Thingiverse
Sequential Shifter Simracing (no Electronics) by davebrave
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is my "heavy duty" sequential shifter for simracing. It's based on a ball bearing that is pushed against two microswitches. I have not included electronics in the design but you can use an Arduino Micro pro (with USB support) or even use an old gamepad and solder the two microswitches directly to the board.
There are two diferent levers for a shorter or longer grip.
Materials:
1x 6000 ZZ ball bearing
2x 626 zz ball bearing (optional)
2x 55mm springs
2x 20mm microswitch on-off 3-pin
Screws, nuts and washers:
m4 2x 20mm
m5 2x 35mm, 5x 45mm
m6 2x 35mm, 2x45, 1x55mm
Print:
20% infill
0.2 and 4 wall lines.
Although it's not crucial, you should have the XY expansion properly adjusted so holes have the right size.
Assembly:
It should be quite straight forward:
You start with left_base, screw both switch holders using m4 screws and nuts. Solder the cables before installing the switches. They are just pushed into the holder.
Screw the right_base and insert the m5 55mm screw that is going to be used for the springs.
Insert the 2 ball bearings into the lever. You can choose either short or longer lever. Alternatively, you can use the dummy bearings instead, but I haven't tried myself. Put a m6 screw through the base and the lever.
The push arm is quite simple but pay attention to the springs, they both form a "V" on each side, so you mount the springs in different angles but sharing the same base point. Look at the assembly pictures for more clarification.
Then you can use the remaining holes to attach the shifter to your rig using m8 or m6 depending on your needs.
Enjoy!
There are two diferent levers for a shorter or longer grip.
Materials:
1x 6000 ZZ ball bearing
2x 626 zz ball bearing (optional)
2x 55mm springs
2x 20mm microswitch on-off 3-pin
Screws, nuts and washers:
m4 2x 20mm
m5 2x 35mm, 5x 45mm
m6 2x 35mm, 2x45, 1x55mm
Print:
20% infill
0.2 and 4 wall lines.
Although it's not crucial, you should have the XY expansion properly adjusted so holes have the right size.
Assembly:
It should be quite straight forward:
You start with left_base, screw both switch holders using m4 screws and nuts. Solder the cables before installing the switches. They are just pushed into the holder.
Screw the right_base and insert the m5 55mm screw that is going to be used for the springs.
Insert the 2 ball bearings into the lever. You can choose either short or longer lever. Alternatively, you can use the dummy bearings instead, but I haven't tried myself. Put a m6 screw through the base and the lever.
The push arm is quite simple but pay attention to the springs, they both form a "V" on each side, so you mount the springs in different angles but sharing the same base point. Look at the assembly pictures for more clarification.
Then you can use the remaining holes to attach the shifter to your rig using m8 or m6 depending on your needs.
Enjoy!
Similar models
thingiverse
free
Gearbox Hanger for 20mm Extrusions
...o the gearbox before assembling to the extrusion. if done in the opposite order, it will be impossible to place the top m6 screw.
thingiverse
free
Dual Extruder by Psycho1981
...ng:
4x allen screw m5
4x square nut m5
4x washer m5
electronic:
-ramps 1.4 board
-atx power supply
-firmware "marlin"
thingiverse
free
TH8RS Sequential Shifter mod
...ed: 20mm 7.5mm * 1.2mm (https://tinyurl.com/s4sbl6c)
original concept by dukethirteen: https://www.thingiverse.com/thing:3406574
thingiverse
free
Custom Spring Shifter by Gianotto
...spring diameter: 7.5mm
bolts (per shifter):
1x m5 25mm (lever)
2x m3 8mm (paddle)
2x m3 15mm to fix into the steering wheel case.
thingiverse
free
Paddle shifter by annttu
...ww.thingiverse.com/thing:4706673 but can be attached to other mounts too.
assembly instruction video https://youtu.be/-902n7sj2le
thingiverse
free
Sequential shifter
...50 mm screw
4x m3 nut
8x m3 washer
2x foam rubber 28x25x20 mm
2x m6 15 mm wood screw
2x micro switch 16a 30x15x10 mm
wire 3 m
thingiverse
free
Calspinner the fast handspinner by FRED67X
...rse
this fidget spinner only needs :
1x 608 zz ball bearing, use wd40 for make it faster !
6x m5 20mm screw
6x m5 nuts (or 12x).
thingiverse
free
IEC320-C14 3030 mount by montematico
... hammer nuts
print face down
required materials
2x m4 screws
2x m4 nuts
1x iec320-c14 recectacle
2x m5 screws
2x m5 hammer nuts
thingiverse
free
Sequential shifter by T-Fork
...ith a max width of 2 cm or 2x magnets and two hall effect sensors (https://www.amazon.de/dp/b07dpvtkbb?ref_=ast_sto_dp&th=1)
thingiverse
free
Sequential shifter for sim racing
...ider and the threaded rod.
electronics wise use whatever you like, you can use an arduino board, teensy, leo bodnar boards, etc.
Davebrave
thingiverse
free
Ninco Slot track inner curve border by davebrave
...an print it at 10% infill and in your prefered material and 0.2 to 0.3 layer height. i chose abs just for the colour and finish.
thingiverse
free
QuickRelease for T500/T300 Steering Wheel base by davebrave
... layer adhesion than abs like petg. or if you use abs, make sure that the settings allow the best layer adhesion you can achieve.
Simracing
thingiverse
free
boite a bouton simracing by PixL36100
...boite a bouton simracing by pixl36100
thingiverse
boite a bouton simracing
thingiverse
free
Officechair Blockbrakes for Simracing by the_lone_Nomad
...blockbrakes for simracing by the_lone_nomad
thingiverse
two blocks to put under an officechair to lock it in place for simracing
thingiverse
free
Handbrake Simracing by Javi91ac
...handbrake simracing by javi91ac
thingiverse
work in progress
thingiverse
free
Button Box Simracing by ImHyp3D
...simracing by imhyp3d
thingiverse
a 21 button box for simracing
not print tested yet
maybe you can test it and give me criticism
thingiverse
free
Simracing Labels by Fred2112
...112
thingiverse
the size are for popular plastic button find on aliexpress.
ajust the size for your button.
i use tac if nedded.
thingiverse
free
VoCore / USBD480 Simracing Dash by denned
... remix without leds!
check out original by morguux: https://www.thingiverse.com/thing:4535313
also check out original for mounts.
thingiverse
free
Simracing Dashboard by simersion
...mersion
thingiverse
dashboard for 4.3" nextion display, arduino micro and 16x 5mm leds
feel fre to contact me for more info
thingiverse
free
Dashboard for simracing CSL by Pekpo96
...dashboard for simracing csl by pekpo96
thingiverse
remix made for fanatec csl wheel. distance between legs 55mm (midcenter).
thingiverse
free
HandBrake Handle (Simracing) by AtoMic09
...?ie=utf8&psc=1
i have used epoxy to firmly join together the 2 covers.
.step included. feel free to modify it. post results !
thingiverse
free
Headphone holder simracing-rig by storemaster
...headphone holder simracing-rig by storemaster
thingiverse
a simple headphone mount for my sim-racing rig
Sequential
thingiverse
free
Sequential Gearbox by NateTG
...tg
thingiverse
constant mesh sequential gearbox using emmet's gear bearings. i need to work out how to make it printable...
thingiverse
free
Sequential shifter
...50 mm screw
4x m3 nut
8x m3 washer
2x foam rubber 28x25x20 mm
2x m6 15 mm wood screw
2x micro switch 16a 30x15x10 mm
wire 3 m
thingiverse
free
Sequential expanding mechanism box by Frolgo
...o
thingiverse
this is a nice box with a twist. to open the upper lid has to be turned. then the three leavers expand sequential.
thingiverse
free
TH8 SEQUENTIAL KNOB by Fox_85
...th8 sequential knob by fox_85
thingiverse
this is my thrustmaster th8 secuantial knob
thingiverse
free
Sequential Shifter bracket for Logitech G27 by TacosForJesus
...
slips on the mounting knobs and secured with elastics to pull the lever out of gear in order to use it as a sequential shifter.
thingiverse
free
sequential shifter MOD g27 by elgh33
...t + right model
makes the gated to sequential shifter inspired by madlap but made with 100% own measurements from the g27 shifter
thingiverse
free
Weighted Sequential Shift Knob by E_Elisio
... fanatec clubsport ssq shifter. has a slot to fit a 3/4" x 2" bolt and x3 hex nuts of the same size to act as a weight.
thingiverse
free
Sim Racing Sequential Shifter upgrade by clos2727
...stant stress applied all parts sjould be printed at 100% infill.
except for switch cover.
filament used for this project is pla.
thingiverse
free
Sequential Shifter DIY SIM RIG by DrBrauch
...n pic) to make shaft stand and make sequential feel great.
need 5 long bolt
for shaft prefer change to stainless steel shaft 10mm
thingiverse
free
SSH Shifter Sequential clip-on Plate
...st clip on an existing plate by holding on original plate screws. it's two parts so you do not have to remove the shift knob.
Shifter
thingiverse
free
shifter plates for a shifter im making by stockcar
...shifter plates for a shifter im making by stockcar
thingiverse
making a shifter for online racing.
thingiverse
free
Skull Shifter by ColeDowns
...skull shifter by coledowns
thingiverse
just a shifter
thingiverse
free
Bicycle shifter by Rumble89
...bicycle shifter by rumble89
thingiverse
shifter for a hub circuit.
thingiverse
free
Playseat Shifter Holder
...playseat shifter holder
thingiverse
playseat shifter holder
thingiverse
free
H-Shifter / Vites
...h-shifter / vites
thingiverse
h-shifter model
thingiverse
free
Shifter for audi A3
...shifter for audi a3
thingiverse
shifter for audi a3
thingiverse
free
SHIFTER SRAM SUPPORT
...shifter sram support
thingiverse
shifter sram support
thingiverse
free
pommeau shifter logitech
...pommeau shifter logitech
thingiverse
pommeau shifter logitech
thingiverse
free
Shifter by boyleengineering
...shifter by boyleengineering
thingiverse
thingiverse
free
Round Knob Shifter
...round knob shifter
thingiverse
knob shifter for car models
Electronics
thingiverse
free
Electron by RikerLansdale
...electron by rikerlansdale
thingiverse
an electron to go on the electron ring
thingiverse
free
Electronics box
...onics box
thingiverse
electronics box
electronics box for ip camera mount for ender 3.
https://www.thingiverse.com/thing:4086651
thingiverse
free
electronic load
...electronic load
thingiverse
electronic load. maximum load 100v. 75w
thingiverse
free
Electronic Box
...electronic box
thingiverse
electronic box. arimf muffle furnace controller. no screw design.
thingiverse
free
Electronics enclosure
...electronics enclosure
thingiverse
a box that i plan to use for some of my electronics - still work in progress.
thingiverse
free
Electronics box for misc electronics by brfields44
... / electronics box. drill your holes for your wires to make it custom. i can also make changes if you need them. just message me.
thingiverse
free
electronic sructure by Phokas
...electronic sructure by phokas
thingiverse
electronic structure
thingiverse
free
Electronic board multimaterial
...electronic board multimaterial
thingiverse
electronic board multimaterial mod
thingiverse
free
Electron Ring by RikerLansdale
...electron ring by rikerlansdale
thingiverse
connects to the proton and has the electrons on it
thingiverse
free
Electron in LArTPC by lululaplap
...electron in lartpc by lululaplap
thingiverse
electron showering in a lartpc detector
No
thingiverse
free
IKEA Vaxer net pot by khrazik
...these are meant to be printed upside down with no ...
thingiverse
free
Quiet control box for SKR 1.4 + cable mgmt layer. by Evilkoal
...if anything is weird, but i haven't noticed anything no ...
thingiverse
free
UVA Mens' Basketball 2018-19 NCAA Trophy by the_qsr
...ncaa trophy) to the remix sources list: https://www.thingiverse.com/thing:757912 in hono of the uva mens' basketball team of 2018-19: https://www.youtube.com/watch?v=hxa3xd4dxcy...
thingiverse
free
Volcano Nozzle Case by garethps
...er nozzles. i could have just stretched it but then the number inserts wouldn't have fit properly, hence my first ever remix!
thingiverse
free
Savage Dragon - Image Comics by ZMilab
...s in my mini style.
if you want more models released weekly and access to exclusives join my patreon!
patreon.com/ziemba3d
enjoy!
thingiverse
free
Concordia and Britannia & Germania expansion boardgame insert by MitutoyoRaytek
...sleeves up to 63x96mm (thin ones, thicker ones might no fit into the card holder). all the containers have...
thingiverse
free
Renna by Legname
...renna by legname
thingiverse
renna in compensato da 3mm
thingiverse
free
Extension Cord Cable Mount Clip by max_davis
...x_davis
thingiverse
cable mount that fits a standard extension cord cable (up to 9mm). just use two screws or nails to mount it.
thingiverse
free
VESA monitor mount French Cleat by Rockster160
...at least one stud with the bracket- as per nomal mounting standards. take caution, have somebody help you and...
thingiverse
free
GBS Zero Rain / Reverse Light IVA Angled Gasket by SeanWally
...pu.
the design includes a small seat adapter make sure that bolts used to secure the light are still mating at the correct angle.