Thingiverse
Rigidbot Motherboard holder by jacobsdr
by Thingiverse
Last crawled date: 3 years, 4 months ago
Created a basic rigidbot motherboard case. I used spacers to elevate the board and drilled some holes for airflow. Plenty of room to add fan. Also the extension under the cables allows to attach cable supports since the cables (particularity the power cable) are heavy and put stress on the connection on the board. I found just the extension helps but additional support would be a good idea. Yes I know the bolts I used were too long but they allow for air flow at least.
Similar models
thingiverse
free
Rigidbot Cable Support by DesertEagle50AE
...ve designed it to relief the stress in the cables near the plugs in order to prevent cable breaks.
have fun printing an using it!
thingiverse
free
Rigidbot RUMBA case by rwintle
...pports 2 30mm fans to cool drivers, etc. usb port remains accessible. power input is designed to leverage powerwerx connectors.
thingiverse
free
Rigidbot Flat Cable Clamp by pdidonna
...le clamp by pdidonna
thingiverse
flat ribbon cable clamp for rigidbot extruder. use with 25mm flat braided expandable sleaving.
thingiverse
free
RigidBot Ribbon Cable Managment Clip by virtualight
...alight
thingiverse
this clip was designed to manage the cables from a dual extruder with an on board inductive proximity sensor.
thingiverse
free
Alligator Board Support for 2020 profile
...ot;alligator", that allows to fix it to the 2020 profile.
the side holes are used to secure cables to the support with ties.
thingiverse
free
Rigidbot Back Cover for PSU Replacement (Nunus PSU) by yenlo
...the red cables for - and black for + )
no screws are needed. the ribs on the outside will give the cover a tight fit on the psu.
thingiverse
free
Support SD Extension Cable by jdeleonp
...support sd extension cable by jdeleonp
thingiverse
one support for sd cable extension
thingiverse
free
RigidBot Mainboard Support by tchotchke
...leaves space for a 60mm x 60mm x 10mm fan.
warning: be careful to avoid covering the stepper drivers if you install this part..
thingiverse
free
SD Card extension cable support by Lumyn
... lumyn
thingiverse
sd card extension cable support.
buy a simple extension cable for sd card compatible with your printer and...
thingiverse
free
Rigidbot Power Supply Mount by Canaboost
...support to allow you to lift the rigidbot with the power supply in place however i would recommend securing it with a few screws.
Jacobsdr
thingiverse
free
Receiver 1 replacement file by jacobsdr
...receiver 1 replacement file by jacobsdr
thingiverse
jyn erso blaster pistol by swarleyaus, a fix to the receiver 1 file.
thingiverse
free
Repaired vacuum attachment by jacobsdr
...thingiverse
the original file had two bodies in model. this did not slice well in s3d so i removed the second body in meshmixer.
thingiverse
free
Simple picture or mirror corner mount by jacobsdr
...or corner mount by jacobsdr
thingiverse
super simple picture or mirror corner mount. uses just two picture frame hanging nails.
thingiverse
free
pi Looper by jacobsdr
...h and printing. side file was originally called walls. i just made joined all the pieces to make get rid of the multiple shells
thingiverse
free
He 162 nose replacement by jacobsdr
...n't have any thickness to it at least in s3d, i mesh mixed it to get some thickness and the cut it flush for easier printing.
thingiverse
free
SmartThings Hub (Gen2) Wall Mount - Ports on Bottom by neonpolaris by jacobsdr
...in s3d it was two objects and the print would have been very weak structurally. i repaired the model so it is only one piece now.
thingiverse
free
K9 K-9 doctor who by jacobsdr
...up the model 550% so if people use my remix keep that in mind for the rest of the pieces. thank you c4robotics for a great model!
thingiverse
free
Vibration reducing corner pieces for (feet) rigidbot. by jacobsdr
...rt material underneath but the lip is only 2mm thick so my support material removed cleanly, actually one of the best i have had!
Rigidbot
thingiverse
free
z_bracket rigidbot
...z_bracket rigidbot
thingiverse
z_bracket for 4 screws
thingiverse
free
Rigidbot Side Brackets by MKAY666
...rigidbot side brackets by mkay666
thingiverse
rigidbot side and z brackets
thingiverse
free
RigidBot Caliber Holder by dafes
...rigidbot caliber holder by dafes
thingiverse
caliber holder for the rigidbot frame
thingiverse
free
Rigidbot printerbed by nickbernstein
... printerbed by nickbernstein
thingiverse
build plate for rigidbot 3d printer. intended to be be c&c fabricated from aluminum
thingiverse
free
Filament Guide for Rigidbot by omegdadi
...filament guide that clips onto the frame of a rigidbot 3d printer. inspired by the rigidbot side cutter tool holder by steve0605.
thingiverse
free
Rigidbot End Cap by pdidonna
...rigidbot end cap by pdidonna
thingiverse
end cap to plug up the ends of the rigidbot frame
thingiverse
free
RigidBot monitor by EremaStar
...rigidbot monitor by eremastar
thingiverse
lcd
thingiverse
free
RigidBot Z-Axis Support by dafes
...rigidbot z-axis support by dafes
thingiverse
support structure for the z-axis upgraded rigidbot.
thingiverse
free
RigidBot Bar End Cap by tchotchke
...rigidbot bar end cap by tchotchke
thingiverse
push in end cap for covering the ends of the rigidbot bars.
thingiverse
free
Rigidbot Hex Key Holder by Steve0605
...rigidbot hex key holder by steve0605
thingiverse
a place to keep your hex keys handy for the rigidbot printer.
Motherboard
thingiverse
free
motherboard cover by Shurikkun
...motherboard cover by shurikkun
thingiverse
motherboard cover
thingiverse
free
motherboard atx by joselcl98
...motherboard atx by joselcl98
thingiverse
motherboard model atx
thingiverse
free
Motherboard by GameAddict
...motherboard by gameaddict
thingiverse
hi! i used 123d catch to get this 3d model. it's an old dell motherboard
thingiverse
free
Motherboard Mounts by dvan
...motherboard mounts by dvan
thingiverse
mounts to mount your motherboard...
thingiverse
free
Motherboard Standoff by maxharrison
...doff by maxharrison
thingiverse
this is a motherboard standoff that is designed to be positioned into place and then glued down.
thingiverse
free
TATARA motherboard case
...ra motherboard case for original anet 1.0 motherboard.
i used m3x8mm screws to attach the door case.
enjoy it and show your print
thingiverse
free
Motherboard ATX 1.0 by Juanch616
...motherboard atx 1.0 by juanch616
thingiverse
motherboard matx 1.0
thingiverse
free
Flexbot Motherboard-Cover by Inspiration
...flexbot motherboard-cover by inspiration
thingiverse
motherboard-cover for flexbot
thingiverse
free
Aorus MotherBoard Logo by DanielHC
...aorus motherboard logo by danielhc
thingiverse
logo for the motherboard aorus ryzen
thingiverse
free
M3A78 MotherBoard BackPlate by EvgenRU
...m3a78 motherboard backplate by evgenru
thingiverse
back panel for asus m3a78 motherboard
Holder
thingiverse
free
Stubby holder holder
...der
thingiverse
bottom on the holder is sized for a can or bottle. top of the holder is sized for one in a cooler/stubby holder.
thingiverse
free
Soap holder holder
...soap holder holder
thingiverse
it's a holder to hold the famous soap holder.
thingiverse
free
bottle holder Jar holder can holder
...bottle holder jar holder can holder
thingiverse
hole diameter 38.6mm
thingiverse
free
Spool holder holder by vemotion
...spool holder holder by vemotion
thingiverse
pipe holder (16mm diameter)
thingiverse
free
smartphone holder with usb cable holder and key holder
...other of invention
this is my first creation basically smartphone holder with usb cable holder and key holder
i hope you like it
thingiverse
free
Holder of plate holders by budvar
...t; ;) holder for 5 pieces of modular plate holders from dave o https://www.prusaprinters.org/en/prints/15367-modular-plate-holder
thingiverse
free
Pen Holder/card holder by Pinky561
...pen holder/card holder by pinky561
thingiverse
a pen holder/card holder in one.
thingiverse
free
Toilet paper holder with phone holder
...toilet paper holder with phone holder
thingiverse
toilet paper holder with phone holder
thingiverse
free
Radio equipment holder and microphone holder
...radio equipment holder and microphone holder
thingiverse
radio equipment holder and microphone holder
thingiverse
free
Popsicle Holder Holder by billiamthesecond
...popsicle holder holder by billiamthesecond
thingiverse
keep popsicle holders upright so that they can be set down