Thingiverse
S3 Pattycake FPV Hovercraft / Tiny Whoov by nickleyw
by Thingiverse
Last crawled date: 3 years ago
Convert your quadcopter into a hovercraft - introducing the S3 Pattycake FPV Hovercraft!
This version uses 6mm brushed motors. Look here for a remix that uses 0603 brushless motors.
Features:
prints in two parts, no support needed
parts snap together
snap-in camera mount
snap-in motor mounts
snap-in flight control board mount
slide-in battery mount
"all-up" weight of less than 38 grams with all components, battery!
NO glue required!
NO programming required!
NO wire extensions or additional soldering required!
Required: one of several common quadcopters, like the blade inductrix, blade inductrix FPV, or any tiny whoop variation.
Instructions:
move your flight controller, FPV camera, motors and propellers to the new S3 Pattycake frame. Be sure front motors stay in front (main body), rear motors stay in rear motor mounts.
note: press in motors from the underside and rear of motor mounts. They will not push all the way through the mount, they should sit just below the motor mount's top/front surface under a small lip.
when plugging in your motors, plug front-left motor into back-left port, back-left motor into front-left port, and same on the right side... this will keep your S3 Pattycake from spinning out of control
Piloting:
use your throttle/yaw stick for everything!
Enjoy :P
This version uses 6mm brushed motors. Look here for a remix that uses 0603 brushless motors.
Features:
prints in two parts, no support needed
parts snap together
snap-in camera mount
snap-in motor mounts
snap-in flight control board mount
slide-in battery mount
"all-up" weight of less than 38 grams with all components, battery!
NO glue required!
NO programming required!
NO wire extensions or additional soldering required!
Required: one of several common quadcopters, like the blade inductrix, blade inductrix FPV, or any tiny whoop variation.
Instructions:
move your flight controller, FPV camera, motors and propellers to the new S3 Pattycake frame. Be sure front motors stay in front (main body), rear motors stay in rear motor mounts.
note: press in motors from the underside and rear of motor mounts. They will not push all the way through the mount, they should sit just below the motor mount's top/front surface under a small lip.
when plugging in your motors, plug front-left motor into back-left port, back-left motor into front-left port, and same on the right side... this will keep your S3 Pattycake from spinning out of control
Piloting:
use your throttle/yaw stick for everything!
Enjoy :P
Similar models
thingiverse
free
S3 Ninja Star 2018 - indoor FPV racing drone - tiny whoop by nickleyw
...bind button preferred) beebrain betafpv stock blade inductrix other similary sized brushless boards while assembling (instructions and video coming...
thingiverse
free
Inductrix FPV 20 degree camera mount by AlternativeRC
...the camera securely, and added a third screw hole at the back of the mount, maybe it wasn't necessary, but i figured why not?
thingiverse
free
Tiny whoop Inductrix Case by babar121
...lds 6 batteries and the quadcopter itself. shown with hyperion fpv camera/vtx and mount http://www.thingiverse.com/thing:1532755.
thingiverse
free
Tiny Whoov Lite- Low Profile Inductrix Hovercraft by mambamax
...e camera mount which holds the camera 15mm above the fc, i haven't personally run this one yet so i'd love some feedback!
thingiverse
free
Crazepony CM275T FPV Micro AIO Camera 5.8G 48CH 25mW Transmitter Inductrix Mount by teckn0
...ound at:https://johnbrisbois.com/content/tiny_whoop_inductrix_fpv_plus_flight_controller_buildhttps://rotorbuilds.com/build/13682
thingiverse
free
Blade Inductrix FPV Camera Mount - Tiny Whoop by NorCAL3D
...and your ready to fly.
update: added 0 and 10 degree mounts in a lite configuration, also added a lite 20 degree. go whoop it up!
thingiverse
free
NanoCam3D Mk.1 mount for Inductrix® FPV plus Frame by KritzelKratzel
...am3d mk.1 mount for inductrix® fpv plus frame by kritzelkratzel
thingiverse
a camera mount for blade® inductrix® fpv plus frame.
thingiverse
free
Inductrix FPV Camera Mount - Alternative Mount by S_Smitka
...me, as well as easy snap-in/lock for the camera and it's transmitter.
the camera mount is design to be at a 10 degree angle.
thingiverse
free
Blade Inductrix Frame w/Snap In Battery Mount by Fila_Mentor
...zzle, slowly with supports. also, the battery mount should be positioned (flipped 180) so the side with the clips are on the bed.
thingiverse
free
Micro Mauler 106 - FPV Quadcopter w/ 7mm Motors - BeeBrain - Inductrix by Airmaxx23
...ike this designed to work with the stock hubsan x4 flight controller just leave a comment below and i will draw one up.
have fun.
Pattycake
thingiverse
free
Case for S3 Pattycake FPV Hovercraft by Crimson_Drake
...mple case for the s3 pattycake fpv hovercrafthttps://www.thingiverse.com/thing:2783467
the top is 3mm thick to edd a text or logo
3dwarehouse
free
Spainish Casa
...out and configure. couldn't of done it without 'mr. pattycake#39; #casa #castle #dream_house #missionary #palace #spain #spainish...
Nickleyw
thingiverse
free
Micro USB Dust Cover by nickleyw
... nickleyw
thingiverse
plugs into micro usb port to keep out dust. please be careful installing and removing to prevent breakage!
thingiverse
free
S3 Nano FPV Champion Trophy by nickleyw
...o fpv champion trophy by nickleyw
thingiverse
this trophy is perfect for crowning the champion of an fpv nano race - tiny whoop!
thingiverse
free
S3 Ninja Star 2017 - indoor racing drone by nickleyw
... alternative for the blade inductrix, tiny whoop or similar nano-sized fpv drone.
updated version available - s3 ninja star 2018
thingiverse
free
Touchscreen No Touch Tool by nickleyw
...each of your key-chains so you'll never have to touch a grimy touchscreen or keypad again! yes, it also works on smartphones!
thingiverse
free
S3 Ninja Star 2018 - indoor FPV racing drone - tiny whoop by nickleyw
...and snap-off the arrow tabs
over the posts, lay the battery holder, snap-in your flight controller, then snap-in the camera mount
thingiverse
free
HTC Re Camera sealing gasket ring with USB insert by ryaninc
...at htc's official gasket for comparison: https://www.htc.com/us/accessories-b/#!pid=re-camera&acc=re-protection-pack thanks to nickleyw for the microusb piece...
thingiverse
free
MIDI / TINY WHOOV 8.5cm MOTORS 1S or 2S Lipo FPV optional by Johnandvix
...chose this design because of its simplicity ,i contacted nickleyw about getting the files to modify it and he...
Whoov
thingiverse
free
Mitchie Whoov - No Supports Tiny Whoov by NuRxG
...t!
the fc mounts on bottom, and you should be able to use standard length motor wires. battery wire passes through the butt hole.
thingiverse
free
Tiny Whoov by kellyullrich
...use m3 nylon screws to attach the fan ducts to the body. the flight controller rests in the printed bobbins, no need for screws.
thingiverse
free
Bumper for Tiny Whoov Lite by firstry
...max "tiny whoov lite" https://www.thingiverse.com/thing:2778070
print it in tpu, otherwise it won't fit and bump...
thingiverse
free
Tiny Whoov - laser cuttable by raptor_demon
...laser cuttable by raptor_demon
thingiverse
modified the original files to be laser cut table and sized it to fit on a k40 laser.
thingiverse
free
12.5mm cam mount for "tiny whoov lite" by firstry
...amax "tiny whoov lite" https://www.thingiverse.com/thing:2778070
fit is a little loose. just fix it whith a rubberband.
thingiverse
free
Tiny Whoov motor mount by DyoGTS
...e to fit 5mm foam board and allows you to adjust the angle as desired (i found that the motors angled upward increases the speed)
thingiverse
free
tiny whoov camera mount for eachine tx04 aio by Dogatech
...amera lens is not centered on the board.
this is meant to go with my tiny whoov design: https://www.thingiverse.com/thing:2992613
thingiverse
free
3 motor - Tiny Whoove by Mpit52
...duct. the rear thrust arms were designed for 40mm props but should be able to run 60mm props if the motor is set back far enough.
thingiverse
free
Tiny Whoov Extra Light Thrust Mod by tavdog
...board to clear external obstacles like walls. also cut off the tops of the thrust motor mounts since need to glue them in anyway.
thingiverse
free
TINY WHOOV - SCRATCHBUILD (v1) by Badassdrones
...alex (@badassdrones on instagram)
get all the electronics you need to make an awesome tinywhoov here :https://badassdrones.fr/en/
Hovercraft
3d_export
$15
hovercraft
...hovercraft
3dexport
3d_ocean
$40
Hovercraft
...nd me an email through my account if you are interested but may need it in a different format, i will see if i can do it for you!
3d_ocean
$40
Hovercraft
...th individual pieces of cargo which are also textured. the engines have moveable prop shafts and rudders for animation purpose...
turbosquid
$3
hovercraft
... 3d model hovercraft for download as 3ds, obj, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1312123)
turbosquid
$20
Hovercraft
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Hovercraft
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Hovercraft
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
Hovercraft
...download as 3ds, max, dxf, obj, fbx, dwg, blend, dae, and stl on turbosquid: 3d models for games, architecture, videos. (1261865)
3d_export
$20
hovercraft
...g projects, and was originally modeled in 3ds max 2012 and rendered with v-ray. renders have no postprocessing. hope you like it!
turbosquid
$15
Hovercraft Racing
...uid
royalty free 3d model hovercraft racing for download as on turbosquid: 3d models for games, architecture, videos. (1410557)
S3
3d_ocean
$8
Samsung S3
...samsung s3
3docean
3d mobile s3 samsung
this is fully detailed samsung galaxy s3 phone model.
3ddd
$1
Masiero Mir S3
...masiero mir s3
3ddd
masiero
люстра masiero mir s3
turbosquid
$5
s3.max
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
design_connected
$13
Sempé w103 s3
...sempé w103 s3
designconnected
wästberg sempé w103 s3 computer generated 3d model. designed by sempé, inga.
3ddd
$1
Galaxy S3
...galaxy s3
3ddd
samsung , телефон
samsung galaxy s iii
3ddd
$1
Samsung Galaxy S3 mini
...samsung galaxy s3 mini
3ddd
samsung , телефон
samsung galaxy s3 mini
3d_export
$5
Samsung Galaxy S3 3D Model
...samsung galaxy s3 3d model
3dexport
s3
samsung galaxy s3 3d model satssammee 62061 3dexport
3d_export
$5
Samsung galaxy s3 3D Model
...samsung galaxy s3 3d model
3dexport
samsung galaxy s3
samsung galaxy s3 3d model andrejj 65260 3dexport
turbosquid
$30
samsung gear s3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Tree s3 3ds
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Fpv
turbosquid
$1
FPV VTX Antenna
...e 3d model fpv vtx antenna for download as obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1230317)
3d_export
$9
Fpv logo 3D Model
...onogram vehicle part of auto transport 3d model logo emblem detailed high quality badge
fpv logo 3d model rmodeler 59628 3dexport
3d_export
$8
dji fpv battery slot holder
...er for 3 dji fpv batteries. holds perfectly without shaking. need 1 m3 countersunk head bolt. need to print 6 pin, 1 case, 1 cap.
3d_export
$10
fpv camera hd 700tvl
...aterials are logically named<br>the main format is in 3ds max 2009.<br>satisfcation garranteed..<br>thank you !
thingiverse
free
FpV Mount (SOPORTE FPV) by elborjas1987
...fpv mount (soporte fpv) by elborjas1987
thingiverse
this is a fpv mount with the same holes of naza base.
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
FPV DRONE ROOSTER DJI FPV PART
...fpv drone rooster dji fpv part
thingiverse
fpv drone rooster dji fpv install part
thingiverse
free
FPV monitor
...tml?rmmds=myorder&cur_warehouse=cn
link for download : https://cults3d.com/fr/mod%c3%a8le-3d/divers/fpv-monitor-ecran-fpv-faf
thingiverse
free
FPV receiver mount for FPV display by petrex
...eceiver mount for fpv display by petrex
thingiverse
aomway receiver mount for field view 777 fpv monitor. with small cable tray.
Tiny
turbosquid
$3
Tiny Mushroom
...squid
royalty free 3d model tiny mushroom for download as ma on turbosquid: 3d models for games, architecture, videos. (1562284)
turbosquid
$2
Tiny Tank
...osquid
royalty free 3d model tiny tank for download as blend on turbosquid: 3d models for games, architecture, videos. (1542044)
turbosquid
$3
Tiny Knife
...
royalty free 3d model tiny knife for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1358937)
3d_export
$5
Tiny house
...tiny house
3dexport
https://www.dock4all.com/
3d_export
free
Tiny Toy
...tiny toy
3dexport
turbosquid
$30
Tiny Tank
...lty free 3d model tiny tank for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1608730)
turbosquid
$20
Tiny houses
...lty free 3d model tiny house for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1642651)
turbosquid
$100
Tiny boy
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$50
Tiny Man
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
Tiny House
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.