers.
thingiverse
free
Filler (hex themed) by seb_g
...iverse
a hexagon themed filler remix of filler (https://www.thingiverse.com/thing:3020026).
main goals
minimal support
no fillet
thingiverse
free
water balloon filler by WhiteTrashFPV
...water balloon filler by whitetrashfpv
thingiverse
water balloons filler made for a household sink.
thingiverse
free
Filler cap for camper by Spectrumteacher
...filler cap for camper by spectrumteacher
thingiverse
filler cap for watertank of a roller team camper
thingiverse
free
Angle Grinder Filler
...ngiverse
dewalt dw400 angle grinder filler. allows use of flat thin blades without the exctended hub in the middle of the disk.
thingiverse
free
Airsoft Buttstock filler. by below_cho
...airsoft buttstock filler. by below_cho
thingiverse
this buttstock filler is to fill in the space when the buttstock was removed.
thingiverse
free
Joint Filler by SebaLopez
...assembled in the shape of a cone.
a good recommendation is to sand it the narrowest part so that the weed passes without problems
thingiverse
free
Joint Filler by SebaLopez
...iller made especially for pre-rolled cone-shaped joints.
advice for weed to pass without problems is to sand the surface a little
10Mm
thingiverse
free
Wrench 10mm
...wrench 10mm
thingiverse
wrench 10mm. function not verified.
thingiverse
free
Cube 10mm by Gavin_V
...cube 10mm by gavin_v
thingiverse
10mm cube
thingiverse
free
10mm spacer by groyer60
...10mm spacer by groyer60
thingiverse
10mm spacer
thingiverse
free
10MM Wrench by 14DDUNK
...10mm wrench by 14ddunk
thingiverse
10mm wrench
thingiverse
free
10mm cap by matt8588
...10mm cap by matt8588
thingiverse
this is a 10mm cap, print in flexible plastic
thingiverse
free
10mm shaft center mount - Wellenaufnahme 10mm by Krusven
...ahme 10mm by krusven
thingiverse
this is a 10mm shaft mount to attach everything centered to a 30mm nut profil with 3 m5 screws.
thingiverse
free
10mm DreamCatcher by MicroMotorWarehouse
...mm dreamcatcher frame
more details about required components here:https://micro-motor-warehouse.com/collections/10mm-dreamcatcher
thingiverse
free
clamp 10mm by aviator645
...clamp 10mm by aviator645
thingiverse
clamp for prusa i3 axis 10mm
h=25mm
thingiverse
free
Calibration Cube 10mm x 10mm x 10mm by Fr8Dog
...olerance using this cube. the arrow points in the y-axis direction and is how i keep track of xyz orientation following printing.
thingiverse
free
10mm Cannon by Nicolas-F
...10mm cannon by nicolas-f
thingiverse
10mm cannon with a 10mm munition and a blackpowder charger.
Snap
thingiverse
free
BUTTON-SNAP
... shorts, etc.
best made of strong material, petg, abs, etc.
mine was made from petg to replace a snap broken on a pair of shorts.
thingiverse
free
snap buckle by alexandrestcyr
...snap buckle by alexandrestcyr
thingiverse
2 pieces printed snap buckle , snap well!!!
thingiverse
free
Snap On logo by Cheeky81
...your toolbox.
disclaimer:
snap-on is a trademark, registered in the united states and other countries, of snap-on incorporated.
thingiverse
free
snap cubes by andrew647
...snap cubes by andrew647
thingiverse
snap cubes
thingiverse
free
Snapping Turtle by xinghcy0311
...snapping turtle by xinghcy0311
thingiverse
snapping turtle
thingiverse
free
Snap Box
...snap box
thingiverse
this is a box convenient for storing small items, e.g. board game pawns etc... lid snaps in very nicely.
thingiverse
free
snap buckle by OleEichhorn
...snap buckle by oleeichhorn
thingiverse
simple snap buckle
thingiverse
free
Snap on logo by Plastic_Innovations
...snap on logo by plastic_innovations
thingiverse
just a simple snap-on logo.
thingiverse
free
Snap bracelet/necklace
...snap bracelet/necklace
thingiverse
cool snap bracelet/necklace