Thingiverse
Skyzone Sky02 - better Faceplate / Fan Mod by NatroNx
by Thingiverse
Last crawled date: 3 years ago
After a lot of hours of trying I've finally created this thing.
The goal was to have a Fan and a on/off Switch on my Skyzone without modifing my goggles itself and without loosing warranty.
Every button is still usable (even better then before, bacause the "cap" gives some guidance where the buttons are.
How to assemble it:
Print the 3 Parts as shown above. - everything can be printed without supports
1) Cap: Screw a 5.5/2.1 jack in the left side. Wire and solder it through the mounting hole on the back of the cap.
I used this jack:https://www.conrad.at/de/niedervolt-steckverbinder-buchse-einbau-vertikal-55-mm-21-mm-1-st-738190.html
Get the wire through the tunnel and solder it to the switches (one switch for the Fan, the other one for the goggles itself.
I used these switches:https://www.conrad.at/de/kippschalter-250-vac-3-a-1-x-einein-goobay-knx-1-rastend-1-st-701343.html
and this fan:https://www.conrad.at/de/axialluefter-12-vdc-594-mh-l-x-b-x-h-30-x-30-x-10-mm-sunon-ha30101v3-0000-a99-184263.html
The switch for the goggles itself has to be cabled to 5.5/2.1 plug that will plug into the goggles later.https://www.conrad.at/de/niedervolt-anschlusskabel-niedervolt-stecker-kabel-offenes-ende-55-mm-21-mm-voltcraft-2-m-1-st-749163.html
Once everything cabled and the Fan is mouted you can screw on the RotorRiot Fanguard and fill the mounting hole with hot glue (not mandatory)
2) The faceplate it thin enough to bend (you can apply some heat if needed in your oven -
All the faceplates I've printed (in PETG) was easy enough to bend, even without applying heat. And I've printed a lot until it was perfect.
Then put it on your goggles. The small clamps on the faceplate will hold it in place.
Push it to the top and screw it together with the "cap" - 4 Small M3 screws are needed. Countersunk flat heads will suit best. Now everything is secured.
3) Final steps: Get the foam that came with your Skyzones and stick it onto the new faceplate. Get out and fly your quad.
The goal was to have a Fan and a on/off Switch on my Skyzone without modifing my goggles itself and without loosing warranty.
Every button is still usable (even better then before, bacause the "cap" gives some guidance where the buttons are.
How to assemble it:
Print the 3 Parts as shown above. - everything can be printed without supports
1) Cap: Screw a 5.5/2.1 jack in the left side. Wire and solder it through the mounting hole on the back of the cap.
I used this jack:https://www.conrad.at/de/niedervolt-steckverbinder-buchse-einbau-vertikal-55-mm-21-mm-1-st-738190.html
Get the wire through the tunnel and solder it to the switches (one switch for the Fan, the other one for the goggles itself.
I used these switches:https://www.conrad.at/de/kippschalter-250-vac-3-a-1-x-einein-goobay-knx-1-rastend-1-st-701343.html
and this fan:https://www.conrad.at/de/axialluefter-12-vdc-594-mh-l-x-b-x-h-30-x-30-x-10-mm-sunon-ha30101v3-0000-a99-184263.html
The switch for the goggles itself has to be cabled to 5.5/2.1 plug that will plug into the goggles later.https://www.conrad.at/de/niedervolt-anschlusskabel-niedervolt-stecker-kabel-offenes-ende-55-mm-21-mm-voltcraft-2-m-1-st-749163.html
Once everything cabled and the Fan is mouted you can screw on the RotorRiot Fanguard and fill the mounting hole with hot glue (not mandatory)
2) The faceplate it thin enough to bend (you can apply some heat if needed in your oven -
All the faceplates I've printed (in PETG) was easy enough to bend, even without applying heat. And I've printed a lot until it was perfect.
Then put it on your goggles. The small clamps on the faceplate will hold it in place.
Push it to the top and screw it together with the "cap" - 4 Small M3 screws are needed. Countersunk flat heads will suit best. Now everything is secured.
3) Final steps: Get the foam that came with your Skyzones and stick it onto the new faceplate. Get out and fly your quad.
Similar models
thingiverse
free
SkyZone V2 goggles faceplate with fan by Motorpixiegimbals
...gles faceplate with fan by motorpixiegimbals
thingiverse
faceplate for skyzone v2 (3d) goggles with optional fan (25mm or 30mm).
thingiverse
free
Skyzone SKY01 Goggle / FatShark Dominator Headset Faceplate Mod Fan Spacer by teckn0
...t the faceplate isn't butted against it.
example build can be found at:https://johnbrisbois.com/content/skyzone_sky01_refresh
thingiverse
free
Skyzone V3 (SKY02S V+) faceplate with fan by supiiik
...v-goggles-p-1062372.html?p=kr21057480416201611g
fits better on my nose, block more sun (it's 2mm thickness, instead of 1,2mm)
thingiverse
free
Latte Panda Case with Fan and Heatsink by seipekm
...:https://www.conrad.at/de/waermeleitfaehiges-klebeband-03-mm-14-wmk-l-x-b-40-mm-x-40-mm-kerafol-keratherm-kl-90-40x40-181133.html
thingiverse
free
Skyzone V2 faceplate - NO FAN by NachosFPV
...te with no fan needed.
do not print as .stl file shows, print as second photos shows!
i found it better to fit with 98% resize :)
thingiverse
free
SkyZone V2 goggles faceplate less "Magic Way" by Lovincup
...iece from freakyattic's thing below.
this is for the non-3d version of the skyzones.
http://www.thingiverse.com/thing:1109091
thingiverse
free
Skyzone Goggles top Toggle adapter with Fatshark Faceplate by Enders13
...se
the fatshark faceplate fan covers the top adjuster for contrast and brightness so i made a simple slider to allow adjustment.
grabcad
free
12V DC Connector
....conrad.de/de/niedervolt-anschlusskabel-niedervolt-stecker-offenes-ende-55-mm-21-mm-bkl-electronic-2-m-1-st-1082733.html?altof=an
thingiverse
free
Fatshark & Skyzone Faceplate by soselamet
...require some cuts on the faceplate.
you can buy it from ebay : https://www.ebay.com/itm/fatshark-skyzone-faceplate/263644890686
thingiverse
free
no-hell fan cover only - remix of Skyzone V3 (SKY02S V+) faceplate with fan by faboaic
...s but some users from a quadcopter forum ( http://www.kopterforum.at ) wanted me to print this great upgrade for them.
thanks :-)
Natronx
thingiverse
free
Wedding Cake Topper by NatroNx
...nx
thingiverse
a wedding cake topper - looks best when printed in 2 colors
edit: added custom date by request
edit: another date
thingiverse
free
Print Bed Scraper (fixed) by NatroNx
...by natronx
thingiverse
a fixed version of the print bed scraper i found here on thingiverse.
the original had a gap in the model
thingiverse
free
TS100 Solder Box by NatroNx
...ut a 19v notebook cahrger and a makita 19v battery mount in the box to use the solder iron either on battery or with the charger.
thingiverse
free
Tablet Dock for Odys Wintab Ares9 by NatroNx
...
thingiverse
a dock for my tablet. its fits on a 200x200 bed when you turn the dock 45°
on the buttom are holes for rubber feet
thingiverse
free
Robomow Knob MS1800 by NatroNx
...er material will work. tpu will just feel "softer" - as the original one.
no support neeed. no overhangs. easy printing
thingiverse
free
Star Wars - 2 color Logo by NatroNx
...m zero to five millimeters and the second one from five to ten millimeters. changed the color between the processes.
worked great
Sky02
thingiverse
free
Skyzone sky02 v+ fan mod by littlbox
...skyzone sky02 v+ fan mod by littlbox
thingiverse
skyzone sky02 v+ fan mod for 20x20 mm fan. print in tpu.
thingiverse
free
Masque pour lunettes Skyzone SKY02 V3 by Arnaud29
... arnaud29
thingiverse
masque pour lunettes skyzone sky02 en adaptant le ventilateur 25mm + le bouton + la mousse du kit fatshark
thingiverse
free
Skyzone SKY02 Skin (TPE) by Vincentpartman
...cuting of supports, you can smooth the tpe with some hot tool, like soldering iron (clean soldering iron).
good luck printing it.
thingiverse
free
Skyzone V3 (SKY02S V+) faceplate with fan by supiiik
...v-goggles-p-1062372.html?p=kr21057480416201611g
fits better on my nose, block more sun (it's 2mm thickness, instead of 1,2mm)
thingiverse
free
SKYZONE (SKY02) Faceplate Fan-Mod by doomkill
... fancap!
the fancap is a remix version from: https://www.thingiverse.com/thing:1572123
you do not need the spacer plate.
have fun
thingiverse
free
Skyzone Sky02 External Receiver Module Bay
... why i don't have any final photo.
i'll put some updates when it's complete, even with the cables connection diagram.
thingiverse
free
no-hell fan cover only - remix of Skyzone V3 (SKY02S V+) faceplate with fan by faboaic
...s but some users from a quadcopter forum ( http://www.kopterforum.at ) wanted me to print this great upgrade for them.
thanks :-)
thingiverse
free
Skyzone V2 Faceplate for Fatshark foam by FENIX_
...fatshark foam by fenix_ thingiverse made for the skyzone sky02 to fit the fatshark foam linked below. the original...
thingiverse
free
Skyzone goggles fan mod by oldhui
...skyzone goggles fan mod by oldhui thingiverse the skyzone sky02 v+ 3d is a nice pair of goggles but...
Skyzone
thingiverse
free
Batteriehalterung (Skyzone) by Fliega
...batteriehalterung (skyzone) by fliega
thingiverse
batteriehalterung (skyzone)
thingiverse
free
skyzone fan holder by geralddejager
...skyzone fan holder by geralddejager
thingiverse
this fits onto the skyzone v2 goggles.
thingiverse
free
Skyzone VTX202 Mount by citybirdFPV
...skyzone vtx202 mount by citybirdfpv
thingiverse
30.5mm mount for skyzone 3d vtx
thingiverse
free
Fatshark & Skyzone Faceplate by soselamet
...require some cuts on the faceplate.
you can buy it from ebay : https://www.ebay.com/itm/fatshark-skyzone-faceplate/263644890686
thingiverse
free
Support for corrective lenses (Skyzone - Fatshark)
...giverse
supports for corrective lenses, works for my skyzone sky03o (and probably for the other skyzone as well as the fatshark)
thingiverse
free
Skyzone stx202 + 3D camera by Bugay
...skyzone stx202 + 3d camera by bugay
thingiverse
skyzone stx202
camera 3d
thingiverse
free
skyzone hb5808 diversity by karnaugh
... hb5808 diversity by karnaugh
thingiverse
skyzone hb5808 diversity external installation
filament: abs
infill: 100%
support: yes
thingiverse
free
Case for battery SkyZone 03O
...case for battery skyzone 03o
thingiverse
case for battery skyzone 03o. size battery 722035 mm 3s 1000 mah turnigy
thingiverse
free
Skyzone theer flying wing by macabox
...skyzone theer flying wing by macabox
thingiverse
skyzone theer flying wing... it´s to cool the esc
thingiverse
free
skyzone lens adapter
...skyzone lens adapter
thingiverse
dioptrical lens frame for fpv glasses
Faceplate
turbosquid
$4
Oil fitting faceplate
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
thingiverse
free
faceplate by lwoowllwoowl
...faceplate by lwoowllwoowl
thingiverse
faceplate
thingiverse
free
faceplate remix by lwoowllwoowl
...faceplate remix by lwoowllwoowl
thingiverse
faceplate remix
thingiverse
free
faceplate by mbot3d
...plate by mbot3d
thingiverse
this is a faceplate designed with proe.
the part photo showed is printed using our 3d printer, mbot.
thingiverse
free
Gingery Faceplate by NothingComplicated
...gingery faceplate by nothingcomplicated
thingiverse
the gingery faceplate pattern with draft where needed for sandcasting.
thingiverse
free
Wordclock faceplate by danowall
...eways.com/product/lm5ke6je3/wristwatch-faceplate-helveticahttps://www.shapeways.com/product/6lgvb53sy/wordclock-faceplate-stencil
thingiverse
free
XBox SD616T Faceplate Adapter
... modified to work in an original xbox. this faceplate adapter will allow the drive to carry the standard original xbox faceplate.
thingiverse
free
Anycubic faceplate by MY3MAGS
...anycubic faceplate by my3mags
thingiverse
go to allnthefam.com for a chance to win a $50 amazon gift card.
delta faceplate
thingiverse
free
GamePi20 Faceplate by ShoesForClues
...faceplate by shoesforclues
thingiverse
a faceplate for the waveshare gamepi20 which has a proper d-pad and non spinning buttons.
thingiverse
free
Huntron 1000 Faceplate by 360alaska
...huntron 1000 faceplate by 360alaska
thingiverse
replacement faceplate for huntron 1000
Mod
design_connected
$13
MOD. 4233 - MOD. 4234 Table Lamp
...mod. 4233 - mod. 4234 table lamp
designconnected
arcahorn mod. 4233 - mod. 4234 table lamp computer generated 3d model.
design_connected
$11
MOD.1095
...mod.1095
designconnected
mod.1095 computer generated 3d model. designed by sarfatti, gino.
3ddd
$1
fireplaces mod Spec
...fireplaces mod spec
3ddd
камин
fireplaces mod spec 180x90x125h
3ddd
free
Flos Mod. 2129
... mod
фабрика: flos
модель: mod. 2129
описание: подвесной светильник, металл, белый, черный.
сайт: www.flos.com
turbosquid
$34
Mod Lamp.c4d
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$32
MOD A 001
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$29
Maars Mod
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Mod 70..
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
MOD Sofa
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Mod-Lite
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Fan
3d_export
$5
fan
...fan
3dexport
fan 3d model, table fan, fan, electric fan, ventilator
archibase_planet
free
Fan
...fan
archibase planet
fan large fan
fan out n260707 - 3d model for interior 3d visualization.
archibase_planet
free
Fan
...fan
archibase planet
fan ceiling fan ventilator
fan stealth n300615 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$15
fan
...fan
3dexport
is an ancient fan
3ddd
$1
Fan-C-Fan by marco gallegos
...n-c-fan by marco gallegos
3ddd
вентилятор , marco gallegos
fan-c-fan by marco gallegos
3d_export
$10
fan
...fan
3dexport
a detailed fan designed for home or space blowing is now available for only 19.99!
turbosquid
$1
Fan
...fan
turbosquid
free 3d model fan for download as on turbosquid: 3d models for games, architecture, videos. (1427865)
turbosquid
$14
Fan
...fan
turbosquid
royalty free 3d model fan for download as on turbosquid: 3d models for games, architecture, videos. (1415642)
3ddd
$1
Светильник Fan
...светильник fan
3ddd
fan , italamp
светильник fan, производитель italamp
turbosquid
$25
Fan
...fan
turbosquid
royalty free 3d model fan for download as c4d on turbosquid: 3d models for games, architecture, videos. (1483246)
Better
3ddd
$1
Мозаика Better B-MOS D1
...os d1
3ddd
better , мозаика
мозаика better b-mos d1.
розтайленая мною.
+ бамп
+ рефлеккт
turbosquid
$19
BETTER THAN CHOCOLATE SOFA
... better than chocolate sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1144132)
3d_export
$5
Soviet Tank T-150
...t-150 3dexport simple tank model. in project texture are better ...
archive3d
free
Polycarbonate 3D Model
...polycarbonate plastic polycarbonate sheet a little bit oversized for better ...
3d_export
$20
Terminator
...a robot created by skynet to defeat the resistance. better watch the movie if you haven’t seen it...
3d_export
free
simple grass
...simple grass scene with procedural texture for grass, is better swaps the texture of grass by...
3d_export
$5
picture-mirror
...father,for the bath,it is desirable to make out of wood,better than...
3ddd
$1
APLLES with wood vase
...3ddd яблоко zip archive contain fbx model too, for better textures import to 3d software. kind...
3d_export
$5
vinyl record player
...size 295x260mm without any materials (just standart grey for better ...
3ddd
$1
Armchair 400
...armchair 400, designed by alvar aalto in 1936 and better known as tank. pelt coat idea by...