Thingiverse
Simple Mobius gimbal for X520 frame by Arakon
by Thingiverse
Last crawled date: 3 years ago
Update 20.02.2015:
New version with a different vibration damping approach here:http://www.thingiverse.com/thing:691553
Update 12.02.2015:
I added an "extended" version of both the arm and Mobius mount.
I realized that when installing a filter lens in front of the mobius, the weight of the filter is too much to balance the camera anymore. Now it can be slid further left and back to allow more adjustments.
Update 23.01.2015:
Mobius carrier updated again. Less support again, strengthened the top of the upper screw slit a bit, added a gap for certain larger USB plugs.
Camera is now meant to be slid into it straight (as opposed to angled), side supports are lengthened to give more hold for the camera and less chance to break after a few insertions. Front springy "nubs" were reduced in height to allow straight sliding.
Update 22.01.2015:
Updated the Mobius carrier to need less support when printing and slightly sturdier clips.
Update 17.01.2015:
Finally was able to try it out. I left the cam running while doing the initial setup of my rebuilt quadcopter.
Video is here: http://youtu.be/FjgQQuY5g3Q
This is what the copter does when running auto tune (not my video!):https://www.youtube.com/watch?v=zE-NJUlXxe8
Very simple gimbal that I made to fit the X520 "Alien" type frame. Works with the basic cheap china gimbal motors, 4x M3 back and 4x M2 front mounting holes. 9mm anti vibration balls needed.
Adjustable screw slots to balance the camera perfectly.
New version with a different vibration damping approach here:http://www.thingiverse.com/thing:691553
Update 12.02.2015:
I added an "extended" version of both the arm and Mobius mount.
I realized that when installing a filter lens in front of the mobius, the weight of the filter is too much to balance the camera anymore. Now it can be slid further left and back to allow more adjustments.
Update 23.01.2015:
Mobius carrier updated again. Less support again, strengthened the top of the upper screw slit a bit, added a gap for certain larger USB plugs.
Camera is now meant to be slid into it straight (as opposed to angled), side supports are lengthened to give more hold for the camera and less chance to break after a few insertions. Front springy "nubs" were reduced in height to allow straight sliding.
Update 22.01.2015:
Updated the Mobius carrier to need less support when printing and slightly sturdier clips.
Update 17.01.2015:
Finally was able to try it out. I left the cam running while doing the initial setup of my rebuilt quadcopter.
Video is here: http://youtu.be/FjgQQuY5g3Q
This is what the copter does when running auto tune (not my video!):https://www.youtube.com/watch?v=zE-NJUlXxe8
Very simple gimbal that I made to fit the X520 "Alien" type frame. Works with the basic cheap china gimbal motors, 4x M3 back and 4x M2 front mounting holes. 9mm anti vibration balls needed.
Adjustable screw slots to balance the camera perfectly.
Similar models
thingiverse
free
Gimbal for Mobius Action Cam with rotation Axis by Sternes
...ed version of the camera mount (lense of the camera is nearer to the roll axis)
added an angle mount, fits also for rctiger motor
thingiverse
free
Mini Flamewheel detachable Mobius mount by Arakon
...d of course.
also sand the small bumps at the front that hold the mobius at an angle, if you find it tough to get the camera out.
thingiverse
free
Mobius Gimbal by Xcopter
...t mounted gimbal for the mobius.
i am in the works of printing one right now so the photos above are not actually the real thing.
thingiverse
free
RCExplorer Tricopter V3 Tarot T-2D Gimbal Mount by carrera0to60
...ng except pointing the camera straight down. i am probably going to tweak the design further to try and gain a little more slack.
thingiverse
free
Mobius titled clean plate for Hoverthings Flip 260 by GizmotoFPV
...ly less tilt. i have gone back to the 10 degree plate as i am flying much faster now and the 10 matches my fpv camera tilt angle.
thingiverse
free
CR-10/10S Controller feet and 7" Tablet Bracket. by OldGaf
...t the usb (left 90 degree mico usb cable on order). i will be adding a camera mount and rpi case, as well as cable routing later.
thingiverse
free
vibration dampening gimbal holder by rubinkingma
... few mm clearance and also gives the driverboard for the gimbal a place.
alltogether not a bad build and it works like a charm!
thingiverse
free
Mobius Gimbal Plate for Simple Brushless Gimbal by mfilion
...ows for the mobius to be mounted with adjustment so that the weight is correct for the gimbal. it mimics the weight of the gopro.
thingiverse
free
SJCAM M10 Gimbal Mount by aelatik
...10 gimbal mount by aelatik
thingiverse
gimbal mount for sjcam m10 camera. i printed it on its back to use less support material.
thingiverse
free
Balanced Mobius Gimbal for FPV (DJI Mount) by Tomalinski
...tle protection against their sickly behavior.
btw: if you like my contributions and designs, feel free to send me a tip ... ;o)
X520
thingiverse
free
X520 Haube by Chris76
...
ich habe eine haube für mein x520 quadcopter entworfen. solle auch für "tbs" frame und "alien" passen!!!
;-)
thingiverse
free
Intel X520-DA2 10 Gigabit 10GBe SFP+ Dual Port Slot Bracket
... bracket
thingiverse
high profile slot bracket for intel x520-da2 10 gigabit 10gbe sfp+ dual port pcie card
very simple design
thingiverse
free
x520 FPV Camera Mount Sony Effio 700TVL 1/3 2.1mm by Tysonpower
...pv-hd-ultralight-camera-with-2_1mm-lens-ntscpla-for-fpv-rc-multicopter-p-1000385.html) and is quite okay for the realy low price.
thingiverse
free
X520 Mobius Gimbal v2 by Arakon
...nd file or sand the edges a litte bit.
loosely based on http://www.thingiverse.com/thing:688504, although by far not as pretty.
thingiverse
free
X520 Alien Frame GPS Tower by Arakon
...nd is only 50mm tall. i figured i'd throw it in for people who are fine with a lower tower or no external compass on the gps.
thingiverse
free
Large Volume 3D Printer by 3Dadicto
...volume 3d printer build volume of 300x300x400mm overall dimensions: x520y620-z640 built mainly with aluminum 20x20 and printed parts with...
grabcad
free
Turnigy AquaStar T20 3T 730KV/1280KV Water Cooled Brushless Motor
...730kv/1280kv water cooled brushless motor, also known as the x520 before hobbyking slaps their brand on it. the water-cooling...
Arakon
thingiverse
free
RCX H2205 wrench by Arakon
...rcx h2205 wrench by arakon
thingiverse
less hand shredding, more prop tightening. print at 70% or more infill for strength.
thingiverse
free
ZMR250 rear antenna + xt60 mount by Arakon
...ar antenna + xt60 mount by arakon
thingiverse
made by request, attempt #2.
completely untested.. let me know if it fits for you.
thingiverse
free
Mini Flamewheel 1806 Arms by Arakon
...fied to fit 1806 motors (2x12mm + 2x16mm).
also added a non-tested version with implemented nuttraps to make installation easier.
thingiverse
free
1541-II Floppy lock lever (Chinon mechanic) by Arakon
...1541-ii floppy lock lever (chinon mechanic) by arakon
thingiverse
modified floppy lock lever for 1541-ii with chinon mechanics.
thingiverse
free
Tiger MN2204 wrench by Arakon
...his together in sketchup. fits perfectly for me.
print at 100% infill for strength.
also fits the air gear 200 motors (2205).
thingiverse
free
Tweaker 180 front bumper lightweight by Arakon
...he bumper. i found it will stick in place nicely without needing the screws. if it does not, a drop of glue will take care of it.
thingiverse
free
Xbox 360 controller holder by Arakon
...tely into the base and added a small bit for the front that spreads the weight better and also makes them seat a lot more firmly.
thingiverse
free
Mini Flamewheel Hexacopter Plates by Arakon
...rcx 1804 motors and 10a escs.
the plates are fairly thick for additional stability. 30.5x30.5 and 45x45 mounting holes available.
thingiverse
free
110x motor shaft protector by Arakon
...ll.
the holes are meant to slip over screws so it can be seated properly. note that it may not fit if you use 4 screws per motor.
thingiverse
free
Antenna support for CL antenna by Arakon
...with a 42mm wire and 90° plug. sticks firmly on the plug end, single small zip tie secures the wire to stop it from slipping out.
Mobius
design_connected
$11
Mobius
...mobius
designconnected
kristalia mobius coffee tables computer generated 3d model. designed by lucidi pevere.
turbosquid
free
Mobius
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$120
Mobius bracelet
...mobius bracelet
3dexport
mobius bracelet 3d render modelling animation
3ddd
$1
Mobius Table
...mobius table
3ddd
kristalia , кофейный
mobius coffee table by kristalia
design_connected
$25
Mobius C
...mobius c
designconnected
zenith mobius c computer generated 3d model. designed by schamburg, marc.
3d_export
$5
mobius bracelet
...mobius bracelet
3dexport
3d model of a mobius bracelet.<br>modeled in solidworks.<br>rendered in keyshot.
turbosquid
$19
red mobius
...bosquid
royalty free 3d model red mobius for download as max on turbosquid: 3d models for games, architecture, videos. (1353147)
turbosquid
free
Mobius Desk
...y free 3d model mobius desk for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1229898)
turbosquid
$2
Mobius ring
...e 3d model mobius ring for download as 3ds, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1195725)
turbosquid
free
Mobius strip
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Gimbal
turbosquid
$1
Yuneec Save Stick for Gimbal
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$20
splashdrone gimbal camera
...nsions. all textures used have been included. thank you for purchasing this model!! click on my username to see more of my models
3d_export
$40
splashdrone 3 plus with gimbal camera
...nsions. all textures used have been included. thank you for purchasing this model!! click on my username to see more of my models
turbosquid
$88
DJI Phantom 2 Quadcopter with gimbal for GoPro HERO4 or 3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
concentrate box
...concentrate box 3dexport concealer box with handle and gimbal ...
cg_studio
$55
Drone Quadrocopter With Camera Rigged3d model
...fly wing propeller rc video camera sky dron spy gimbal gopro riged aircraft toy .obj .fbx .max .3ds -...
3d_ocean
$29
Drone Quadrocopter With Camera Rigged
...quadrocopter with camera rigged 3docean aircraft camera dron fly gimbal gopro propeller quadrocopter rc riged sky sport spy toy...
3ddd
free
Foucault's Iron Orb
...physicist léon foucault's gyroscope inspired our openwork globe. its double-gimbal frame is built of iron around a nucleus of...
thingiverse
free
Gimbal by tannermichael
...amera and gravity to self level. the gimbal uses .125" axles to pivot on. this gimbal was made using autodesk inventor 2015.
thingiverse
free
2020 Gimbal
...2020 gimbal
thingiverse
2020 gimbal
Frame
archibase_planet
free
Frame
...frame
archibase planet
frame photo frame
frame n190813 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Frame
...frame
archibase planet
frame photo frame
frame n071113 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Frame
...frame
3ddd
frame
3ddd
free
Frame
...frame
3ddd
frame
archibase_planet
free
Frame
...frame
archibase planet
frame mirror frame ornament
frame n260113 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Frame
...frame
archibase planet
frame photo frame
frame photo n190813 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Frame
...frame
archibase planet
frame window window frame
frame 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Frame
...frame
archibase planet
frame window frame window
frame 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Frame
...frame
archibase planet
frame wall frame decoration
frame 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Frame
...frame
archibase planet
frame window window frame
frame 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Simple
turbosquid
$1
Simple goblet (Taca simples)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
simple bench
...simple bench
3dexport
the simple bench which can be used in simple projects or video-games.
3d_export
$5
simple knob
...simple knob
3dexport
simple knob
3d_export
$5
simple handle
...simple handle
3dexport
simple handle
3d_export
$5
simple button
...simple button
3dexport
simple button
3d_export
$5
simple spindle
...simple spindle
3dexport
simple spindle
3d_export
$5
simple wheel
...simple wheel
3dexport
simple wheel
3d_export
$5
simple chair
...simple chair
3dexport
simple blue chair
3d_export
free
Simple room
...simple room
3dexport
here is a simple but beautiful room
3ddd
free
SIMPLE | Кресло
...io cianfarra , simple
производитель area declic дизайн giulio cianfarra коллекция simple