Thingiverse
Servo driven nozzle wiper arm by ProtomakerSprint
by Thingiverse
Last crawled date: 3 years, 1 month ago
Servo driven nozzle wiper arm.
Servo HiTec HS311 on RAMPS 1.4
Nozzle cleaner wiper improved. Servo to move 3D Printed arm that wipe ooze from the nozzle Wire Brush to make it work a lot better :
Nozzle cleaner wiper improved. Servo driven. 3D Printinghttps://youtu.be/lwQ_tgOPKMM
eBay : 6 Pieces Brass Wire Brush Set for Cleaning Welding Slag and Rust Q2L5 https://www.ebay.co.uk/itm/28295962126
STILL OOZING ISSUE For me!!! Fixed with wire brush see video abovehttps://www.youtube.com/watch?v=TltG8CB8cbI
Started a full actual 3D print. This FAILED for me, ( Fixed with wire brush see video above
), because even though it wiped my E3D v6 "Clone" nozzle clean the nozzle started to ozze quite significantly after the cleaning using this the Servo driven nozzle wiper arm method and that was even though I asked for an initial wiped of the nozzle and another wipe clean the nozzle after the Auto-Levelling routine.
I most likely need a "real" E3D v6 and not the clone that I am using or/and try to print at a lower temperature than the 245 I am using for ABS.
Servo driven nozzle wiper arm Good or Bad Fixed with wire brush see video above
https://www.youtube.com/watch?v=ia_PXwgTess&index=5&list=PLUqt0sTiXUDeZBzcgukIvN0AP9FGhKBbD
Servo driven nozzle wiper arm Testing odd, I believe issue I have are due to trying to directly supply power from the Servo port on the RAMPS board, this may not have enough power to control this Servo HS 311 reliably.https://youtu.be/QG8h34WXnKs
The "Extra tray Servo driven nozzle wiper arm.stl" is to acetone on to the single tray version if you want to.. For wiping both forward and backwards and trying to catch filament in.
Generally the oozed filament catches on to the Silicon Brush. A Wire brush is a lot better Fixed with wire brush see video above. When the wiper arm moves to its forward parked position it may be removed.
RAMPS does no seem to be able to reliably power this HS311 Servo. It may be best to generate your own 5V rail, (7805) from 12V. The RAMPS 5V rail doesnt really have enough power (causes the servo the twitch), which happens to me some times, well acting odd rebooting RAMPS, not running G-Gode in sequence, etc.... when pluging the HS311 Servo directly into the RAMPS board, even if 5 Volts is taken from vcc RAMPS Power
Please Note: The Bracket for the HS311 Servo will most likely not be suitable your 3D Printer, the mounting holes and support arms are good for the HS 311 Servo.
Hitec HS311 Servo
Motor Type: Reliable Three-Pole Ferrite Motor
Bearing Type: None
Speed (4.8V/6.0V): 0.19 / 0.15 sec @ 60 deg.
Torque oz./in. (4.8V/6.0V): 42 / 51
Torque kg./cm. (4.8V/6.0V): 3.0 / 3.7
Size in Inches: 1.57 x 0.78 x 1.43
Size in Millimeters: 39.88 x 19.81 x 36.32
Weight ounces: 1.51 Weight grams: 42.81
I did have issues, but none seen in my latest test, include resetting RAMPS at different positions when the arm move to clean the nozzle... *
When the 3D Printer, RAMPS, is first powered on the servo moving about 10°, I move to a Park position in my G-code, below.
Maybe not enough Amps direct from the RAMPS board. Reading up suggest this is the case and the Servos should be powered from a separate 5 Volt supply.
Extra infomation Marlin Wipe Nozzle command, the above uses G-Code to move the wiper arm and not the Marlin Wipe Nozzle command which may use 3D printer real estase.
define NOZZLE_CLEAN_FEATURE
Clean Nozzle Feature -- EXPERIMENTAL
Adds the G12 command to perform a nozzle cleaning process.
Added "Servo driven nozzle double wiper arm" this has a small extra tray to catch filament if you wish to wipe in the other direction as well.
This is a Remix, with a BIG Thank You, of:-
Servo driven nozzle wiper arm for delta printers
by fjohn624, published Aug 6, 2015https://www.thingiverse.com/thing:958642
G-Code I used. Note you will to change this, it is just a basic to get you started.
Setting Nozzle Height will need changing for your 3D printer and wiper are heights, etc.
This is a different G-Code movement method to the original, (by by fjohn624), which may be much, much better than mine below. I need to do more testing.
For example adding a purge some filament into the wiper tray and retraction...
Uses a Servo under G-Code, in Start G-Gode of 3D printing to move an arm with a piece of silicon attached to clean ooze, Silicon Brush, a Wire brush maybe better, from the Hot End nozzle, (a wire brush may be better, example https://youtu.be/y3l7kjuVhro ).
; Servo Nozzle Clean Test
; Message
M117 Servo Nozzle Clean Test
G21 ; set units to millimeters
G90 ; use absolute coordinates
; Make sure Wiper Arm is Parked forward at the front of the printer out of the way
M280 P1 S 180
; Home all axes. Note No heat
; Will move to center for BLTouch Smart Probe
G28
; Move Z Up to to Nozzle Wipe Height.
; Place the Nozzle in the correct Z position for wiping
; NOTE the Wiper Silicon piece should only just scrape the top edge against the Nozzle
; Any higher and the wiper arm, Wiper Silicon piece, may jam against the Nozzle causing the 3D printer to reboot
G1 Z 48.00 F2500
; Home X. Place the Nozzle in the correct X position for wiping
G28 X
; Purging Filament part
; Move Wiper Arm just before wiping the nozzle
; This place the Tray on the wiper arm bebow the nozzle
; Ready to catch any ooze as the nozzle heats up
M280 P1 S40
; #######################################################
; Heating Starting would go here. Wait for Temperature
; #######################################################
; Set extruder Temperature (waits till reached). 245 is my normal ABS hot end setting
M109 S245
; Reset Extuder. Any pervious feeding may cause the feeder to feed backwards otherwise
; G92 Ennn new extruder position
G92 E0
; Feed Filament 10mm into the Wiper Tray to Purge the nozzle
G1 E 10 F300
; Pause for four second to wait any ooze from purge
; Dwell command millisconds G4 P60000 is one minute
G4 P4000
; Retraction 2mm Recommended Maximun for E3D v6. To try to stop any ooze
G1 E -2 F300
; Pause for one more second after Retraction to wait any ooze from purge
; Dwell command millisconds G4 P60000 is one minute
G4 P1000
; Move Wiper Arm just after the nozzle. This will actually wipe the nozzle.
; NOTE: 25 is the Maximun able to move, close to the Threaded Rods, etc...
M280 P1 S 25
; Pause for wiper to move, half a second
; Dwell command millisconds G4 P60000 is one minute
G4 P500
; Move Z Up move the Nozzle above the Wipe Height ready to move back to park position
G1 Z 60.00 F2500
; Pause for 2 seconds to wait for the printer nozzle to move up, above command, before moving the wiper arm back to it's park position
; Dwell command millisconds G4 P60000 is one minute
G4 P2000
; Move Wiper Arm to Parked forward at the front of the printer out of the way
M280 P1 S180
; Pause for wiper to move, half a second
; Dwell command millisconds G4 P60000 is one minute
G4 P500
; Finished Servo Nozzle Clean Test
; Message
M117 End Servo Nozzle Clean Test
; Doing some X carrage movements to simulate 3D printing
; Make sure it has not tripped, reset the RAMPS, etc
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
Servo HiTec HS311 on RAMPS 1.4
Nozzle cleaner wiper improved. Servo to move 3D Printed arm that wipe ooze from the nozzle Wire Brush to make it work a lot better :
Nozzle cleaner wiper improved. Servo driven. 3D Printinghttps://youtu.be/lwQ_tgOPKMM
eBay : 6 Pieces Brass Wire Brush Set for Cleaning Welding Slag and Rust Q2L5 https://www.ebay.co.uk/itm/28295962126
STILL OOZING ISSUE For me!!! Fixed with wire brush see video abovehttps://www.youtube.com/watch?v=TltG8CB8cbI
Started a full actual 3D print. This FAILED for me, ( Fixed with wire brush see video above
), because even though it wiped my E3D v6 "Clone" nozzle clean the nozzle started to ozze quite significantly after the cleaning using this the Servo driven nozzle wiper arm method and that was even though I asked for an initial wiped of the nozzle and another wipe clean the nozzle after the Auto-Levelling routine.
I most likely need a "real" E3D v6 and not the clone that I am using or/and try to print at a lower temperature than the 245 I am using for ABS.
Servo driven nozzle wiper arm Good or Bad Fixed with wire brush see video above
https://www.youtube.com/watch?v=ia_PXwgTess&index=5&list=PLUqt0sTiXUDeZBzcgukIvN0AP9FGhKBbD
Servo driven nozzle wiper arm Testing odd, I believe issue I have are due to trying to directly supply power from the Servo port on the RAMPS board, this may not have enough power to control this Servo HS 311 reliably.https://youtu.be/QG8h34WXnKs
The "Extra tray Servo driven nozzle wiper arm.stl" is to acetone on to the single tray version if you want to.. For wiping both forward and backwards and trying to catch filament in.
Generally the oozed filament catches on to the Silicon Brush. A Wire brush is a lot better Fixed with wire brush see video above. When the wiper arm moves to its forward parked position it may be removed.
RAMPS does no seem to be able to reliably power this HS311 Servo. It may be best to generate your own 5V rail, (7805) from 12V. The RAMPS 5V rail doesnt really have enough power (causes the servo the twitch), which happens to me some times, well acting odd rebooting RAMPS, not running G-Gode in sequence, etc.... when pluging the HS311 Servo directly into the RAMPS board, even if 5 Volts is taken from vcc RAMPS Power
Please Note: The Bracket for the HS311 Servo will most likely not be suitable your 3D Printer, the mounting holes and support arms are good for the HS 311 Servo.
Hitec HS311 Servo
Motor Type: Reliable Three-Pole Ferrite Motor
Bearing Type: None
Speed (4.8V/6.0V): 0.19 / 0.15 sec @ 60 deg.
Torque oz./in. (4.8V/6.0V): 42 / 51
Torque kg./cm. (4.8V/6.0V): 3.0 / 3.7
Size in Inches: 1.57 x 0.78 x 1.43
Size in Millimeters: 39.88 x 19.81 x 36.32
Weight ounces: 1.51 Weight grams: 42.81
I did have issues, but none seen in my latest test, include resetting RAMPS at different positions when the arm move to clean the nozzle... *
When the 3D Printer, RAMPS, is first powered on the servo moving about 10°, I move to a Park position in my G-code, below.
Maybe not enough Amps direct from the RAMPS board. Reading up suggest this is the case and the Servos should be powered from a separate 5 Volt supply.
Extra infomation Marlin Wipe Nozzle command, the above uses G-Code to move the wiper arm and not the Marlin Wipe Nozzle command which may use 3D printer real estase.
define NOZZLE_CLEAN_FEATURE
Clean Nozzle Feature -- EXPERIMENTAL
Adds the G12 command to perform a nozzle cleaning process.
Added "Servo driven nozzle double wiper arm" this has a small extra tray to catch filament if you wish to wipe in the other direction as well.
This is a Remix, with a BIG Thank You, of:-
Servo driven nozzle wiper arm for delta printers
by fjohn624, published Aug 6, 2015https://www.thingiverse.com/thing:958642
G-Code I used. Note you will to change this, it is just a basic to get you started.
Setting Nozzle Height will need changing for your 3D printer and wiper are heights, etc.
This is a different G-Code movement method to the original, (by by fjohn624), which may be much, much better than mine below. I need to do more testing.
For example adding a purge some filament into the wiper tray and retraction...
Uses a Servo under G-Code, in Start G-Gode of 3D printing to move an arm with a piece of silicon attached to clean ooze, Silicon Brush, a Wire brush maybe better, from the Hot End nozzle, (a wire brush may be better, example https://youtu.be/y3l7kjuVhro ).
; Servo Nozzle Clean Test
; Message
M117 Servo Nozzle Clean Test
G21 ; set units to millimeters
G90 ; use absolute coordinates
; Make sure Wiper Arm is Parked forward at the front of the printer out of the way
M280 P1 S 180
; Home all axes. Note No heat
; Will move to center for BLTouch Smart Probe
G28
; Move Z Up to to Nozzle Wipe Height.
; Place the Nozzle in the correct Z position for wiping
; NOTE the Wiper Silicon piece should only just scrape the top edge against the Nozzle
; Any higher and the wiper arm, Wiper Silicon piece, may jam against the Nozzle causing the 3D printer to reboot
G1 Z 48.00 F2500
; Home X. Place the Nozzle in the correct X position for wiping
G28 X
; Purging Filament part
; Move Wiper Arm just before wiping the nozzle
; This place the Tray on the wiper arm bebow the nozzle
; Ready to catch any ooze as the nozzle heats up
M280 P1 S40
; #######################################################
; Heating Starting would go here. Wait for Temperature
; #######################################################
; Set extruder Temperature (waits till reached). 245 is my normal ABS hot end setting
M109 S245
; Reset Extuder. Any pervious feeding may cause the feeder to feed backwards otherwise
; G92 Ennn new extruder position
G92 E0
; Feed Filament 10mm into the Wiper Tray to Purge the nozzle
G1 E 10 F300
; Pause for four second to wait any ooze from purge
; Dwell command millisconds G4 P60000 is one minute
G4 P4000
; Retraction 2mm Recommended Maximun for E3D v6. To try to stop any ooze
G1 E -2 F300
; Pause for one more second after Retraction to wait any ooze from purge
; Dwell command millisconds G4 P60000 is one minute
G4 P1000
; Move Wiper Arm just after the nozzle. This will actually wipe the nozzle.
; NOTE: 25 is the Maximun able to move, close to the Threaded Rods, etc...
M280 P1 S 25
; Pause for wiper to move, half a second
; Dwell command millisconds G4 P60000 is one minute
G4 P500
; Move Z Up move the Nozzle above the Wipe Height ready to move back to park position
G1 Z 60.00 F2500
; Pause for 2 seconds to wait for the printer nozzle to move up, above command, before moving the wiper arm back to it's park position
; Dwell command millisconds G4 P60000 is one minute
G4 P2000
; Move Wiper Arm to Parked forward at the front of the printer out of the way
M280 P1 S180
; Pause for wiper to move, half a second
; Dwell command millisconds G4 P60000 is one minute
G4 P500
; Finished Servo Nozzle Clean Test
; Message
M117 End Servo Nozzle Clean Test
; Doing some X carrage movements to simulate 3D printing
; Make sure it has not tripped, reset the RAMPS, etc
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
G1 XO Y0 F12500 ; Left
G1 X245 Y0 F12500 ; Right
Similar models
thingiverse
free
Rostock MAX purge area/nozzle cleaner by npushis
... brush holder to catch purged material and wipe nozzle clean before printing. part_b is removable to allow for full bed printing.
thingiverse
free
Ender 3 Nozzle Wiper by Imagineer_NL
...
( https://www.amazon.com/pieces-brass-brush-cleaning-welding )
youtube video of the wiping process: https://youtu.be/bburromzb4q
thingiverse
free
Ender 3/Pro Ender5/Pro Bed Nozzle Brush by blindley125
...1 z10.0 f3000 ; move z axis up little to prevent scratching of heat bed
g1 x8 y20 z0.3 f5000.0 ; move over to prevent blob squish
thingiverse
free
Geeetech i3 Pro B extruder wiper by Damien68
...0 ;zero the extruded length
g1 f200 e3 ;extrude 3mm of feed stock
g92 e0 ;zero the extruded length again
g1 f9000
m117 printing ;
thingiverse
free
Ender 3 V2 Brush mount by SharpSeer
...ed
g1 x5 y20 z0.3 f5000.0 ; move over to prevent blob squish
lastly, rotate the print till it is flat, i have not altered it yet.
thingiverse
free
Geeetech A10t Purge Bucket with removable bucket by 123TaDa
...ipe
g0 x0 f2000 ; return
m211 s1 ; turn on soft stops once more
g1 e-0.5 ; try to prevent pips
g92 e0
; start extruder script end
thingiverse
free
Upgraded WEEDO X40 Mounted Purge Bucket by ute
...ucket setup for the weedo x40 idex printer. it uses the original brush and mounting points.
mirror and print for the right side.
thingiverse
free
ANET A8 Nozzle Filament Wiper - Cleaner - Updated by andy_spoo
...
g1 y50 f3000 ; move out of the way of wiper
g;; 1 x10 y10 f3000; back to 'near' front left
g92 e0; zero extruder
; *****
thingiverse
free
Silicone Wiper - Purge Bucket with removable tray (Artist-D) by yydoctt
...factor. this is my ideamaker script, i have a similar one for prusaslicer, i am running a custom setup...
thingiverse
free
SVO2 Purge Bucket and GCODE by RedSquirrelHobbies
... positioning on
g1 z-1 f1000 ; lower nozzle by 1mm
g90 ; absolute positioning on
m400 ; wait for finish
Protomakersprint
thingiverse
free
Marlin Inside Symbol by ProtomakerSprint
...marlin inside symbol by protomakersprint
thingiverse
marlin inside symbol
thingiverse
free
Octoprint Raspberry Pi Logo by ProtomakerSprint
...octoprint raspberry pi logo by protomakersprint
thingiverse
octoprint raspberry pi logo
thingiverse
free
Pie Shaped Piece curved wedge by ProtomakerSprint
...pie shaped piece curved wedge by protomakersprint
thingiverse
pie shaped piece curved wedge
thingiverse
free
Ribbon Cable Holder 2040 by ProtomakerSprint
...ribbon cable holder 2040 by protomakersprint
thingiverse
just ribbon cable holder 2040
e.g. pi camera cable holder
thingiverse
free
Humidity Removal Unit by ProtomakerSprint
...ld do.
humidity removal unit 3d print playlist on youtubehttps://www.youtube.com/playlist?list=pluqt0stixuddi0rbgkrowhanr9h22nuva
thingiverse
free
PCB Runner clips by ProtomakerSprint
... having quite a good grip.
ideal if need to adjust pcb edge distance away from something else.
single and doubles, adjust to fit.
thingiverse
free
SD Card Holder by ProtomakerSprint
...ndard +10 microhttps://youtu.be/jpvzpjpw_cu
remix of : sd card holderhttps://www.thingiverse.com/thing:2722882 by theswedishbear
thingiverse
free
Save the NHS by ProtomakerSprint
...op the new plans to dismantle our nhs. please share it.https://you.38degrees.org.uk/petitions/stop-the-plans-to-dismantle-our-nhs
thingiverse
free
Flux Thermal Paste Dispenser 3D Print by ProtomakerSprint
... raft
baised on dispenser for syringe of flux or solder paste by mordaha on thingiverse:https://www.thingiverse.com/thing:4549023
thingiverse
free
Motorola Moto G 3rd generation Tripod Mount by ProtomakerSprint
...g 3rd generation tripod mount
should suite any bigger backed phones
a video of this being 3d printed
https://youtu.be/qwuess8shqc
Wiper
turbosquid
$60
wipers
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$9
Wiper
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Wipers 3D Model
...wipers 3d model
3dexport
wipers 3d model zarko 72473 3dexport
3d_export
$10
Floor Wiper 3D Model
...floor wiper 3d model
3dexport
wiper
floor wiper 3d model ankush2211 52516 3dexport
turbosquid
$6
3D car Wiper
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Volvo XC90 Rear Wiper Mechanism
...volvo xc90 rear wiper mechanism
3dexport
gear gear for volvo xc90 rear wiper
cg_studio
$5
Wipers Alca for car3d model
...d model
cgstudio
.3ds .max .obj - wipers alca for car 3d model, royalty free license available, instant download after purchase.
turbosquid
$35
Front Windscreen Wiper Set
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
cg_studio
$45
Wiper with transmission and drive unit3d model
...c4d .lwo .obj - wiper with transmission and drive unit 3d model, royalty free license available, instant download after purchase.
3d_export
$8
rear window wiper drive gear land rover freelander and fordfusion
...per drive gear land rover freelander and fordfusion
3dexport
rear window wiper drive gear land rover freelander and ford_fusion.
Driven
turbosquid
$50
CHAIN DRIVEN CONVEYOR
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
free
driven shaft of the lump crusher
...driven shaft of the lump crusher
3dexport
3d_export
$27
n95 full servo driven mask printer
...n95 full servo driven mask printer
3dexport
n95 full servo driven mask printer
turbosquid
$16
(Project) Food packing helper machine with holding clamp and press table driven by an actuator
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$47
the fifth generation of one driven two new mask machine
...ing, lamination, pressing, ear band tapping, ultrasonic, etc. the structure of the model is detailed, including model parameters.
3d_export
$15
industrial belt-driven air cooler
...leaning up necessary, just drop your models into the scene and start rendering/texturing. no special plugin needed to open scene.
3d_export
free
golf cart
...golf cart 3dexport golf cart for golfers to be driven in...
3d_export
$10
design and assembly of pulley
...pulley 3d model which is used for drive and driven ...
archive3d
free
Windmill 3D Model
...windmill 3d model archive3d wind turbine wind-driven powerplant wind-electric set windmill n181208 - 3d model (*.gsm+*.3ds)...
3d_export
$30
Compressed Air Engine 3D Model
...motor flywheel shaft camshaft piston valve block engineering compressed-air driven compressed air engine 3d model zenmunster 92451...
Servo
turbosquid
$30
Servo
...d model servo for download as obj, blend, dae, stl, and sldpr on turbosquid: 3d models for games, architecture, videos. (1394011)
3d_export
$5
servo motor
...tor
3dexport
it's a simple part of servo motor 0.75kw for used in machines assembly to show specified motor in own project.
turbosquid
$1
Servo Moter
...quid
royalty free 3d model servo moter for download as blend on turbosquid: 3d models for games, architecture, videos. (1650816)
turbosquid
free
Motor/Servo
...osquid
royalty free 3d model motor/servo for download as obj on turbosquid: 3d models for games, architecture, videos. (1522522)
turbosquid
$60
Servo Skull
...
royalty free 3d model servo skull for download as ma and fbx on turbosquid: 3d models for games, architecture, videos. (1318573)
3d_export
$5
Servo 3D Model
...rvo 3d model
3dexport
servo
servo 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl pasqualesiciliano 104590 3dexport
turbosquid
$50
Servo Motor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$49
Servo Motor
...model servo motor for download as 3ds, max, obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1324153)
turbosquid
$29
Servo Set
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
machine servo
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Nozzle
3d_export
$5
nozzle
...nozzle
3dexport
3d_export
$49
fuel nozzles
...fuel nozzles
3dexport
fuel nozzles 3d model. include max, obj, fbx files.
archive3d
free
Nozzle 3D Model
...archive3d
nozzle hair-drier ware
nozzle - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$25
Pirouette Nozzle
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Fuel Nozzle
...model fuel nozzle for download as c4d, fbx, obj, 3ds, and stl on turbosquid: 3d models for games, architecture, videos. (1672732)
turbosquid
$8
Aeration Nozzles
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
laval airjet nozzle
...laval airjet nozzle
3dexport
a simple modified laval nozzle (airjet shooter) for sorting purposes.
3d_export
$36
Gas nozzle 3D Model
... 3d model
3dexport
gas pump nozzle dispenser filling station petrol fuel spout tank gun
gas nozzle 3d model tartino 1945 3dexport
turbosquid
$10
Diecast Jet nozzle
... free 3d model diecast jet nozzle for download as obj and stl on turbosquid: 3d models for games, architecture, videos. (1425990)
turbosquid
$39
Rocket nozzle, supressor.
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Arm
archibase_planet
free
Arm
...ase planet
arm hand right hand skeleton
arm human skeleton right arm n030515 - 3d model (*.gsm+*.3ds+*.max) for 3d visualization.
3ddd
$1
arm chair
...arm chair
3ddd
arm chair , пуф
arm chair
turbosquid
$5
arm
...arm
turbosquid
royalty free 3d model arm for download as obj on turbosquid: 3d models for games, architecture, videos. (1306158)
turbosquid
free
Arm
...arm
turbosquid
free 3d model arm for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1346955)
turbosquid
$29
Arm
...osquid
royalty free 3d model arm for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1382436)
3d_export
$5
coat of arms
...coat of arms
3dexport
coat of arms
3ddd
$1
ARM SOFA
...arm sofa
3ddd
arm sofa
3ddd
$1
Arm chair
...arm chair
3ddd
arm chair
3ddd
$1
Arm chair
...arm chair
3ddd
угловое
arm chair
3ddd
$1
ARM CHAIR
...arm chair
3ddd
arm chair clothes