Root2cnc with large tool by giamma

...d also on other cnc machine. the support has a curvature suitable for a 52mm spindle but can be easily adapted to other spindles.

...rough for additional stability. requires a printbed of at least 300mmx250mm do not print with fill below 35% recommended is 40%.

...m have a look to the laser operating: https://www.youtube.com/watch?v=k-64c0ddzdq always wear glasses when operating with laser !

...c forum here.https://rootcnc.com/forums/topic/a-1200x1200mm-root2-1-or-3-with-40x40-rails/#post-1082 https://youtu.be/4buil51npeu

...inted parts customization (make it bigger) cheap simple use parts commonly used in diy 3d printer easily sourced parts

...soon: microrap 200 with full sized heated bed capacity. here is a video of the prototype microrap 200https://youtu.be/4t9eik2gnua

...d also on other cnc machine. the support has a curvature suitable for a 52mm spindle but can be easily adapted to other spindles.

...rough for additional stability. requires a printbed of at least 300mmx250mm do not print with fill below 35% recommended is 40%.

...c forum here.https://rootcnc.com/forums/topic/a-1200x1200mm-root2-1-or-3-with-40x40-rails/#post-1082 https://youtu.be/4buil51npeu

...m have a look to the laser operating: https://www.youtube.com/watch?v=k-64c0ddzdq always wear glasses when operating with laser !

...us on facebook! upload idea's, photos and any updates https://www.facebook.com/root2cnc https://www.facebook.com/groups/1023078667749894/ introduction i started this project to enable me...

...smaller, homemade cnc mills such as the mpcnc and root2cnc use 1/4" or 6mm wood. everything wooden in the...

...large soapdish by giamma thingiverse soapdish

...football pedestal by giamma thingiverse football pedestal

...support for radio thermostat by giamma thingiverse support for radio thermostat - freecad customizable file

... giamma thingiverse car holder for navigon nav. to attach it to the air ventilation i have used some clips found on the market.

...drawer (similar to this http://www.prontohobbyshop.it/prodotto/guida-per-cassetto-micro/28-cm/nc/6665) and standard m8 thread bar

...quire two steel rod of 8 mm 4 elastic spring and one rod thread rod of 8m. this vise also compensate a non parallel border of pcb

...andard utility tool for bend properly electronic components before soldering on printed circuit according to the standard steps

...probably some adjustment in the parameter. ( i have buy three time from the same supplier this tft and every time are different.)

...large table by leonk thingiverse large table

...large bracelet by gepetto thingiverse large bracelet

...large basket by davidmurry thingiverse large basket

...large trellis by rkxone thingiverse large trellis

...e holes for large handled toothbrushes by tvickers thingiverse toothbrush holder with large hole for large handled toothbrushes.

...large box by tward891 thingiverse large storage box

...large screwcup by redtopper thingiverse contains large things!

...ngiverse this is a large ant nest with both a section for a large colony and a section for a small colony. mmmmmmmmmmmmmmmmk bye

...large key by benjykid thingiverse this is a large key. this is for decoration or theater.

...carrus large shuttle thingiverse large shuttle arvus like

...tool holder tool box thingiverse !

...teng tools tool set hinge thingiverse hinge for teng tools tool set.

... holder for 8mm lathe tools thingiverse tool holder for 8mm lathe tools. there is 11 slots because i have 11 tools in my pack :)

...tool holder for small tools by darak_chen thingiverse a little tool holder witch fits on you desk for small tools!

...tools by nhcraig01 thingiverse this is just a simple tool holder for various tools i found useful for tinkering on a 3d printer.

...tool box tool holder by fpvitall thingiverse a simple and spacesafing tool stand or desktop organizer

...tools by kallik thingiverse tools

...tools by kallik thingiverse tools

...tools by kallik thingiverse tools

...tool by nagato thingiverse tool