Thingiverse
SAJ Test by merlinds
by Thingiverse
Last crawled date: 3 years, 1 month ago
I wanted to increase my overall printing speed but i was unable to find any test that will show me when I went to far on settings.
So I created this one, it prints fast, uses low material and shows what I think are most signs of speed excess.
Things that govern overall speed:
Acceleration, speed rate of change
Jerk, speed "jumps" for short movements
Speed, this is actually max speed.
First make sure your belts are well tighten, if you don´t know how, google it.
Also, chek that all your printer is well tighten, all bolts and nuts.
It will be a good time to check that your bed and carriage roon smoothly, again google.
I your printer has EPROM enabled you can change accel and jerk from Control-Motion
If not you will need to modify your firmware, for marlin 1.1.8 in Configuration.h
Jerk:
define DEFAULT_XJERK 20.0
define DEFAULT_YJERK 20.0
Accel:
define DEFAULT_ACCELERATION 1200
Also you will need to configure speed from firmware
Other thing you may need to change is temperature, I ended up printing at 235°C, to be able to reach 120mm/s
You should look for layer miss aligning and ghosting, also missing layers and extruder skipped steps.
Also you may notice that when you print too fast your prints will loss gloss. If you overstrech with speed you may endup lossing layer adhesion.
In my case with my crappy but heavly moded geeetech prusa, I went from:
60mm/s printing and 80mm/s travel
20 Jerk
1000 accel
to:
120mm/s printing and 150mm/s travel.
30 Jerk
2000 accel
Print quality decreased a bit but print time went down by about 40% for large prints.
Now the problem is noise jajajajja
So I created this one, it prints fast, uses low material and shows what I think are most signs of speed excess.
Things that govern overall speed:
Acceleration, speed rate of change
Jerk, speed "jumps" for short movements
Speed, this is actually max speed.
First make sure your belts are well tighten, if you don´t know how, google it.
Also, chek that all your printer is well tighten, all bolts and nuts.
It will be a good time to check that your bed and carriage roon smoothly, again google.
I your printer has EPROM enabled you can change accel and jerk from Control-Motion
If not you will need to modify your firmware, for marlin 1.1.8 in Configuration.h
Jerk:
define DEFAULT_XJERK 20.0
define DEFAULT_YJERK 20.0
Accel:
define DEFAULT_ACCELERATION 1200
Also you will need to configure speed from firmware
Other thing you may need to change is temperature, I ended up printing at 235°C, to be able to reach 120mm/s
You should look for layer miss aligning and ghosting, also missing layers and extruder skipped steps.
Also you may notice that when you print too fast your prints will loss gloss. If you overstrech with speed you may endup lossing layer adhesion.
In my case with my crappy but heavly moded geeetech prusa, I went from:
60mm/s printing and 80mm/s travel
20 Jerk
1000 accel
to:
120mm/s printing and 150mm/s travel.
30 Jerk
2000 accel
Print quality decreased a bit but print time went down by about 40% for large prints.
Now the problem is noise jajajajja
Similar models
thingiverse
free
Test Print by Gannan
...oto that i think i may need to tighten one of my belts. i notice some jerk on one of the square corners. so there's that too.
thingiverse
free
xnaron prusa/sprinter shudder test by xnaron
...settings are default. i tried setting max start as low as 1 but that did not help...still need to try lowering the accel speeds.
thingiverse
free
JRod's Overhang Hex Benchy by PsychoCap
...r raft support, but a brim adhesion is required. i will be releasing all kinds of 3d printer stress test/benchmarks periodically.
grabcad
free
Green Coffee Grano Price
...em, and use them properly, for your healthy weight loss and fast weight loss to occur. read more: http://www.greencoffeegrano.in/
thingiverse
free
Can Coozie FAST PRINT TPU Vase Mode by ksheyman
...f you want to print it fast.
there are two models - one for slim cans like white claw and one for fat cans like coke & pepsi.
thingiverse
free
Stepper Motor performance test by posrproductions
...f everything looks fine, the power of your printer is perfect. maybe you can retry the test with higher speeds and accelerations.
thingiverse
free
ANYCUBIC CHIRON Marlin 1.1.9 TMC2208/A4988 LOW JERK/ACCEL
...ompiled version.
latest official firmware provided in case of restoration needed. official autoleveling gcode provided if needed.
thingiverse
free
Heattower for Extruder Heat Calibration by zumili
...esults! so if you print your outer perimeters with let say an averange speed of 35mm/s then also print the heattower with 35mm/s.
thingiverse
free
Bowden e3d v6 mount for piezo holder by teikjoon
...piezo didn't trigger
after these firmware changes, g29 needs to be added after g28 (home all axis) to your slicer start gcode
thingiverse
free
JUMANJI DRAGONFLY by LocoBeeFPV
...d, 4mm/s initial layer jerk, 6mm/s regular layer jerk, 300mm/s accelerations, 1.5mm retraction distance, 35mm/s retraction speed.
Merlinds
thingiverse
free
Eraser and Marker Holder by merlinds
...y merlinds
thingiverse
used some double sided tape to stick it to the bottom of the board in my university. professors loved it.
thingiverse
free
Love Spinner by merlinds
...or my gf, still haven´t printed it, will upload pictures when i do.
i made it for a 22mm bearing and m6 nuts with a .2 clearence.
thingiverse
free
Moto g5 + Spell Book Case by merlinds
...moto g5 + spell book case by merlinds
thingiverse
this is a phone case i made for a friend.
thingiverse
free
Peppa Pig For easy print by merlinds
...hingiverse
just modified the original stl, to make it easier for printing. just put arms and tail flat surface on bed, and print
thingiverse
free
Organic Monitor Stand by merlinds
... monitor. it uses all the space available in a 20x20 bed and is really stable. also you can pass cables or store things under it.
thingiverse
free
Feline Skull by merlinds
...es to him.https://www.youtube.com/watch?v=comsn10azhk&lc=z23bvhlgjymqfjitracdp4342r3vrbspkiirkut4cn1w03c010c.1513420050131187
thingiverse
free
Utility Hexa Tile Durable by merlinds
... designed this one in a way that the little arms are printed layed down on the bed, also i med the whole frame more to my liking.
thingiverse
free
Philips OneBlade 2521 All in one holder by merlinds
...to hold the few accesories for my shaver. ended up mixing two existing designs.
printed with support only below the charger hole.
thingiverse
free
Titan Aero Double Layer Fan by merlinds
..., seriously this pumps some serious cooling, the silicon shell is a must for your heat block.
take a look: http://a360.co/2bbwl2r
thingiverse
free
Filament Spool Rack by merlinds
...unt it in.
in the pictures you will se an actual bearing, that is from an older version that proved to be useless so i remove it.
Saj
sketchfab
$25
Toolse Ordulinnuse varemed
...rootsi vägede valdusse. lõplikult purustati ta põhjasõja päevil 18. saj alguses. praegu on linnus varemetes. captured with dji m300...
sketchfab
$15
Puhja Püha Dionysuse Kirik
...arvatavasti 18. saj lõpust, uusgooti stiilis sisustus on 19. sajndist. 1868. aastal valminud altariseinal on maal “kristus ristil”. -...
grabcad
free
MISUMI CASTOR WHEEL SAJ 100
...misumi castor wheel saj 100
grabcad
misumi castor wheel saj 100
grabcad
free
clamp system for vice - 4 axis machine
...pripravo prirobnico boste lahko nadgradili svoje 4-osne rezkalne centre, saj vam tak sistem dela omogoča vpetje skoraj vseh mogočnih...
3dwarehouse
free
SAJ PRAHOVA
...saj prahova
3dwarehouse
sediul central #ambulanta_prahova
3dwarehouse
free
SAJ Prahova
...saj prahova
3dwarehouse
garaj, atelier auto #garaj_ambulanta
3dwarehouse
free
SAJ PRAHOVA
... prahova
3dwarehouse
sediul administrativ #112 #ambulance_services #ambulanta_prahova #emergency #serviciul_de_ambulanta_prahova
3dwarehouse
free
CAF - Saj
...caf - saj
3dwarehouse
centro de abastecimento farmacêutico desanto antônio de jesus #caf__saj
3dwarehouse
free
Sediul Administrativ SAJ PRAHOVA
...aj prahova
3dwarehouse
sediul administrativ saj prahova #112 #als #ambulance #ambulanta #atls #bls #emergency #training #urgenta
Test
turbosquid
$99
test
...st
turbosquid
royalty free 3d model test for download as max on turbosquid: 3d models for games, architecture, videos. (1251637)
turbosquid
$63
TEST
...st
turbosquid
royalty free 3d model test for download as max on turbosquid: 3d models for games, architecture, videos. (1446233)
turbosquid
$1
test
...st
turbosquid
royalty free 3d model test for download as fbx on turbosquid: 3d models for games, architecture, videos. (1360941)
3d_export
free
johnny test
...johnny test
3dexport
johnny test 3d
turbosquid
$15
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Test
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
gripper test
...gripper test
3dexport
robot gripper test model